VLB IDE Controllers: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
== Software-configured == | == Software-configured == | ||
Fastest Speed: the best whole-test averages of IDETEST's raw read and write seen so far, from separate runs, on Douglar's Am5x86-133 board (33 MHz VL-bus) with a CompactFlash card or a SATA SSD (2026-11-16 logs). Blank = not tested yet. | |||
{| class="wikitable sortable" | {| class="wikitable sortable" | ||
! | ! Controller !! Config Method !! Attributes !! Fastest Speed !! RomSupport !! Commandline Parameters !! Notes | ||
|- | |||
| ADD2 DW729<br />FAB: Late 93 || Driver || Ports: 2<br />Fastest: PIO-3 || Read 6687 / Write 5482 KB/s || || Example Parameters: D0:S/20 R/68 W/FF M/FF P/11<br />Dx --> x is the drive number starting a 0<br />S/xx --> hex sectors per transfer for the drive <=32<br />R/ar --> Read cycles. a = active - 1; r = recovery - 1. Example: R/68 = 9 active cycles, 7 recovery cycles<br />W/ar --> Write cycles, same format as Read<br />M/ar --> Other I/O cycles, same format as Read<br />P/xx --> Bit 0: Enable read-ahead, Bit 1: Enable Post Write, Bit 2: Disable read waits, Bit 3: Disable write waits, Bit 4: Enable 32-bit transfers, Bits 5-7: Undefined. Example: P/11 means Enable read ahead and 32 bit writes<br />/X --> Skip speed test || '''Notes:''' Driver code is XOR-encrypted<br />'''Other names:''' Dataworld DW729<br />'''Detection:''' Bases <code>100h</code>-<code>1C0h</code>: <code>out base,85h</code> unlock, register <code>0Ah</code> reads <code>41h</code> ('A'). Genuine part: register <code>17h</code> = <code>B5h</code><br />'''Timing registers:''' Registers <code>80h</code>-<code>87h</code> at base+1 after each <code>85h</code> unlock<br />'''Examined:''' ADD_IDE.SYS 1.03<br />'''Disk size:''' 8.4 GB limit: eCHS. Bit-shift translation of the BIOS geometry, CHS to the drive, no LBA. Drives 80h/81h only (ADD_IDE.SYS) | |||
|- | |||
| Appian ADI/2<br />FAB: Mid 93 || Driver || Ports: 1<br />Fastest: PIO-4<br />IORDY: Yes<br />Internal strobes: Yes || Read 9458 / Write 3698 KB/s || MR BIOS: 3.21 || verbose --> Prints debug output while loading<br />floppy --> Changes chip register 0Fh (handling of port 3F7h) so the chip works alongside a floppy controller<br />initonly --> Programs the chip but leaves the disks on the BIOS; also turns multiple mode off<br />noinit --> Skips the chip set-up routine; the driver still loads<br />io16 / io32 --> Forces 16-bit or 32-bit data transfers instead of auto-detecting<br />b=n --> Bus clock period in ns: b=30 = 33 MHz, b=25 = 40 MHz, b=20 = 50 MHz<br />c=m --> Enable multiple-sector (block) transfers for C:<br />c=s --> Disable multiple-sector (block) transfers for C:<br />ctime=320,320 --> set PIO 0 for Drive C:<br />ctime=300,270 --> set PIO 1 for Drive C:<br />ctime=210,150 --> set PIO 2 for Drive C:<br />ctime=80,100 --> set PIO 3 for Drive C:<br />ctime=70,50 --> set PIO 4 for Drive C: || '''Notes:''' flexidrv.sys from Adaptec seems like the best driver. FLEXIDRV rejects the DMA options (<code>,a</code>) on this chip, and using one drops both drives to mode 0<br />'''Other names:''' ALi M5213; CL-PD7220; AIC-25VL01<br />'''Detection:''' Ports <code>35h</code>/<code>B5h</code> must differ from the PIC masks at <code>21h</code>/<code>A1h</code>. Then an ID echo at <code>0AD4h</code>, <code>34h</code> or <code>B4h</code>: ID below <code>38h</code> = AIC-25VL01 (<code>38h</code>+ is the AIC-25PC10)<br />'''Timing registers:''' ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7-4, recovery clocks in bits 3-0. 