Search results
Create the page "Bus type" on this wiki! See also the search results found.
Page title matches
Page text matches
- | Bus type = ISA | Bus width = 8-bit1 KB (211 words) - 16:06, 13 February 2016
- | Bus type = ISA | Bus width = 8-bit1 KB (194 words) - 16:38, 13 February 2016
- | Bus type = ISA | Bus width = 16-bit2 KB (315 words) - 16:12, 13 February 2016
- | Bus type = ISA | Bus width = 8-bit2 KB (227 words) - 16:00, 13 February 2016
- | Bus type = ISA | Bus width = 16-bit2 KB (245 words) - 17:11, 13 February 2016
- The bus type is a [[Has type::text]] field containing only one of the following permitted values: ** '''[[Allows value::ISA]]''' - original ISA bus1 KB (251 words) - 19:59, 23 April 2016
- ...nly one of the following permitted values, which vary depending on the bus type:976 bytes (162 words) - 00:25, 4 February 2016
- | Bus type = PC Floppy | Bus width = 1-bit2 KB (237 words) - 21:32, 25 March 2016
- [[Bus type::+]] <!-- Exclude non-device pages also in the above category --> | ?Bus type345 bytes (51 words) - 21:34, 25 March 2016
- | Bus type = ISA | Bus width = 16-bit1 KB (147 words) - 15:10, 13 February 2016
- | ?Bus type | ?Bus width705 bytes (107 words) - 22:13, 25 March 2016
- === A-type (1S DD 40T) === === B-type (2S DD 40T) ===5 KB (828 words) - 18:16, 31 December 2016
- | Bus type = PC Floppy | Bus width = 1-bit904 bytes (127 words) - 21:32, 25 March 2016
- ...dicating whether an IDE interface can be set as the first, or primary, IDE bus in the system. Typically this is at I/O address 0x1F0 and uses IRQ 14.180 bytes (34 words) - 14:31, 13 February 2016
- ...icating whether an IDE interface can be set as the third, or tertiary, IDE bus in the system. Often this is at I/O address 0x1E8 and uses IRQ 11 or 12.183 bytes (35 words) - 14:31, 13 February 2016
- ...ting whether an IDE interface can be set as the fourth, or quaternary, IDE bus in the system. Oten this is at I/O address 0x168 and uses IRQ 10 or 11.185 bytes (34 words) - 14:31, 13 February 2016
- ...ating whether an IDE interface can be set as the second, or secondary, IDE bus in the system. Typically this is at I/O address 0x170 and uses IRQ 15.183 bytes (33 words) - 14:31, 13 February 2016
- ...ver some controllers exist where up to four drives can be attached to each bus. In those cases, either a custom Shugart-style cable is used with five con ...t, pay special attention to whether these are attached to the same 4-drive bus, or whether they appear as two separate 2-drive buses.874 bytes (154 words) - 14:44, 13 February 2016
- | ?Bus type | ?Bus width539 bytes (81 words) - 15:05, 13 February 2016
- ...dard PC floppy cables to connect a total of four drives to the same floppy bus. ...sing LS-120 drives which can read 3.5" floppy disks and connect to the IDE bus instead.2 KB (346 words) - 15:30, 13 February 2016