Difference between revisions of "Intel 8∕16 LAN Adapter"
(→Boot ROM) |
(A few more tidbits...) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 18: | Line 18: | ||
}} | }} | ||
{{Device Infobox/End | {{Device Infobox/End | ||
| − | | Driver | + | | Driver = [ftp://ftp.oldskool.org/pub/misc/Hardware/Intel/8_16%20LAN%20ADAPTER/ Download Page] |
}} | }} | ||
| − | The '''Intel 8∕16 LAN Adapter''' is a 10Mbps network card. | + | The '''Intel 8∕16 LAN Adapter''' is a 10Mbps network card. It is notable for being compatible with the IBM PC/XT because of its dual 8-bit / 16-bit operating modes. There are several revisions of the card which have different physical interfaces at the back. Revisions include: RJ45 + dsub15, BNC + dsub15, and possibly more. |
== Additional photos == | == Additional photos == | ||
| Line 28: | Line 28: | ||
Image:Intel 8∕16 LAN Adapter underside.jpg|Underside | Image:Intel 8∕16 LAN Adapter underside.jpg|Underside | ||
Image:Intel 8∕16 LAN Adapter-filmag.jpg|Alternate card (Fil-Mag) | Image:Intel 8∕16 LAN Adapter-filmag.jpg|Alternate card (Fil-Mag) | ||
| + | Image:Intel_lan_8_16.jpg|Revision with RJ45 + dsub15 interfaces | ||
</gallery> | </gallery> | ||
== Boot ROM == | == Boot ROM == | ||
| − | This card's boot ROM socket | + | This card's boot ROM socket takes a standard 32-pin EEPROM chip, as well as 28-pin EEPROM chips such as the 28C64. It has been tested extensively with the 28C64 chip flashed with XT-IDE BIOS images, both XT and AT versions. It is a reliable way to boot from a modern era hard drive connected to an XT or AT class system whose BIOS would not natively support it. |
| − | The card's DOS drivers come with a configuration program (<tt>SOFTSET.EXE</tt>) that can be used to enable the ROM socket (it is disabled by default) and set the base address, as well as adjust all the usual options like the I/O address and IRQ. | + | == DOS Support == |
| + | |||
| + | The card's DOS drivers come with a configuration program (<tt>SOFTSET.EXE</tt>) that can be used to enable the ROM socket (it is disabled by default) and set the base address, as well as adjust all the usual options like the I/O address and IRQ. There is a configuration option to force 8-bit operation even while plugged into a 16-bit ISA slot. The packet driver for DOS works perfectly with the MTCP suite from FreeDOS. | ||
Latest revision as of 05:04, 23 April 2018
| Bus type | ISA |
|---|---|
| Bus width | 16-bit |
| Bus speed | 8 MHz |
| 8-bit ISA compatible? | Yes |
| Manufacturer | Intel |
| Chipset | i82586 |
| Connectors | AUI, BNC |
| Requires -5VDC? | No |
| Requires -12VDC? | No |
| Config method | Software |
| Ethernet | |
| Boot ROM | Socket, 32-pin JEDEC, read-write |
| Driver | Download Page |
The Intel 8∕16 LAN Adapter is a 10Mbps network card. It is notable for being compatible with the IBM PC/XT because of its dual 8-bit / 16-bit operating modes. There are several revisions of the card which have different physical interfaces at the back. Revisions include: RJ45 + dsub15, BNC + dsub15, and possibly more.
Additional photos
Underside
Alternate card (Fil-Mag)
Revision with RJ45 + dsub15 interfaces
Boot ROM
This card's boot ROM socket takes a standard 32-pin EEPROM chip, as well as 28-pin EEPROM chips such as the 28C64. It has been tested extensively with the 28C64 chip flashed with XT-IDE BIOS images, both XT and AT versions. It is a reliable way to boot from a modern era hard drive connected to an XT or AT class system whose BIOS would not natively support it.
DOS Support
The card's DOS drivers come with a configuration program (SOFTSET.EXE) that can be used to enable the ROM socket (it is disabled by default) and set the base address, as well as adjust all the usual options like the I/O address and IRQ. There is a configuration option to force 8-bit operation even while plugged into a 16-bit ISA slot. The packet driver for DOS works perfectly with the MTCP suite from FreeDOS.