7/12: address setup. 1: config; 13: revision<br />'''Examined:''' FLEXIDRV.SYS 2.14<br />'''Disk size:''' 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS, no LBA (FLEXIDRV.SYS) | |||
|- | |- | ||
| | | Adaptec AIC-25PC10<br />FAB: Not seen yet || Driver || Ports: Not seen yet<br />Fastest: MWDMA-2<br />IORDY: Yes<br />Internal strobes: Yes || || MR BIOS: 3.21 || All of the ADI/2 options, plus:<br />c=m,a --> Multiword DMA for C:<br />c=s,a --> Single-word DMA for C:<br />c=a --> DMA for C:, multiword if the drive supports it, otherwise single-word<br />ctime=60,40 --> PIO 5 timing for C:; only faster than PIO 4 at 40 or 50 MHz || '''Notes:''' The AIC-25PC10 seems to have additional functionality. Its DMA is on the IDE cable only: the driver sends READ/WRITE DMA, but the CPU still moves the data through the data port<br />'''Detection:''' VL-bus mode: same probe as the ADI/2, with an ID echo of <code>38h</code> or higher at <code>0AD4h</code>, <code>34h</code> or <code>B4h</code>. PCI mode: Appian <code>1097:0038</code><br />'''Timing registers:''' As the ADI/2, but the data port is a word wide. DMA timing in registers <code>23h</code>/<code>24h</code> (drive 0) and <code>28h</code>/<code>29h</code> (drive 1); bit 4 of 7/12 set for DMA<br />'''Examined:''' FLEXIDRV.SYS 2.14<br />'''Disk size:''' 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS, no LBA (FLEXIDRV.SYS) | ||
|- | |- | ||
| | | Atronics IDE-2015PL<br />FAB: Late 94 || Driver || Ports: 2<br />Fastest: PIO-4 || Read 6718 / Write 6199 KB/s || || /Dx:Px where x= 0-4. <code>/T:25/33/40/50</code> picks the bus-clock table || '''Notes:''' 2015PL.SYS /Dx:P4<br />'''Other names:''' DTC 803<br />'''Detection:''' Index <code>E0h</code>/data <code>E4h</code>, then <code>B0h</code>/<code>B4h</code>; register echo with <code>3F6h</code> reads between accesses<br />'''Timing registers:''' One register per drive through the same index/data pair. 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25-50 MHz; <code>/T:66</code> reads past the tables (bug). Linux <code>dtc2278.c</code> writes <code>A0h</code>/<code>C3h</code> for PIO 3+ at <code>B0h</code>/<code>B4h</code><br />'''Examined:''' 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A<br />'''Disk size:''' 8.4 GB limit: LBA for drives over 528 MB, but still addressed through CHS INT 13h calls (2015PL.SYS) | ||
|- | |- | ||
| | | CMD PCI0640B<br />FAB: Late 94 || Driver || Ports: 2<br />Fastest: MWDMA-1<br />IORDY: Yes<br />Internal strobes: Yes || Read 4509 / Write 4142 KB/s || MR BIOS: 3.21 || /PIOMODE:X where x= 0-4. CMD640X.VL 2.09 uses <code>/A<MHz></code>, <code>/O<port><drive><mode></code>, <code>/H</code> || '''Notes:''' Advanced features cause data corruption in multitasking environments.