VLB IDE Controllers

From Vogons Wiki
Revision as of 18:57, 12 November 2026 by Douglar (talk | contribs) (VLB IDE Controllers)
Jump to navigation Jump to search

Full VL-bus IDE chip list

  • † marks a value that was changed or added from the code. Where it replaces a spreadsheet value, the old value is given in brackets.
  • – means nothing to record (no driver found, or the driver doesn't do it).
  • ? means not known.
  • The details behind the last three columns are in CHIP-ID.md (detection) and TIMING.md (timing registers, settings and PIO equivalents).

Software-configured

Brand Chip Date IDE Ports Fastest Mode IO RDY Internal Strobes Config Method MR BIOS Support XUB Support Speed Settings Driver Notes Other Names / Notes Detection (VL-bus) Timing registers Examined
ADD2 DW729 Late 93 2 PIO-3 Driver Setup configures per drive Driver Options: S/00 R/00 W/00 M/00 P/00. † Driver code is XOR-encrypted Dataworld DW729 Bases 100h–1C0h: out base,85h unlock, register 0Ah reads 41h ('A'). Genuine part: register 17h = B5h Registers 80h–87h at base+1 after each 85h unlock ADD_IDE.SYS 1.03
Appian ADI/2 Mid 93 1 PIO-4 Yes Yes Driver 3.21 † ctime=, dtime= (also c=, d=, s=, m=) [No flags] flexidrv.sys from Adaptec is best ALi M5213; AIC-25VL0x; CL-PD7220. † FLEXIDRV also drives the AIC-25PC10 (VL-bus or PCI) Ports 35h/B5h must differ from the PIC masks at 21h/A1h. † Then an ID echo at 0AD4h, 34h or B4h: ID 38h+ = AIC-25PC10 (VL-bus mode), lower = AIC-25VL01. The PCI 25PC10 is Appian 1097:0038 † ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7–4, recovery clocks in bits 3–0. 7/12: address setup. 1: config; 13: revision FLEXIDRV.SYS 2.14
Atronics IDE-2015PL Late 94 2 PIO-4 Driver /Dx:Px where x= 0-4. † /T:25/33/40/50 picks the bus-clock table 2015PL.SYS /Dx:P4 DTC 803 † (sticker on the 2015PL; VL DTC 2278S/D/D Plus/E/B and PCI 2130D) Index E0h/data E4h, then B0h/B4h; register echo with 3F6h reads between accesses One register per drive through the same index/data pair. † 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25–50 MHz; /T:66 reads past the tables (bug). Linux dtc2278.c writes A0h/C3h for PIO 3+ at B0h/B4h 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A
CMD PCI0640B Late 94 2 PIO-4 Yes Yes Driver 3.21 /PIOMODE:X where x= 0-4. † CMD640X.VL 2.09 uses /A<MHz>, /O<port><drive><mode>, /H Stability issues at fastest speeds. † Hidden switches /CMD, /FOO:BAR Index 178h/data 17Ch (else 78h/7Ch): register 50h not 00h/FFh, bit 5 set; register 5Bh echoes BDh Registers 51h–58h; per-drive clocks computed from /A<MHz> CMD640X.VL 2.09
