VLB IDE Controllers

From Vogons Wiki
Revision as of 18:53, 12 November 2026 by Douglar (talk | contribs) (List of VLB IDE COntrollers)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search
  1. Full VL-bus IDE chip list

This table is the repository owner's chip spreadsheet, merged with what the disassembly in this repo found. The first 13 columns follow the spreadsheet. The last three are new: how the driver or BIOS detects the chip, where the timing is written, and which file in this repo was examined.

- **†** marks a value that was changed or added from the code. Where it

 replaces a spreadsheet value, the old value is given in brackets.

- **–** means nothing to record (no driver found, or the driver doesn't do it). - **?** means not known. - The details behind the last three columns are in [CHIP-ID.md](CHIP-ID.md)

 (detection) and [TIMING.md](TIMING.md) (timing registers, settings and PIO
 equivalents).
    1. Software-configured

| Brand | Chip | Date | IDE Ports | Fastest Mode | IO RDY | Internal Strobes | Config Method | MR BIOS Support | XUB Support | Speed Settings | Driver Notes | Other Names / Notes | Detection (VL-bus) | Timing registers | Examined | |---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---| | ADD2 | DW729 | Late 93 | 2 | PIO-3 | | | Driver | | | Setup configures per drive | Driver Options: S/00 R/00 W/00 M/00 P/00. † Driver code is XOR-encrypted | Dataworld DW729 | Bases `100h`–`1C0h`: `out base,85h` unlock, register `0Ah` reads `41h` ('A'). Genuine part: register `17h` = `B5h` | Registers `80h`–`87h` at base+1 after each `85h` unlock | [ADD_IDE.SYS 1.03](../targets/dataworld-add_ide-sys-1.03/) | | Appian | ADI/2 | Mid 93 | 1 | PIO-4 | Yes | Yes | Driver | 3.21 | | † `ctime=`, `dtime=` (also `c=`, `d=`, `s=`, `m=`) [No flags] | flexidrv.sys from Adaptec is best | ALi M5213; AIC-25VL0x; CL-PD7220. † FLEXIDRV also drives the AIC-25PC10 (VL-bus or PCI) | Ports `35h`/`B5h` must differ from the PIC masks at `21h`/`A1h`. † Then an ID echo at `0AD4h`, `34h` or `B4h`: ID `38h`+ = AIC-25PC10 (VL-bus mode), lower = AIC-25VL01. The PCI 25PC10 is Appian `1097:0038` | † ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7–4, recovery clocks in bits 3–0. 7/12: address setup. 1: config; 13: revision | [FLEXIDRV.SYS 2.14](../targets/adaptec-flexidrv-2.14/) | | Atronics | IDE-2015PL | Late 94 | 2 | PIO-4 | | | Driver | | | /Dx:Px where x= 0-4. † `/T:25/33/40/50` picks the bus-clock table | 2015PL.SYS /Dx:P4 | DTC 803 † (sticker on the 2015PL; VL DTC 2278S/D/D Plus/E/B and PCI 2130D) | Index `E0h`/data `E4h`, then `B0h`/`B4h`; register echo with `3F6h` reads between accesses | One register per drive through the same index/data pair. † 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25–50 MHz; `/T:66` reads past the tables (bug). Linux `dtc2278.c` writes `A0h`/`C3h` for PIO 3+ at `B0h`/`B4h` | [2015PL.SYS 3.27](../targets/atronics-2015pl-sys-3.27/), [DOSEIDE.SYS 2.1A](../targets/dtc-doseide-2.1a/) | | CMD | PCI0640B | Late 94 | 2 | PIO-4 | Yes | Yes | Driver | 3.21 | | /PIOMODE:X where x= 0-4. † CMD640X.VL 2.09 uses `/A<MHz>`, `/O<port><drive><mode>`, `/H` | Stability issues at fastest speeds. † Hidden switches `/CMD`, `/FOO:BAR` | | Index `178h`/data `17Ch` (else `78h`/`7Ch`): register `50h` not `00h`/`FFh`, bit 5 