<br />Hidden switches: <code>/CMD</code>, <code>/FOO:BAR</code><br />'''Detection:''' Index <code>178h</code>/data <code>17Ch</code> (else <code>78h</code>/<code>7Ch</code>): register <code>50h</code> not <code>00h</code>/<code>FFh</code>, bit 5 set; register <code>5Bh</code> echoes <code>BDh</code><br />'''Timing registers:''' Registers <code>51h</code>-<code>58h</code>; per-drive clocks computed from <code>/A<MHz></code><br />'''Examined:''' CMD640X.VL 2.09<br />'''Disk size:''' eCHS by default (bit-shift translation), LBA with /L, 528 MB with /T. Probably about 4.2 GB in practice: each halving of the cylinders doubles a byte-sized head count, which overflows after 128 heads (CMD640X.VL) | ||
|- | |- | ||
| | | Holtek HT6560A<br />FAB: Late 94 || Jumper + Driver || Ports: 2<br />Fastest: PIO-2 || Read 6162 / Write 7382 KB/s || || 0 (slow), 3 (fast). Driver <code>/Dn=rt,at[,m]</code>: recovery 4-15, active 2-15 bus clocks per the readme; the code accepts recovery 4-17 and active 3-15 || '''Notes:''' Same driver code base as the HT6560B's HTIDE 2.41; only the detection, the config bytes and the parameter limits differ<br />'''Detection:''' <code>3E6h</code> handshake: three <code>out 3E6h,0</code> / <code>in 3E6h</code> rounds read non-zero, the fourth reads <code>00h</code><br />'''Timing registers:''' As the HT6560B: four reads of <code>3E6h</code>, config byte to <code>3E6h</code> (<code>05h</code>/<code>04h</code>; <code>07h</code> after detection), then the timing byte (recovery << 4 OR active) to <code>1F6h</code><br />'''Examined:''' HTIDE.SYS 1.80<br />'''Disk size:''' 8.4 GB limit: LBA or bit-shift eCHS, 8-bit logical head count (HTIDE.SYS 1.80) | ||
|- | |- | ||
| | | Holtek HT6560B<br />FAB: Early 95 || Jumper + Driver || Ports: 2<br />Fastest: PIO-3<br />IORDY: Yes || Read 7602 / Write 8936 KB/s || || 0 (slow), 3 (fast). Driver <code>/Dn=rt,at</code>: recovery 2-16, active 2-15 bus clocks || '''Notes:''' Driver allows AT:2 RT:2<br />'''Detection:''' <code>3E6h</code> handshake: after three <code>out 3E6h,0</code> / <code>in 3E6h</code> rounds some of bits 0-5 read back clear; on the fourth all six are set<br />'''Timing registers:''' Four reads of <code>3E6h</code>, then config byte to <code>3E6h</code> and timing byte (recovery << 4 OR active) to <code>1F6h</code>. Linux pata_legacy 5.15 agrees<br />'''Examined:''' HTIDE.SYS 2.41<br />'''Disk size:''' 8.4 GB limit: LBA or bit-shift eCHS, 8-bit logical head count (HTIDE.SYS) | ||
|- | |- | ||
| | | Lion Lion 3+<br />FAB: Mid 95 || Jumper + Driver || Ports: 2<br />Fastest: PIO-3 || Read 8619 / Write 11305 KB/s || || 0 (slow), 2(fast). Driver will lower speed if certain drives are detected || '''Notes:''' Driver doesn't support ECHS or LBA<br />'''Detection:''' Config window on <code>1F0h</code>/<code>1F1h</code> (opened by reads of <code>1F3h</code>, <code>1F2h</code>, <code>3F6h</code>); register 5 & <code>E0h</code> = <code>60h</code><br />'''Timing registers:''' Per-drive registers through the <code>1F0h</code>/<code>1F1h</code> window<br />'''Examined:''' LION3.SYS<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (LION3.SYS) | ||
|- | |- | ||
| | | OPTI 82C611<br />FAB: Early 93 || Jumper + Driver || Ports: 2<br />Fastest: PIO-3 || || || || '''Notes:''' Programmed the same way as the 82C611A, by its drivers and by VLBPIO: IDEPROBE's <code>opti</code> probe found one (2026-11-13) | ||
