Difference between revisions of "3Com 3c509"
From Vogons Wiki
(→Additional photos) |
|||
| Line 21: | Line 21: | ||
}} | }} | ||
| − | The '''3 Com 3C509''' is a 10Mbps network card. | + | The '''3 Com 3C509''' is a 10Mbps network card from 3 Coms popular Etherlink III series. There are versions with different connector types availiable, with the Combo variant shown here is the most versatile. |
| Line 34: | Line 34: | ||
This card's boot ROM socket will take a standard 28-pin ROM chip. It has also been successfully tested with a 32-pin ROM chip using an adapter<ref>[http://sbfmdrv.blogspot.com.au/2015/11/retrofitting-new-eeprom-into-old-pc.html Port 388h - Retrofitting a new EEPROM into an old PC]</ref>. XTIDE will run without any problem. | This card's boot ROM socket will take a standard 28-pin ROM chip. It has also been successfully tested with a 32-pin ROM chip using an adapter<ref>[http://sbfmdrv.blogspot.com.au/2015/11/retrofitting-new-eeprom-into-old-pc.html Port 388h - Retrofitting a new EEPROM into an old PC]</ref>. XTIDE will run without any problem. | ||
| − | The card's DOS drivers come with a configuration program (<tt> | + | The card's DOS drivers come with a configuration program (<tt>3C50XCFG.EXE</tt>) that can be used to enable the ROM socket (it is disabled by default) and set the base address, as well as adjust all the usual options like base address and IRQ. |
| − | + | If used in an EISA board the card can be set to EISA mode by use oof the utility and later configured by the ECU. | |
== Resources == | == Resources == | ||
Revision as of 08:01, 14 March 2018
3Com 3c509
| Bus type | ISA |
|---|---|
| Bus width | 16-bit |
| Bus speed | 8 MHz |
| 8-bit ISA compatible? | Yes |
| Manufacturer | 3 Com Corporation |
| Chipset | EN50903 |
| Compatible with | NE1000, NE2000 |
| Connectors | AUI, BNC, RJ45 |
| Requires -5VDC? | No |
| Requires -12VDC? | No |
| Config method | Software |
| Ethernet | |
| Boot ROM | Socket, 28-pin JEDEC, read-only |
| Driver | Missing download URL |
The 3 Com 3C509 is a 10Mbps network card from 3 Coms popular Etherlink III series. There are versions with different connector types availiable, with the Combo variant shown here is the most versatile.
Additional photos
Underside
Boot ROM
This card's boot ROM socket will take a standard 28-pin ROM chip. It has also been successfully tested with a 32-pin ROM chip using an adapter[1]. XTIDE will run without any problem.
The card's DOS drivers come with a configuration program (3C50XCFG.EXE) that can be used to enable the ROM socket (it is disabled by default) and set the base address, as well as adjust all the usual options like base address and IRQ. If used in an EISA board the card can be set to EISA mode by use oof the utility and later configured by the ECU.
Resources
- I/O address: 0, 20, 40, ... 3A0, 3E0, then the same increments starting at 2000, 4000, 6000, 8000, A000, C000, E000.
- IRQ: 2, 3, 4, 5, 7, 10, 11, 15, Disabled.
- Boot ROM size: 16kB, 32kB, 64kB, Disabled.
- Boot ROM: 8000, 8400, 8800, 8C00, then the same increments starting at 9000, A000, B000, C000, D000, E000 and F000.
