VLB IDE Controllers
Jump to navigation
Jump to search
Full VL-bus IDE chip list
Software-configured
| Brand | Chip | Earliest FAB Date | IDE Ports | Fastest Mode | IO RDY | Internal Strobes | Config Method | MR BIOS Support | XUB Support | Commandline Parameters | Notes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| ADD2 | DW729 | Late 93 | 2 | PIO-3 | Driver | Example Parameters: D0:S/20 R/68 W/FF M/FF P/11 Dx --> x is the drive number starting a 0 S/xx --> hex sectors per transfer for the drive <=32 R/ar --> Read cycles. a = active - 1; r = recovery - 1. Example: R/68 = 9 active cycles, 7 recovery cycles W/ar --> Write cycles, same format as Read M/ar --> Other I/O cycles, same format as Read P/xx --> Bit 0: Enable read-ahead, Bit 1: Enable Post Write, Bit 2: Disable read waits, Bit 3: Disable write waits, Bit 4: Enable 32-bit transfers, Bits 5-7: Undefined. Example: P/11 means Enable read ahead and 32 bit writes /X --> Skip speed test |
Notes: Driver code is XOR-encrypted Other names: Dataworld DW729 Detection: Bases 100h-1C0h: out base,85h unlock, register 0Ah reads 41h ('A'). Genuine part: register 17h = B5hTiming registers: Registers 80h-87h at base+1 after each 85h unlockExamined: ADD_IDE.SYS 1.03 | ||||
| Appian | ADI/2 | Mid 93 | 1 | PIO-4 | Yes | Yes | Driver | 3.21 | verbose --> Prints debug output while loading floppy --> Changes chip register 0Fh (handling of port 3F7h) so the chip works alongside a floppy controller initonly --> Programs the chip but leaves the disks on the BIOS; also turns multiple mode off noinit --> Skips the chip set-up routine; the driver still loads io16 / io32 --> Forces 16-bit or 32-bit data transfers instead of auto-detecting b=n --> Bus clock period in ns: b=30 = 33 MHz, b=25 = 40 MHz, b=20 = 50 MHz c=m --> Enable multiple-sector (block) transfers for C: c=s --> Disable multiple-sector (block) transfers for C: ctime=320,320 --> set PIO 0 for Drive C: ctime=300,270 --> set PIO 1 for Drive C: ctime=210,150 --> set PIO 2 for Drive C: ctime=80,100 --> set PIO 3 for Drive C: ctime=70,50 --> set PIO 4 for Drive C: |
Notes: flexidrv.sys from Adaptec seems like the best driver. FLEXIDRV rejects the DMA options (,a) on this chip, and using one drops both drives to mode 0Other names: ALi M5213; CL-PD7220; AIC-25VL01 Detection: Ports 35h/B5h must differ from the PIC masks at 21h/A1h. Then an ID echo at 0AD4h, 34h or B4h: ID below 38h = AIC-25VL01 (38h+ is the AIC-25PC10)Timing registers: ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7-4, recovery clocks in bits 3-0. 7/12: address setup. 1: config; 13: revision Examined: FLEXIDRV.SYS 2.14 | |
| Adaptec | AIC-25PC10 | Not seen yet | Not seen yet | MWDMA-2 | Yes | Yes | Driver | 3.21 | All of the ADI/2 options, plus: c=m,a --> Multiword DMA for C: c=s,a --> Single-word DMA for C: c=a --> DMA for C:, multiword if the drive supports it, otherwise single-word ctime=60,40 --> PIO 5 timing for C:; only faster than PIO 4 at 40 or 50 MHz |
Notes: The AIC-25PC10 seems to have additional functionality. Its DMA is on the IDE cable only: the driver sends READ/WRITE DMA, but the CPU still moves the data through the data port Detection: VL-bus mode: same probe as the ADI/2, with an ID echo of 38h or higher at 0AD4h, 34h or B4h. PCI mode: Appian 1097:0038Timing registers: As the ADI/2, but the data port is a word wide. DMA timing in registers 23h/24h (drive 0) and 28h/29h (drive 1); bit 4 of 7/12 set for DMAExamined: FLEXIDRV.SYS 2.14 | |
| Atronics | IDE-2015PL | Late 94 | 2 | PIO-4 | Driver | /Dx:Px where x= 0-4. /T:25/33/40/50 picks the bus-clock table |