|- | |- | ||
| | | OPTI 82C611A<br />FAB: Late 94 || Jumper + Driver || Ports: 2<br />Fastest: PIO-3<br />IORDY: Card || Read 8408 / Write 11093 KB/s || MR BIOS: 1.60 || 0 (slow), 3 (fast). SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz || '''Notes:''' MR BIOS V1.60 for the OPTi 495XLC (build <code>OPTI4BH</code>) finds this chip at POST and programs it from its "VL-Bus IDE & Local-Bus IDE Controller Configuration" screen: External Jumper or Selectable Rate per drive, a rate in MB/S, and the LRDY wait state. See the BIOS notes<br />'''Detection:''' <code>1F3h</code> echoes <code>C0h</code>; then <code>in 1F1h</code> ×2, <code>out 1F2h,03h</code> (config mode), <code>1F3h</code> changes, <code>out 1F2h,83h</code><br />'''Timing registers:''' In config mode: <code>1F3h</code> selects the drive bank, <code>1F1h</code> = write timing, <code>1F6h</code> = setup and read bank, <code>1F0h</code> = read timing, <code>1F5h</code> bits 0-1 = bus-clock strap. Linux pata_legacy 5.15 uses the same sequence for the 82C611A<br />'''Examined:''' optivic.sys 1.0, opti-pio.exe, opti-set.exe<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (optivic.sys). opti-pio.exe doesn't hook INT 13h, so with it the BIOS sets the limit | ||
|- | |- | ||
| | | Promise PDC-20230c<br />FAB: Late 93 || Driver || Ports: 1<br />Fastest: PIO-3<br />IORDY: Yes<br />Internal strobes: Yes || Read 7001 / Write 7039 KB/s || MR BIOS: 3.21<br />XUB: Yes || 0(slow), 8 (fast), A (iordy). The PROMISE.SYS 3.3 README lists levels 0-8. Config-mode <code>1F3h</code> speeds 0-7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. Levels 0-8 confirmed ; PROMISE.SYS has 9-entry tables, one per level || '''Other names:''' VG3, TurboChip C<br />'''Detection:''' Config-mode unlock on the IDE ports: <code>in 1F5h</code>, set <code>1F2h</code> bit 7, <code>in 1F2h</code>, <code>in 3F6h</code> ×2, <code>in 1F2h</code> ×3; bit 7 reads back clear = Promise<br />'''Timing registers:''' Index <code>1F8h</code>/data <code>1F9h</code>: registers 2n/2n+1 get a word from one of four tables chosen by the measured bus speed. Register 7 = transfer status. No chip ID read; same code for every Promise chip. Four 9-entry tables (one per measured bus class), shared by all three Promise chips<br />'''Examined:''' PROMISE.SYS 3.3<br />'''Disk size:''' 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) | ||
|- | |- | ||
| | | Promise PDC-20630<br />FAB: Mid 94 || Driver || Ports: 2<br />Fastest: WDMA2<br />IORDY: Yes<br />Internal strobes: Yes || Read 4816 / Write 4605 KB/s || MR BIOS: 3.21<br />XUB: Yes || 0(slow), 8 (fast), A (iordy), M (mwdma) || '''Notes:''' READ/WRITE DMA (<code>C8h</code>/<code>CAh</code>) enables MWDMA to the chip, but data still moves to memory by PIO from <code>1F0h</code>. Driver only seems to set MWDMA-1 (SET FEATURES <code>21h</code>, DMA levels 7-8); it never sends <code>22h</code><br />'''Other names:''' VG4<br />'''Detection:''' As PDC-20230c, then <code>1F4h</code> bit 3 makes <code>1F8h</code> read back its index (bits 0-2)<br />'''Timing registers:''' <code>1F3h</code> speed as PDC-20230c, plus four timing registers through <code>1F8h</code>/<code>1F9h</code> (enabled by <code>1F4h</code> bit 3)<br />'''Examined:''' PROMISE.SYS 3.3 (same code path; no chip check)<br />'''Disk size:''' 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) | ||
