Search results
Create the page "AT Motherboards" on this wiki! See also the search results found.
- ...r this is Unreal (1998), a game that was geared towards software rendering at first, but had a Glide renderer added during development as soon as it was ...for 3dfx cards. This was again due to 3dfx being the dominant 3D solution at this time, and also a commonly known brand with PC gamers. If software does32 KB (5,353 words) - 22:25, 15 June 2022
- ...such as blurriness, loss of color saturation and color bleed, particularly at higher resolutions and refresh rates. Determining which cards are high qual ...eatures and the high end models have the performance to use these features at higher resolutions. GeForce 6 drops support for palettized textures, which19 KB (3,051 words) - 08:13, 13 January 2019
- ...ossible run them on a 50MHz bus (in 2X mode). Intel documentation and some motherboards mention support for a 2.5X multiplier setting, however this was removed bef ...board jumpers. DX4 overdrives included integrated VRMs for use on older 5V motherboards, however they were multiplier locked.14 KB (2,343 words) - 00:11, 19 October 2020
- *[[XT Motherboards | XT]] / [[AT Motherboards | AT]] / [[386 Motherboards | 386]] ([[386 Chipsets | 386 Chipsets]] ) *[[Socket 1-3 Motherboards | Socket 1-3]]797 bytes (80 words) - 22:11, 4 February 2016
- ...inal P5's 5.0v. This was a die shrink revision of the Pentium and operated at 75-120MHz with a bus speed of 50MHz, 60MHz or 66MHz. Socket 5 motherboards are built to the AT specification, and typically use PCI and ISA slots. Some with OPTi chipset8 KB (1,304 words) - 15:49, 29 March 2022
- ...ed 32-bit data paths. These motherboards allowed SIMMs to be installed one at a time, but were best avoided due to their poor performance. All Socket 4 motherboards were made as baby AT motherboards or in proprietary formfactors for OEMs.2 KB (305 words) - 11:38, 26 November 2015
- ...e worst case, running 8/16-bit code, the PPro can be slower than a Pentium at the same clock speed. In the best case with 32-bit code or heavy FPU operat ...ked also, but will provide a speed up to around 1000MHz. Some of the 440LX motherboards had issues with powering more modern AGP graphics cards.22 KB (3,456 words) - 10:00, 17 December 2020
- ...me considerably more power than Pentium II and III. Make sure your PSU has at least 20A on 5v for Slot A and early Socket A boards. ...Socket A) and later as a Sempron (which was basically a renamed Athlon XP at first). While Duron was marketed with it's original clock speed, Athlon XP8 KB (1,239 words) - 12:18, 21 February 2013
- ...n 1996 the specifications had changed breaking compatibility with socket 2 motherboards. It was a 238-pin low insertion force (LIF) or zero insertion force (ZIF) 1 ...3.3V CPU's in addition to the older 5V CPU's (even though not all Socket 3 motherboards did in fact support 3.3V CPU's). It was also one of the first CPU sockets t7 KB (1,113 words) - 08:21, 11 October 2020
- ...on to produce 16 and 20MHz versions whereas Intel's fastest 286 was rated at 12.5MHz. ...U, the questionable "PR" rating system and AMD's inability to produce them at higher clock rates.13 KB (2,290 words) - 18:04, 22 October 2015
- ...e Diablo and Starcraft had required specifications of P60-P90 systems with at least 16 MB of RAM. A high-end 486 will run these particular games as well. ...ith a supported CPU, which can be up to a Pentium III "Tualatin" with some motherboards. Another popular target is a K6-2 through K6-3+ combined with a Ali1541 chi5 KB (836 words) - 13:29, 4 March 2013
- ...ndows games compatibility. Almost anything from 1990 to 1998 can be played at reasonable framerate and with enough comfort. Pentium MMX processors are supported by later Socket 7 motherboards with '''split rail voltage'''. Not every motherboard will accept such a CPU12 KB (2,001 words) - 04:26, 5 April 2013
- ...r_CPUs|WinChip CPUs]]. It is not competitive with Intel Celeron unless run at a much higher relative clock speed. The Cyrix IIIs and C3s did however cons ...ull speed instead of the half speed all the previous C3s had their FPU run at.2 KB (323 words) - 21:51, 24 December 2015
- ...be installed in motherboards with specific BIOS/chipset support. However, motherboards can often be modified by those with good skills. 486xLC chips were later so ...available in a "dingus" that sat between the CPU and socket. 486S also ran at 4V, versus the standard 5V of Intel and AMD chips of the time. Performance5 KB (886 words) - 18:01, 22 October 2015
- *[[New mainboards with old features|List of modern motherboards with legacy features like IDE, floppy, serial and parallel ports]] *[[Fast_ISA_Motherboard_Lists|List of 'modern' motherboards featuring ISA-slots (s478/sA and beyond, industrial boards with ISA)]]1,009 bytes (147 words) - 08:51, 19 November 2020
- ...by [[ATi Technologies]] in the mid to late 1980s. These cards were unique at the time as they offered the end user a considerable amount of value by com ...e Mach32, integrated the VGA wonder core and coprocessor into a single IC. At this point the VGA Wonder line was cancelled and replaced with a cost reduc46 KB (7,128 words) - 22:56, 20 May 2021
- How to identify expansion card by just looking at it. *By looking at it's connectors (this helps in identifying what type of card it is)4 KB (672 words) - 02:29, 25 January 2014
- ...e to PC enthusiasts as the 486 was becoming obsolete (1994-1995). However, at the time they were an excellent bargain and could breathe new life into old3 KB (542 words) - 11:45, 27 December 2015
- ===80386 Motherboards=== ...ration high end 386 chipsets, however they are usually rated for operation at higher speeds (40MHz) and work well with fast memory timings.43 KB (5,288 words) - 21:11, 27 December 2015
- ''The list here is provided as-is, so use at your own risk.'' .../www.via.com.tw/en/products/processors/c3/boardlist.jsp List of compatible motherboards] (dead link, but added for the sake of completeness)7 KB (1,116 words) - 21:31, 24 December 2015