Promise PDC-20230c Late 93 1 PIO-3 Yes Yes Driver 3.21 587 1(slow), 8 (fast), A (iordy). † The PROMISE.SYS 3.3 README lists levels 0–8. † Config-mode 1F3h speeds 0–7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. † Levels 0–8 confirmed (owner); PROMISE.SYS has 9-entry tables, one per level † PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (owner) † Code name VG3, TurboChip C (Soucek) † Config-mode unlock on the IDE ports: in 1F5h, set 1F2h bit 7, in 1F2h, in 3F6h ×2, in 1F2h ×3; bit 7 reads back clear = Promise Index 1F8h/data 1F9h: registers 2n/2n+1 get a word from one of four tables chosen by the measured bus speed. Register 7 = transfer status. † No chip ID read; same code for every Promise chip. † Four 9-entry tables (one per measured bus class), shared by all three Promise chips PROMISE.SYS 3.3 (PROMISE.SYS 3.3; it doesn't name the chip)
Promise PDC-20630 Mid 94 2 WDMA2 Yes Yes Driver 3.21 587 1(slow), 8 (fast), A (iordy) Internal PIO Clock. † PROMISE.SYS 3.3 issues READ/WRITE DMA (C8h/CAh) and moves the data to memory by PIO from 1F0h. † PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (owner) WDMA2 is chip-to-pata, no DMA to system RAM. † PROMISE.SYS 3.3 only ever sets the drive to multiword DMA mode 1 (SET FEATURES 21h, DMA levels 7–8); it never sends 22h † As PDC-20230c, then 1F4h bit 3 makes 1F8h read back its index (bits 0–2) † 1F3h speed as PDC-20230c, plus four timing registers through 1F8h/1F9h (enabled by 1F4h bit 3) PROMISE.SYS 3.3 (same code path; no chip check)
QDI Vision 5500 Early 1 PIO-2 Driver Setup configures per drive Not found yet: QDI5500.sys. † The only reference to this chip found so far is in TH99; Linux pata_legacy has no QD5500 support (only QD6500/6580/6580DP) – – –
QDI Vision 6500 Mid 93 1 PIO-2 Driver 587 Setup configures per drive. † Driver picks a timing class from its drive table Register 31h (or B1h): upper nibble C0h; bit 3 set = disabled One timing byte at 30h/B0h (active bits 0–2, recovery bits 4–7) QD6500.SYS 2.4
QDI Vision 6580 Late 94 2 PIO-4 Card Half Driver m Setup configures per drive PIO timing based on bus clock Register 31h (or B1h): upper nibble A0h or 50h As QD6500, plus secondary-channel timing qd6580.sys 3.7
SIS 83C601 Early 95 1 PIO-4? Yes Yes Driver 3.21 Waitstate 1 (fast) -7 (slow) Newer than the 83C611 Tyan Driver is 1995-04. Early 95 is the earliest fab date seen. † SIIG also shipped its own drivers for this chip (owner) † PCI ID 1039:0601 (SIS611.SYS 08/94 already checks for it) in 1F3h; in 1F2h ×4; out 1F2h,F3h; 1F2h reads D3h 1F2h ← F0h + (wait state − 1) after the same unlock S134XM1.SYS 2.0, S134XD1.COM 3.5 (drivers don't name the chip; wait-state range matches)