|- | |- | ||
| | | QDI Vision 6500<br />FAB: Mid 93 || Driver || Ports: 1<br />Fastest: PIO-2 || Read 7645 / Write 6784 KB/s || XUB: Yes || Setup configures per drive. Driver picks a timing class from its drive table || '''Detection:''' Register <code>31h</code> (or <code>B1h</code>): upper nibble <code>C0h</code>; bit 3 set = disabled<br />'''Timing registers:''' One timing byte at <code>30h</code>/<code>B0h</code> (active bits 0-2, recovery bits 4-7)<br />'''Examined:''' QD6500.SYS 2.4<br />'''Disk size:''' Follows the BIOS. With an enhanced drive table (signature A0h at INT 41h) and an LBA drive: LBA with the BIOS's geometry, 8.4 GB limit. Otherwise 16 heads, 528 MB limit (QD6500.SYS) | ||
|- | |- | ||
| | | QDI Vision 6580<br />FAB: Late 94 || Driver || Ports: 2<br />Fastest: PIO-4<br />IORDY: Card<br />Internal strobes: Half || Read 8434 / Write 9743 KB/s || XUB: Yes || Setup configures per drive || '''Notes:''' PIO timing based on bus clock makes the controller less robust on some systems<br />'''Detection:''' Register <code>31h</code> (or <code>B1h</code>): upper nibble <code>A0h</code> or <code>50h</code><br />'''Timing registers:''' As QD6500, plus secondary-channel timing<br />'''Examined:''' QD6580.sys 3.7<br />'''Disk size:''' Follows the BIOS. With an enhanced drive table (signature A0h at INT 41h) and an LBA drive: LBA with the BIOS's geometry, 8.4 GB limit. Otherwise 16 heads, 528 MB limit (QD6580.SYS) | ||
|- | |- | ||
| | | SIS 83C601<br />FAB: Early 95 || Driver || Ports: 1<br />Fastest: PIO-4?<br />IORDY: Yes<br />Internal strobes: Yes || || MR BIOS: 3.21 || Waitstate 1 (fast) -7 (slow) || '''Notes:''' 83C601 has newer fab dates than the 83C611.<br />'''Other names:''' Might also work as a PCI controller PCI ID <code>1039:0601</code><br />'''Detection:''' <code>in 1F3h</code>; <code>in 1F2h</code> ×4; out <code>1F2h</code>,F3h; <code>1F2h</code> reads <code>D3h</code><br />'''Timing registers:''' <code>1F2h</code> ← <code>F0h</code> + (wait state − 1) after the same unlock<br />'''Examined:''' S134XM1.SYS 2.0, S134XD1.COM 3.5; SIS611.SYS<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (S134XM1.SYS, SIS611.SYS). S134XD1.COM doesn't hook INT 13h, so with it the BIOS sets the limit | ||
|- | |- | ||
| | | SIS 83C611<br />FAB: Late 93 || Driver || Ports: 1<br />Fastest: PIO-4?<br />IORDY: Yes || Read 2673 / Write 2057 KB/s || MR BIOS: 3.21 || Wait state 0-7 for each channel || '''Notes:''' Older than the 83C601<br />'''Other names:''' Driver banner says "VL/PCI-IDE"; the PCI check is unused<br />'''Detection:''' Same <code>1F2h</code> sequence (<code>0C14h</code>)<br />'''Timing registers:''' <code>1F2h</code>: <code>F3h</code>, <code>B5h</code>, then computed wait states<br />'''Examined:''' SIS611.SYS 2.11<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (SIS611.SYS) | ||
|- | |||