Notes: 2015PL.SYS /Dx:P4 Other names: DTC 803 Detection: Index E0h/data E4h, then B0h/B4h; register echo with 3F6h reads between accessesTiming registers: One register per drive through the same index/data pair. 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25-50 MHz; /T:66 reads past the tables (bug). Linux dtc2278.c writes A0h/C3h for PIO 3+ at B0h/B4hExamined: 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A | ||||
| CMD | PCI0640B | Late 94 | 2 | MWDMA-1 | Yes | Yes | Driver | 3.21 | /PIOMODE:X where x= 0-4. CMD640X.VL 2.09 uses /A<MHz>, /O<port><drive><mode>, /H |
Notes: Advanced features cause data corruption in multitasking environments. Hidden switches: /CMD, /FOO:BARDetection: Index 178h/data 17Ch (else 78h/7Ch): register 50h not 00h/FFh, bit 5 set; register 5Bh echoes BDhTiming registers: Registers 51h-58h; per-drive clocks computed from /A<MHz>Examined: CMD640X.VL 2.09 | |
| Promise | PDC-20230c | Late 93 | 1 | PIO-3 | Yes | Yes | Driver | 3.21 | Yes | 0(slow), 8 (fast), A (iordy). The PROMISE.SYS 3.3 README lists levels 0-8. Config-mode 1F3h speeds 0-7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. Levels 0-8 confirmed ; PROMISE.SYS has 9-entry tables, one per level |
Other names: VG3, TurboChip C Detection: Config-mode unlock on the IDE ports: in 1F5h, set 1F2h bit 7, in 1F2h, in 3F6h ×2, in 1F2h ×3; bit 7 reads back clear = PromiseTiming registers: Index 1F8h/data 1F9h: registers 2n/2n+1 get a word from one of four tables chosen by the measured bus speed. Register 7 = transfer status. No chip ID read; same code for every Promise chip. Four 9-entry tables (one per measured bus class), shared by all three Promise chipsExamined: PROMISE.SYS 3.3 |
| Promise | PDC-20630 | Mid 94 | 2 | WDMA2 | Yes | Yes | Driver | 3.21 | Yes | 0(slow), 8 (fast), A (iordy), M (mwdma) | Notes: READ/WRITE DMA (C8h/CAh) enables MWDMA to the chip, but data still moves to memory by PIO from 1F0h. Driver only seems to set MWDMA-1 (SET FEATURES 21h, DMA levels 7-8); it never sends 22hOther names: VG4 Detection: As PDC-20230c, then 1F4h bit 3 makes 1F8h read back its index (bits 0-2)Timing registers: 1F3h speed as PDC-20230c, plus four timing registers through 1F8h/1F9h (enabled by 1F4h bit 3)Examined: PROMISE.SYS 3.3 (same code path; no chip check) |
| QDI | Vision 6500 | Mid 93 | 1 | PIO-2 | Driver | Yes | Setup configures per drive. Driver picks a timing class from its drive table | Detection: Register 31h (or B1h): upper nibble C0h; bit 3 set = disabledTiming registers: One timing byte at 30h/B0h (active bits 0-2, recovery bits 4-7)Examined: QD6500.SYS 2.4 | |||
| QDI | Vision 6580 | Late 94 | 2 | PIO-4 | Card | Half | Driver | Yes | Setup configures per drive | Notes: PIO timing based on bus clock makes the controller less robust on some systems Detection: Register 31h (or B1h): upper nibble A0h or 50hTiming registers: As QD6500, plus secondary-channel timing Examined: QD6580.sys 3.7 | |
| SIS | 83C601 | Early 95 | 1 | PIO-4? | Yes | Yes | Driver | 3.21 | Waitstate 1 (fast) -7 (slow) | Notes: 83C601 has newer fab dates than the 83C611. Other names: Might also work as a PCI controller PCI ID 1039:0601Detection: in 1F3h; in 1F2h ×4; out 1F2h,F3h; 1F2h reads D3hTiming registers: 1F2h ← F0h + (wait state − 1) after the same unlockExamined: S134XM1.SYS 2.0, S134XD1.COM 3.5; SIS611.SYS | |
| SIS | 83C611 | Late 93 | 1 | PIO-4? | Yes | Driver | 3.21 | Wait state 0-7 for each channel | Notes: Older than the 83C601 Other names: Driver banner says "VL/PCI-IDE"; the PCI check is unused Detection: Same 1F2h sequence (0C14h)Timing registers: 1F2h: F3h, B5h, then computed wait statesExamined: SIS611.SYS 2.11 | ||