set; register `5Bh` echoes `BDh` | Registers `51h`–`58h`; per-drive clocks computed from `/A<MHz>` | [CMD640X.VL 2.09](../targets/cmd-cmd640x-vl-2.09/) | | Promise | PDC-20230c | Late 93 | 1 | PIO-3 | Yes | Yes | Driver | 3.21 | 587 | 1(slow), 8 (fast), A (iordy). † The PROMISE.SYS 3.3 README lists levels 0–8. † Config-mode `1F3h` speeds 0–7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. † Levels 0–8 confirmed (owner); PROMISE.SYS has 9-entry tables, one per level | † PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (owner) | † Code name VG3, TurboChip C (Soucek) | † Config-mode unlock on the IDE ports: `in 1F5h`, set `1F2h` bit 7, `in 1F2h`, `in 3F6h` ×2, `in 1F2h` ×3; bit 7 reads back clear = Promise | Index `1F8h`/data `1F9h`: registers 2n/2n+1 get a word from one of four tables chosen by the measured bus speed. Register 7 = transfer status. † No chip ID read; same code for every Promise chip. † Four 9-entry tables (one per measured bus class), shared by all three Promise chips | [PROMISE.SYS 3.3](../targets/promise-vg4-3.3/) (PROMISE.SYS 3.3; it doesn't name the chip) | | Promise | PDC-20630 | Mid 94 | 2 | WDMA2 | Yes | Yes | Driver | 3.21 | 587 | 1(slow), 8 (fast), A (iordy) | Internal PIO Clock. † PROMISE.SYS 3.3 issues READ/WRITE DMA (`C8h`/`CAh`) and moves the data to memory by PIO from `1F0h`. † PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (owner) | WDMA2 is chip-to-pata, no DMA to system RAM. † PROMISE.SYS 3.3 only ever sets the drive to multiword DMA **mode 1** (SET FEATURES `21h`, DMA levels 7–8); it never sends `22h` | † As PDC-20230c, then `1F4h` bit 3 makes `1F8h` read back its index (bits 0–2) | † `1F3h` speed as PDC-20230c, plus four timing registers through `1F8h`/`1F9h` (enabled by `1F4h` bit 3) | [PROMISE.SYS 3.3](../targets/promise-vg4-3.3/) (same code path; no chip check) | | QDI | Vision 5500 | Early | 1 | PIO-2 | | | Driver | | | Setup configures per drive | Not found yet: QDI5500.sys. † The only reference to this chip found so far is in TH99; Linux pata_legacy has no QD5500 support (only QD6500/6580/6580DP) | | – | – | – | | QDI | Vision 6500 | Mid 93 | 1 | PIO-2 | | | Driver | | 587 | Setup configures per drive. † Driver picks a timing class from its drive table | | | Register `31h` (or `B1h`): upper nibble `C0h`; bit 3 set = disabled | One timing byte at `30h`/`B0h` (active bits 0–2, recovery bits 4–7) | [QD6500.SYS 2.4](../targets/qdi-qd6500-2.4/) | | QDI | Vision 6580 | Late 94 | 2 | PIO-4 | Card | Half | Driver | | m | Setup configures per drive | PIO timing based on bus clock | | Register `31h` (or `B1h`): upper nibble `A0h` or `50h` | As QD6500, plus secondary-channel timing | [qd6580.sys 3.7](../targets/qdi-qd6580-3.7/) | | SIS | 83C601 | Early 95 | 1 | PIO-4? | Yes | Yes | Driver | 3.21 | | Waitstate 1 (fast) -7 (slow) | Newer than the 83C611 Tyan Driver is 1995-04. Early 95 is the earliest fab date seen. † SIIG also shipped its own drivers for this chip (owner) | † PCI ID `1039:0601` (SIS611.SYS 08/94 already checks for it) | `in 1F3h`; `in 1F2h` ×4; `out 1F2h,F3h`; `1F2h` reads `D3h` | `1F2h` ← `F0h` + (wait state − 1) after the same unlock | [S134XM1.SYS 2.0](../targets/sis-s134xm1-sys-2.0/), [S134XD1.COM 3.5](../targets/sis-s134xd1-com-3.5/) (drivers don't name the chip; wait-state range