| SIS 85C407<br />FAB: Mid 93 || BIOS Setup || Ports: 1<br />Fastest: PIO-2? || || || IDE Speeds: Normal / Medium / Fast<br />(register <code>104h</code> = <code>69h</code> / <code>67h</code> / <code>63h</code>) || '''Notes:''' An ISA bus buffer and peripheral controller, not a dedicated VL-bus IDE controller: for IDE it acts as a dumb bus buffer. Micronics sold it rebranded as the MIC491. No driver; but a Gateway BIOS seems to set the controller speed<br />'''Other names:''' Micronics MIC491 (onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS")<br />'''Detection:''' No ID register. The BIOS only checks that no other IDE controller answers at <code>1F0h</code>. IDEPROBE's <code>sis407</code> probe looks for the companion SiS 85C461/471 chipset (Micronics MIC471/472; registers <code>50h</code>-<code>5Ah</code> at index <code>22h</code>/data <code>23h</code>) and then reads the setup window for a known speed value in <code>104h</code> (untested)<br />'''Timing registers:''' <code>out 9Ch,7Fh</code> opens ports <code>102h</code>-<code>106h</code>; <code>104h</code> = speed, <code>102h</code> bit 0 = IDE on<br />'''Examined:''' GJX30G BIOS 09-24-93<br />'''Disk size:''' Set by the system BIOS: the GJX30G code only sets the IDE speed | |||
|- | |||
| UMC UM8672F<br />FAB: Late 94 || Driver || Ports: 1<br />Fastest: PIO-2 || Read 6066 / Write 5458 KB/s || || Speeds 0 (slow) -11 (fast) || '''Notes:''' PIO-4 with Modded Driver. Driver calls speed 10 the "proper speed" for Enhanced IDE drives<br />'''Other names:''' UM82C872F<br />'''Detection:''' <code>108h</code>/<code>109h</code> unlocked with <code>5Ah</code>; register <code>D5h</code> = <code>A0h</code> or <code>A2h</code> (UM8672.SYS <code>49A8h</code>, <code>4A1Fh</code>); <code>A5h</code> locks<br />'''Timing registers:''' Registers <code>D0h</code>-<code>DDh</code> through index <code>108h</code>/data <code>109h</code>; all set to <code>CBh</code> (slowest) first. Six 12-entry tables in UM8672.SYS (chip ID <code>A0h</code>/<code>A2h</code> × 3 bus-speed classes).<br />'''Examined:''' UM8672.SYS 2.1<br />'''Disk size:''' 8.4 GB limit with its optional LBA path (8-bit head count). Its plain CHS path is 16 heads, 528 MB. What turns LBA on isn't traced (UM8672.SYS) | |||
|- | |||
| VIA VT83C461<br />FAB: Mid 94 || Driver || Ports: 2<br />Fastest: PIO-2<br />IORDY: Yes || Read 12925 / Write 10795 KB/s || || <code>/n</code> (n = 0-8): block size = the drive's maximum shifted right n times. No speed switch: timing comes from a built-in table of drive models (V1.5) || '''Notes:''' Has a BIOS / AV140 / AV150 / AV300<br />'''Detection:''' <code>03h</code> to <code>F0B4h</code> opens the config registers (index <code>F0B8h</code>, data <code>F0BCh</code>); register <code>07h</code> written with <code>FFh</code> reads back <code>03h</code>; <code>04h</code> to <code>F0B4h</code> closes them (VESA/IDE DOS DRIVER V1.5). VIAIDE.SYS 3.12 and 4.02 are VT82C496G drivers: they check index <code>A8h</code>/data <code>A9h</code> and don't find this card<br />'''Timing registers:''' Index <code>B8h</code>/data <code>BCh</code>, opened with <code>03h</code> to <code>B4h</code>. Registers <code>03h</code>/<code>04h</code> (drive 0) and <code>08h</code>/<code>09h</code> (drive 1): high nibble active clocks - 1, low nibble recovery clocks - 1, from the drive's cycle and active times in the driver's model table and the measured bus clock. A drive not in the table stays at <code>FFh</code> (slowest). Register <code>02h</code>: a block-mode nibble per drive<br />'''Examined:''' VIA DOS driver V1.5<br />'''Disk size:''' Not checked (V1.5 driver) | |||