SIS 83C611 Late 93 1 PIO-4? Yes Driver 3.21 † Wait state 0–7 for each channel Older than the 83C601 † Driver banner says "VL/PCI-IDE"; the PCI check is unused Same 1F2h sequence (0C14h) 1F2h: F3h, B5h, then computed wait states SIS611.SYS 2.11
Tans TS8310 Mid 94 2 PIO-2? Driver Not found yet: ts8310.zip, BIOS was generic. † Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997), v2.10 ">8.4GB" (1999), and SIIG v3.10, which is TANS v2.00 with only the name changed (18 bytes differ). All use only the standard IDE ports at 1F0h/170h/1E8h/168h: no chip detection, no timing writes, and 16-bit rep insw/outsw only (no 32-bit I/O) – – –
Tans TS8310A Late 94 2 PIO-2? Driver Not found yet: ts8310.zip, BIOS was generic. † Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997), v2.10 ">8.4GB" (1999), and SIIG v3.10, which is TANS v2.00 with only the name changed (18 bytes differ). All use only the standard IDE ports at 1F0h/170h/1E8h/168h: no chip detection, no timing writes, and 16-bit rep insw/outsw only (no 32-bit I/O) – – –
UMC UM8672F Late 94 1 PIO-2 Driver Speeds 0 (slow) -11 (fast) PIO-4 with Modded Driver. † Driver calls speed 10 the "proper speed" for Enhanced IDE drives UM82C872F None: 108h/109h unlocked with 5Ah, no ID read back Registers D0h–DDh through index 108h/data 109h; all set to CBh (slowest) first. † Six 12-entry tables in UM8672.SYS (chip ID A0h/A2h × 3 bus-speed classes). Linux umc8672.c uses the A0h slow-bus values (UMC-supplied). See TIMING.md, "Timing tables in the drivers" UM8672.SYS 2.1
VIA VT83C461 Mid 94 2 PIO-2 Yes Driver † PIO_TIME=, DMA_TIME=, SET_DMAM= Has a BIOS / AV140 / AV150 / AV300 † Driver also covers the VT82C496G Index A8h/data A9h: register 00h upper nibble 70h/90h, register 71h bit 0 set Registers 71h (IDE enable), 93h (timing/mode) VIAIDE.SYS 4.02
Winbond W83759AF Early 95 2 PIO-4 † (WBIDE.TXT's ns table makes speed 13 = PIO 3 at 33 MHz) Yes Yes Driver /D0:13 (speeds 0–13) software speed config and "advanced mode". † Measures the bus clock with the PC timer. † A hacked driver that enables PIO 4 is reported to exist (owner) † DTC 2278E Rev W. † F = package type; the A suggests a silicon respin (owner) Bases 4B0h/5B0h… then 430h/530h…: 63h written at base+0 reads back at base+0Ch; register 87h low nibble = revision; register 80h bit 7 set Index base+4, data base+8 WBIDE.EXE, DOSEIDE.SYS 2.1A (at 5B0h only)
Micronics MIC491 Mid 93 1 ? † BIOS Setup † IDE Speed: Normal / Medium / Fast (register 104h = 69h / 67h / 63h) † No driver; the system BIOS sets it † Onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS" † None. The BIOS only checks that no other IDE controller answers at 1F0h † out 9Ch,7Fh opens ports 102h–106h; 104h = speed, 102h bit 0 = IDE on GJX30G BIOS 09-24-93