| UMC | UM8672F | Late 94 | 1 | PIO-2 | Driver | Speeds 0 (slow) -11 (fast) | Notes: PIO-4 with Modded Driver. Driver calls speed 10 the "proper speed" for Enhanced IDE drives Other names: UM82C872F Detection: None: 108h/109h unlocked with 5Ah, no ID read backTiming registers: Registers D0h-DDh through index 108h/data 109h; all set to CBh (slowest) first. Six 12-entry tables in UM8672.SYS (chip ID A0h/A2h × 3 bus-speed classes).Examined: UM8672.SYS 2.1 | ||||
| VIA | VT83C461 | Mid 94 | 2 | PIO-2 | Yes | Driver | PIO_TIME=, DMA_TIME=, SET_DMAM= |
Notes: Has a BIOS / AV140 / AV150 / AV300 Other names: Driver also covers the VT82C496G Detection: Index A8h/data A9h: register 00h upper nibble 70h/90h, register 71h bit 0 setTiming registers: Registers 71h (IDE enable), 93h (timing/mode)Examined: VIAIDE.SYS 4.02 | |||
| Winbond | W83759AF | Early 95 | 2 | PIO-3 | Yes | Yes | Driver | /D0:13 (speeds 0-13) | Notes: software speed config and "advanced mode". Measures the bus clock with the PC timer. Might support PIO 4; "A" version is software configurable Other names: DTC 2278E Rev W. Detection: Bases 4B0h/5B0h… then 430h/530h…: 63h written at base+0 reads back at base+0Ch; register 87h low nibble = revision; register 80h bit 7 setTiming registers: Index base+4, data base+8 Examined: WBIDE.EXE, DOSEIDE.SYS 2.1A (at 5B0h only)
| ||
| Micronics | MIC491 | Mid 93 | 1 | PIO-2? | BIOS Setup | IDE Speeds: Normal / Medium / Fast (register 104h = 69h / 67h / 63h) |
Notes: No driver; but a Gateway BIOS seems to set the controller speed Other names: Onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS" Detection: None. The BIOS only checks that no other IDE controller answers at 1F0hTiming registers: out 9Ch,7Fh opens ports 102h-106h; 104h = speed, 102h bit 0 = IDE onExamined: GJX30G BIOS 09-24-93 |
Jumper-configured
| Brand | Chip | Earliest FAB Date | IDE Ports | Fastest Mode | IO RDY | Config Method | Speed Settings | Notes |
|---|---|---|---|---|---|---|---|---|
| Chaintech | CT9000 | Late 93 | 1 | PIO-3 | Yes | Jumper | 0-3 | Notes: Not found yet: ct9000.zip |
| DTC | DTC 805 | Early 94 | 1 | PIO-2 | Jumper | 3.9MB/s - 7.2MB/s | Notes: DOSEIDE.SYS has no code for it; it only shows the drive's reported rate Other names: DTC 2278VL, jumpers W1-W5 Examined: DOSEIDE.SYS 2.1A | |
| GoldStar | GM82C711 | Early 93 | 1 | PIO-3 | Jumper | 0-7 | Notes: GS_DOS.SYS driver does not set timing; Not a PC Chips 82C711 Examined: GS_DOS.SYS 1.21 (driver doesn't name the chip) | |
| GoldStar | GM82C712 | Mid 95 | 1 | PIO-4 | Yes | Jumper | 0-7 | Notes: Same driver as GM82C711 Other names: CompassLab CL3202. Examined: GS_DOS.SYS 1.21 |
| Holtek | HT6560A | Late 94 | 2 | PIO-2 | Jumper | 0 (slow), 3 (fast) | Notes: Driver Not found yet | |
| Holtek | HT6560B | Early 95 | 2 | PIO-3 | Yes | Jumper + Driver | 0 (slow), 3 (fast). Driver /Dn=rt,at: recovery 2-16, active 2-15 bus clocks |
Notes: Driver allows AT:2 RT:2 Detection: 3E6h handshake: after three out 3E6h,0 / in 3E6h rounds some of bits 0-5 read back clear; on the fourth all six are setTiming registers: Four reads of 3E6h, then config byte to 3E6h and timing byte (recovery << 4 OR active) to 1F6h. Linux pata_legacy 5.15 agreesExamined: HTIDE.SYS 2.41 |
| Lion | Lion 3+ | Mid 95 | 2 | PIO-3 | Jumper + Driver | 0 (slow), 2(fast). Driver will lower speed if certain drives are detected | Notes: Driver doesn't support ECHS or LBA Detection: Config window on 1F0h/1F1h (opened by reads of 1F3h, 1F2h, 3F6h); register 5 & E0h = 60hTiming registers: Per-drive registers through the 1F0h/1F1h windowExamined: LION3.SYS | |