|- | |||
| VIA VT82C496G<br />FAB: Not seen yet || Driver || Ports: 2<br />Fastest: PIO-3<br />IORDY: Yes || || || <code>PIO_TIME=</code>, <code>DMA_TIME=</code>, <code>SET_DMAM=</code>, <code>BLCKSIZE=</code>, <code>SNDCHIRQ=</code> || '''Notes:''' The IDE controller is integrated into the VIA VT82C496G (Pluto) chipset. VIA's MIO V2 card pairs a VT82C496G (first channel, <code>1Fx</code>) with a Winbond W83757 (second channel, <code>17x</code>). Not seen in hardware yet<br />'''Detection:''' Index <code>A8h</code>/data <code>A9h</code>, two <code>in E1h</code> as delay: register <code>00h</code> upper nibble <code>70h</code>/<code>90h</code>, register <code>71h</code> bit 0 set<br />'''Timing registers:''' Registers <code>71h</code> (IDE enable), <code>72h</code> (4-bit timing per drive), <code>93h</code> (timing/mode). The driver sets the drive to PIO 3 with IORDY<br />'''Examined:''' VIAIDE.SYS 4.02, VIAIDE.SYS 3.12<br />'''Disk size:''' Probably 528 MB limit: 16 heads. Sends LBA commands, but its I/O routine takes a 4-bit head and a 10-bit cylinder (VIAIDE.SYS 4.02, not fully traced) | |||
|- | |||
| Winbond W83759AF<br />FAB: Early 95 || Driver || Ports: 2<br />Fastest: PIO-3<br />IORDY: Yes<br />Internal strobes: Yes || Read 6627 / Write 5390 KB/s || || /D0:13 (speeds 0-13) || '''Notes:''' software speed config and "advanced mode". Measures the bus clock with the PC timer. Might support PIO 4; "A" version is software configurable<br />'''Other names:''' DTC 2278E Rev W.<br />'''Detection:''' Bases <code>4B0h</code>/<code>5B0h</code>… then <code>430h</code>/<code>530h</code>…: <code>63h</code> written at base+0 reads back at base+0Ch; register <code>87h</code> low nibble = revision; register <code>80h</code> bit 7 set<br />'''Timing registers:''' Index base+4, data base+8<br />'''Examined:''' WBIDE.EXE, DOSEIDE.SYS 2.1A (at <code>5B0h</code> only)<br />'''Disk size:''' 8.4 GB limit: LBA and "Large" (eCHS) modes, from the strings; not traced (WBIDE.EXE, DOSEIDE.SYS) | |||
|} | |} | ||
| Line 38: | Line 54: | ||
{| class="wikitable sortable" | {| class="wikitable sortable" | ||
! | ! Controller !! Config Method !! Attributes !! Fastest Speed !! Speed Settings !! Notes | ||
|- | |- | ||
| | | Chaintech CT9000<br />FAB: Late 93 || Jumper || Ports: 1<br />Fastest: PIO-3<br />IORDY: Yes || || 0-3 || '''Notes:''' Not found yet: ct9000.zip | ||
|- | |- | ||
| | | DTC DTC 805<br />FAB: Early 94 || Jumper || Ports: 1<br />Fastest: PIO-2 || || about 4000 - 7400 KB/s || '''Notes:''' DOSEIDE.SYS has no code for it; it only shows the drive's reported rate<br />'''Other names:''' DTC 2278VL, jumpers W1-W5<br />'''Examined:''' DOSEIDE.SYS 2.1A<br />'''Disk size:''' 8.4 GB limit: LBA or EDPT per drive, from its banner strings; not traced (DOSEIDE.SYS) | ||
|- | |- | ||
| | | GoldStar GM82C711<br />FAB: Early 93 || Jumper || Ports: 1<br />Fastest: PIO-3 || || 0-7 || '''Notes:''' GS_DOS.SYS driver does not set timing; Not a PC Chips 82C711<br />'''Detection:''' None: GS_DOS.SYS reads no chip register, only IDENTIFY and SET MULTIPLE<br />'''Examined:''' GS_DOS.SYS 1.21 (driver doesn't name the chip)<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (GS_DOS.SYS) | ||