Jumper-configured

Brand Chip Date IDE Ports Fastest Mode IO RDY Internal Strobes Config Method MR BIOS Support XUB Support Speed Settings Driver Notes Other Names / Notes Detection (VL-bus) Timing registers Examined
Chaintech CT9000 Late 93 1 PIO-3 Yes Jumper 0-3 Not found yet: ct9000.zip – – –
DTC DTC 805 Early 94 1 PIO-2 Jumper 3.9MB/s - 7.2MB/s † DOSEIDE.SYS has no code for it; it only shows the drive's reported rate † DTC 2278VL, jumpers W1–W5 – – DOSEIDE.SYS 2.1A
GoldStar GM82C711 Early 93 1 PIO-3 Jumper 0-7 † GS_DOS.SYS never writes a timing register. † The same GS_DOS.SYS works on the GM82C712 (owner) Not a PC Chips 82C711 ? – GS_DOS.SYS 1.21 (driver doesn't name the chip)
GoldStar GM82C712 Mid 95 1 PIO-4 Yes Jumper 0-7 † GS_DOS.SYS works on it too (owner) CompassLab CL3202. Not a PC Chips 82C712 ? – GS_DOS.SYS 1.21 (owner: same driver as GM82C711)
Holtek HT6560A Late 94 2 PIO-2 Jumper 0 (slow), 3 (fast) Driver Not found yet – – –
Holtek HT6560B Early 95 2 PIO-3 Yes † Jumper + Driver [Jumper] 0 (slow), 3 (fast). † Driver /Dn=rt,at: recovery 2–16, active 2–15 bus clocks Driver allows AT:2 RT:2 3E6h handshake: after three out 3E6h,0 / in 3E6h rounds some of bits 0–5 read back clear; on the fourth all six are set † Four reads of 3E6h, then config byte to 3E6h and timing byte (recovery << 4 OR active) to 1F6h [Timing bytes to 3E6h]. Linux pata_legacy 5.15 agrees HTIDE.SYS 2.41
Lion Lion 3+ Mid 95 2 PIO-3 † Jumper + Driver [Jumper] 0 (slow), 2(fast). † Driver sets a mode per drive Doesn't support ECHS or LBA Config window on 1F0h/1F1h (opened by reads of 1F3h, 1F2h, 3F6h); register 5 & E0h = 60h Per-drive registers through the 1F0h/1F1h window LION3.SYS
Mach Speed GTK6189 Early 94 1 † No driver found VLB card with a Cirrus CL-GD5428 VGA; the 40-pin IDE header has never been seen fitted, and some traces run to the VGA chip. The card ROM is a standard Cirrus VGA BIOS with nothing about IDE. Jumper positions are unpopulated except one that is hard-shorted, probably to disable the IDE function. Possibly IDE was dropped late in the design (owner's observation) – – –
Opus Op VIC1 Late 93 1 † No driver found Op VIC (VIC = Vesa Ide Controller) – – –
Opus Op VIC3 Early 94 2 Driver Op VIC (VIC = Vesa Ide Controller) – – –
OPTI 82C611 Early 93 2 PIO-3 Jumper † Probably programmed the same way as the 82C611A; to be tested (owner) Opti VIC (VIC = Vesa Ide Controller) – – –
OPTI 82C611A Late 94 2 PIO-3 Card Half † Jumper + Driver [Jumper] 0 (slow), 3 (fast). † SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz Opti VIC (VIC = Vesa Ide Controller) 1F3h echoes C0h; then in 1F1h ×2, out 1F2h,03h (config mode), 1F3h changes, out 1F2h,83h In config mode: 1F3h selects the drive bank, 1F1h = write timing, 1F6h = setup and read bank, 1F0h = read timing, 1F5h bits 0–1 = bus-clock strap. † Linux pata_legacy 5.15 uses the same sequence for the 82C611A optivic.sys 1.0, opti-pio.exe, opti-set.exe (drivers don't name the chip)
PiC 1288A-125 Late 93 1 PIO-2 Yes Jumper 0 (slow), 3 (fast) Driver Not found yet VIDE-1 – – –
Promise PDC-20230b Mid 93 1 PIO-3 Jumper 0 (slow), 2(fast) † Works with the PROMISE.SYS 3.3 drivers (owner). † PROMISE.SYS 3.3 supports it (owner) CompassLab CL3201 (9314) ? † Code name TurboChip B; jumper speeds 0, 1, 2 (Soucek) † No config mode. Write 55h to 1F2h, read it three times back to back: a 20230-B returns 00h on the third read (Soucek; also unreached code in PROMISE.SYS at 2D3Bh). Needs the same three reads as a "VLB sync" before 32-bit I/O – (jumpers) PROMISE.SYS 3.3
UMC UM82C871F Mid 93 1 PIO-3 Jumper Best speed: AT:3 RT:4 † Driver only uses standard IDE commands; its F5 setup only toggles multi-sector mode – – UM82C871F.SYS
UMC UM85C418F Late 93 1 PIO-2 † Jumper; driver overrides for 28 listed drives [Jumper] Best speed: AT:5 RT:9 Combo IDE & VGA controller. † The driver writes register D1h only when every drive is in its table Stability issues at fastest speeds None: 108h/109h unlocked with 5Ah, no ID read back Register D1h through index 108h/data 109h (one value for both drives) UM85C418F.SYS 1.07
Winbond W83759F Early 94 2 PIO-2 Jumper 600ns, 500ns, 400ns, 240ns winbond_port † (Linux pata_legacy parameter; default base 130h, alternate 1B0h) † Same probe as the W83759AF? WBIDE reads a revision letter; DOSEIDE needs revision B or later. Linux only programs the W83759A, after turning off jumper mode (register 81h bit 7). † F = package type (owner) ? – –