matches) | | SIS | 83C611 | Late 93 | 1 | PIO-4? | Yes | | Driver | 3.21 | | † Wait state 0–7 for each channel | Older than the 83C601 | † Driver banner says "VL/PCI-IDE"; the PCI check is unused | Same `1F2h` sequence (`0C14h`) | `1F2h`: `F3h`, `B5h`, then computed wait states | [SIS611.SYS 2.11](../targets/sis-sis611-2.11/) | | Tans | TS8310 | Mid 94 | 2 | PIO-2? | | | Driver | | | | Not found yet: ts8310.zip, BIOS was generic. † Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997), v2.10 ">8.4GB" (1999), and SIIG v3.10, which is TANS v2.00 with only the name changed (18 bytes differ). All use only the standard IDE ports at 1F0h/170h/1E8h/168h: no chip detection, no timing writes, and 16-bit `rep insw`/`outsw` only (no 32-bit I/O) | | – | – | – | | Tans | TS8310A | Late 94 | 2 | PIO-2? | | | Driver | | | | Not found yet: ts8310.zip, BIOS was generic. † Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997), v2.10 ">8.4GB" (1999), and SIIG v3.10, which is TANS v2.00 with only the name changed (18 bytes differ). All use only the standard IDE ports at 1F0h/170h/1E8h/168h: no chip detection, no timing writes, and 16-bit `rep insw`/`outsw` only (no 32-bit I/O) | | – | – | – | | UMC | UM8672F | Late 94 | 1 | PIO-2 | | | Driver | | | Speeds 0 (slow) -11 (fast) | PIO-4 with Modded Driver. † Driver calls speed 10 the "proper speed" for Enhanced IDE drives | UM82C872F | None: `108h`/`109h` unlocked with `5Ah`, no ID read back | Registers `D0h`–`DDh` through index `108h`/data `109h`; all set to `CBh` (slowest) first. † Six 12-entry tables in UM8672.SYS (chip ID `A0h`/`A2h` × 3 bus-speed classes). Linux `umc8672.c` uses the `A0h` slow-bus values (UMC-supplied). See TIMING.md, "Timing tables in the drivers" | [UM8672.SYS 2.1](../targets/umc-um8672-2.1/) | | VIA | VT83C461 | Mid 94 | 2 | PIO-2 | Yes | | Driver | | | † `PIO_TIME=`, `DMA_TIME=`, `SET_DMAM=` | Has a BIOS / AV140 / AV150 / AV300 | † Driver also covers the VT82C496G | Index `A8h`/data `A9h`: register `00h` upper nibble `70h`/`90h`, register `71h` bit 0 set | Registers `71h` (IDE enable), `93h` (timing/mode) | [VIAIDE.SYS 4.02](../targets/via-viaide-4.02/) | | Winbond | W83759AF | Early 95 | 2 | PIO-4 † (WBIDE.TXT's ns table makes speed 13 = PIO 3 at 33 MHz) | Yes | Yes | Driver | | | /D0:13 (speeds 0–13) | software speed config and "advanced mode". † Measures the bus clock with the PC timer. † A hacked driver that enables PIO 4 is reported to exist (owner) | † DTC 2278E Rev W. † F = package type; the A suggests a silicon respin (owner) | Bases `4B0h`/`5B0h`… then `430h`/`530h`…: `63h` written at base+0 reads back at base+0Ch; register `87h` low nibble = revision; register `80h` bit 7 set | Index base+4, data base+8 | [WBIDE.EXE](../targets/winbond-wbide-exe/), [DOSEIDE.SYS 2.1A](../targets/dtc-doseide-2.1a/) (at `5B0h` only) | | Micronics | MIC491 | Mid 93 | 1 | ? | | | † BIOS Setup | | | † IDE Speed: Normal / Medium / Fast (register `104h` = `69h` / `67h` / `63h`) | † No driver; the system BIOS sets it | † Onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS" | † None. The BIOS only checks that no other IDE controller answers at `1F0h` | † `out 9Ch,7Fh` opens ports `102h`–`106h`; `104h` = speed, `102h` bit 0 = IDE on | [GJX30G BIOS 09-24-93](../targets/micronics-gjx30g-bios-1993-09-24/) |