| OPTI | 82C611 | Early 93 | 2 | PIO-3 | Jumper | Notes: Probably programmed the same way as the 82C611A; to be tested | ||
| OPTI | 82C611A | Late 94 | 2 | PIO-3 | Card | Jumper + Driver | 0 (slow), 3 (fast). SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz | Detection: 1F3h echoes C0h; then in 1F1h ×2, out 1F2h,03h (config mode), 1F3h changes, out 1F2h,83hTiming registers: In config mode: 1F3h selects the drive bank, 1F1h = write timing, 1F6h = setup and read bank, 1F0h = read timing, 1F5h bits 0-1 = bus-clock strap. Linux pata_legacy 5.15 uses the same sequence for the 82C611AExamined: optivic.sys 1.0, opti-pio.exe, opti-set.exe |
| PiC | 1288A-125 | Late 93 | 1 | PIO-2 | Yes | Jumper | 0 (slow), 3 (fast) | Notes: No driver found Other names: VIDE-1 |
| Promise | PDC-20230b | Mid 93 | 1 | PIO-3 | Jumper | 0 (slow), 2(fast) | Notes: Works with the PROMISE.SYS 3.3 drivers. Other names: CompassLab CL3201 (fab 9314); TurboChip B Detection: Write 55h to 1F2h, read it three times back to back: a 20230-B returns 00h on the third read (Soucek; also unreached code in PROMISE.SYS at 2D3Bh). Needs the same three reads as a "VLB sync" before 32-bit I/OExamined: PROMISE.SYS 3.3 | |
| UMC | UM82C871F | Mid 93 | 1 | PIO-3 | Jumper | Best speed: AT:3 RT:4 | Notes: Driver only uses standard IDE commands; its F5 setup toggles multi-sector mode Examined: UM82C871F.SYS | |
| UMC | UM85C418F | Late 93 | 1 | PIO-2 | Jumper | Best speed: AT:5 RT:9 | Notes: Combo IDE & VGA controller; The driver writes register D1h when certain drives are detected. Stability issues at fastest speedsDetection: None: 108h/109h unlocked with 5Ah, no ID read backTiming registers: Register D1h through index 108h/data 109h (one value for both drives)Examined: UM85C418F.SYS 1.07 | |
| Winbond | W83759F | Early 94 | 2 | PIO-2 | Jumper | 600ns, 500ns, 400ns, 240ns | Notes: winbond_port (Linux pata_legacy parameter; default base 130h, alternate 1B0h)Detection: Same probe as the W83759AF? WBIDE reads a revision letter; DOSEIDE needs revision B or later. Linux only programs the W83759A, after turning off jumper mode (register 81h bit 7).
|
No configuration
No driver or setup utility has been found for these chips.
| Brand | Chip | Earliest FAB Date | IDE Ports | Notes |
|---|---|---|---|---|
| QDI | Vision 5500 | N/A | 1 | The existence of this chip was inferred by the existence of a QDI5500 VLB IDE controller in the TH99 repository. No photos found. |
| Tans | TS8310 | Mid 94 | 2 | References to ts8310.zip exist on BBS sites, but no uncorrupted versions exist. TANS BIOS files have been found but are controller agnostic. Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997) SIIG v3.10, which resembles v2.00 with a name change TANS "Enhance IDE driver" v2.10 ">8.4GB" (1999) All use only the standard IDE ports at 1F0h/170h/1E8h/168h: No chip detection, no timing writes, and 16-bit rep insw/outsw only (no 32-bit I/O)
|
| Tans | TS8310A | Late 94 | 2 | Same as above |
| Mach Speed | GTK6189 | Early 94 | 1 | No driver found. Frequently found paired with a Cirrus CL-GD5428 VGA; The 40-pin IDE header has never been seen fitted, some traces run to the VGA chip. The card ROM is a standard Cirrus VGA BIOS with nothing about IDE. Jumper positions are unpopulated except one that is hard-shorted, probably to disable the IDE function. Possibly IDE functionality was dropped late in the design |
| Opus | Op VIC1 | Late 93 | 1 | No driver found. "Op VIC" = Opus Vesa Ide Controller ? |
| Opus | Op VIC3 | Early 94 | 2 | No driver found. "Op VIC" = Opus Vesa Ide Controller ? |