    1. Jumper-configured

| Brand | Chip | Date | IDE Ports | Fastest Mode | IO RDY | Internal Strobes | Config Method | MR BIOS Support | XUB Support | Speed Settings | Driver Notes | Other Names / Notes | Detection (VL-bus) | Timing registers | Examined | |---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---| | Chaintech | CT9000 | Late 93 | 1 | PIO-3 | Yes | | Jumper | | | 0-3 | Not found yet: ct9000.zip | | – | – | – | | DTC | DTC 805 | Early 94 | 1 | PIO-2 | | | Jumper | | | 3.9MB/s - 7.2MB/s | † DOSEIDE.SYS has no code for it; it only shows the drive's reported rate | † DTC 2278VL, jumpers W1–W5 | – | – | [DOSEIDE.SYS 2.1A](../targets/dtc-doseide-2.1a/) | | GoldStar | GM82C711 | Early 93 | 1 | PIO-3 | | | Jumper | | | 0-7 | † GS_DOS.SYS never writes a timing register. † The same GS_DOS.SYS works on the GM82C712 (owner) | Not a PC Chips 82C711 | ? | – | [GS_DOS.SYS 1.21](../targets/goldstar-gs_dos-1.21/) (driver doesn't name the chip) | | GoldStar | GM82C712 | Mid 95 | 1 | PIO-4 | Yes | | Jumper | | | 0-7 | † GS_DOS.SYS works on it too (owner) | CompassLab CL3202. Not a PC Chips 82C712 | ? | – | [GS_DOS.SYS 1.21](../targets/goldstar-gs_dos-1.21/) (owner: same driver as GM82C711) | | Holtek | HT6560A | Late 94 | 2 | PIO-2 | | | Jumper | | | 0 (slow), 3 (fast) | Driver Not found yet | | – | – | – | | Holtek | HT6560B | Early 95 | 2 | PIO-3 | Yes | | † Jumper + Driver [Jumper] | | | 0 (slow), 3 (fast). † Driver `/Dn=rt,at`: recovery 2–16, active 2–15 bus clocks | Driver allows AT:2 RT:2 | | `3E6h` handshake: after three `out 3E6h,0` / `in 3E6h` rounds some of bits 0–5 read back clear; on the fourth all six are set | † Four reads of `3E6h`, then config byte to `3E6h` and timing byte (recovery << 4 OR active) to `1F6h` [Timing bytes to `3E6h`]. Linux pata_legacy 5.15 agrees | [HTIDE.SYS 2.41](../targets/holtek-htide-2.41/) | | Lion | Lion 3+ | Mid 95 | 2 | PIO-3 | | | † Jumper + Driver [Jumper] | | | 0 (slow), 2(fast). † Driver sets a mode per drive | Doesn't support ECHS or LBA | | Config window on `1F0h`/`1F1h` (opened by reads of `1F3h`, `1F2h`, `3F6h`); register 5 & `E0h` = `60h` | Per-drive registers through the `1F0h`/`1F1h` window | [LION3.SYS](../targets/lion3-lion3/) | | Mach Speed | GTK6189 | Early 94 | 1 | | | | | | | | † No driver found | VLB card with a Cirrus CL-GD5428 VGA; the 40-pin IDE header has never been seen fitted, and some traces run to the VGA chip. The card ROM is a standard Cirrus VGA BIOS with nothing about IDE. Jumper positions are unpopulated except one that is hard-shorted, probably to disable the IDE function. Possibly IDE was dropped late in the design (owner's observation) | – | – | – | | Opus | Op VIC1 | Late 93 | 1 | | | | | | | | † No driver found | Op VIC (VIC = Vesa Ide Controller) | – | – | – | | Opus | Op VIC3 | Early 94 | 2 | | | | Driver | | | | | Op VIC (VIC = Vesa Ide Controller) | – | – | – | | OPTI | 82C611 | Early 93 | 2 | PIO-3 | | | Jumper | | | | † Probably programmed the same way as the 82C611A; to be tested (owner) | Opti VIC (VIC = Vesa Ide Controller) | – | – | – | | OPTI | 82C611A | Late 94 | 2 | PIO-3 | Card | Half | † Jumper + Driver [Jumper] | | | 0 (slow), 3 (fast). † SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz | | Opti VIC (VIC = Vesa Ide Controller) | `1F3h` echoes `C0h`; then `in 1F1h` ×2, `out 1F2h,03h` (config mode), `1F3h` changes, `out 1F2h,83h` | In config mode: `1F3h` selects the drive bank, `1F1h` = write timing, `1F6h` = setup and read bank, `1F0h` = read timing, `1F5h` bits 0–1 = bus-clock strap. † Linux pata_legacy 5.15 uses the same sequence for the 82C611A | [optivic.sys 1.0](../targets/opti-optivic-1.0/), [opti-pio.exe](../targets/opti-pio-exe/), [opti-set.exe](../targets/opti-set-exe/) (drivers don't name the chip) | | PiC | 1288A-125 | Late 93 | 1 | PIO-2 | Yes | | Jumper | | | 0 (slow), 3 (fast) | Driver Not found yet | VIDE-1 | – | – | – | | Promise | PDC-20230b | Mid 93 | 1 | PIO-3 | | | Jumper | | | 0 (slow), 2(fast) | † Works with the PROMISE.SYS 3.3 drivers (owner). † PROMISE.SYS 3.3 supports it (owner) | CompassLab CL3201 (9314) ? † Code name TurboChip B; jumper speeds 0, 1, 2 (Soucek) | † No config mode. Write `55h` to `1F2h`, read it three times back to back: a 20230-B returns `00h` on the third read (Soucek; also unreached code in PROMISE.SYS at `2D3Bh`). Needs the same three reads as a "VLB sync" before 32-bit I/O | – (jumpers) | [PROMISE.SYS 3.3](../targets/promise-vg4-3.3/) | | UMC | UM82C871F | Mid 93 | 1 | PIO-3 | | | Jumper | | | Best speed: AT:3 RT:4 | † Driver only uses standard IDE commands; its F5 setup only toggles multi-sector mode | | – | – | [UM82C871F.SYS](../targets/umc-um82c871-idedrv/) | | UMC | UM85C418F | Late 93 | 1 | PIO-2 | | | † Jumper; driver overrides for 28 listed drives [Jumper] | | | Best speed: AT:5 RT:9 | Combo IDE & VGA controller. † The driver writes register `D1h` only when every drive is in its table | Stability issues at fastest speeds | None: `108h`/`109h` unlocked with `5Ah`, no ID read back | Register `D1h` through index `108h`/data `109h` (one value for both drives) | [UM85C418F.SYS 1.07](../targets/umc-um82c418-idedrv-1.07/) | | Winbond | W83759F | Early 94 | 2 | PIO-2 | | | Jumper | | | 600ns, 500ns, 400ns, 240ns | winbond_port † (Linux pata_legacy parameter; default base `130h`, alternate `1B0h`) | † Same probe as the W83759AF? WBIDE reads a revision letter; DOSEIDE needs revision B or later. Linux only programs the W83759A, after turning off jumper mode (register `81h` bit 7). † F = package type (owner) | ? | – | – |