|- | |- | ||
| | | GoldStar GM82C712<br />FAB: Mid 95 || Jumper || Ports: 1<br />Fastest: PIO-4<br />IORDY: Yes || || 0-7 || '''Notes:''' Same driver as GM82C711<br />'''Other names:''' CompassLab CL3202 (GS_DOS.SYS's device name is <code>CL32_DOS</code>).<br />'''Detection:''' None (same driver)<br />'''Examined:''' GS_DOS.SYS 1.21<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (GS_DOS.SYS) | ||
|- | |- | ||
| PiC | | PiC 1288A-125<br />FAB: Late 93 || Jumper || Ports: 1<br />Fastest: PIO-2<br />IORDY: Yes || || 0 (slow), 3 (fast) || '''Notes:''' No driver found<br />'''Other names:''' VIDE-1 | ||
|- | |- | ||
| Promise | | Promise PDC-20230b<br />FAB: Mid 93 || Jumper || Ports: 1<br />Fastest: PIO-3 || || 0 (slow), 2(fast) || '''Notes:''' Works with the PROMISE.SYS 3.3 drivers.<br />'''Other names:''' CompassLab CL3201 (fab 9314); TurboChip B<br />'''Detection:''' Write <code>55h</code> to <code>1F2h</code>, read it three times back to back: a 20230-B returns <code>00h</code> on the third read (Soucek; also unreached code in PROMISE.SYS at <code>2D3Bh</code>). Needs the same three reads as a "VLB sync" before 32-bit I/O. Didn't work on Douglar's card (2026-11-13: 55h read back three times), so IDEPROBE doesn't test for the B<br />'''Examined:''' PROMISE.SYS 3.3<br />'''Disk size:''' 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) | ||
|- | |- | ||
| UMC | | UMC UM82C871F<br />FAB: Mid 93 || Jumper || Ports: 1<br />Fastest: PIO-3 || || Best speed: AT:3 RT:4 || '''Notes:''' Driver only uses standard IDE commands; its F5 setup toggles multi-sector mode. Card BIOS: "GCW757VL VESA local bus IDE BIOS, TEST ROM FOR UM82C871" (UMC, 6/8/1993), the same code as the driver, on a "VESA SUPER I/O Card"<br />'''Detection:''' None: no chip registers. Driver and BIOS only check that a 32-bit <code>rep insd</code> IDENTIFY read matches a 16-bit one<br />'''Examined:''' UM82C871F.SYS, card BIOS (HDS.BIN)<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (UM82C871F.SYS) | ||
|- | |- | ||
| UMC | | UMC UM85C418F<br />FAB: Late 93 || Jumper || Ports: 1<br />Fastest: PIO-2 || Read 1939 / Write 1876 KB/s || Best speed: AT:5 RT:9 || '''Notes:''' Combo IDE & VGA controller; The driver writes register <code>D1h</code> when certain drives are detected. Stability issues at fastest speeds<br />'''Detection:''' None: <code>108h</code>/<code>109h</code> unlocked with <code>5Ah</code>, no ID read back<br />'''Timing registers:''' Register <code>D1h</code> through index <code>108h</code>/data <code>109h</code> (one value for both drives)<br />'''Examined:''' UM85C418F.SYS 1.07<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (UM85C418F.SYS) | ||
|- | |- | ||
| Winbond | | Winbond W83759F<br />FAB: Early 94 || Jumper || Ports: 2<br />Fastest: PIO-2 || Read 1872 / Write 1718 KB/s || 600ns, 500ns, 400ns, 240ns || '''Notes:''' Linux pata_legacy (5.10; current mainline no longer has the VL-bus chip code) lists the plain W83759 with the jumper-only chips (GoldStar, PIC, UM82C871F, PDC20230-B)<br />'''Detection:''' WBIDE.EXE takes a W83759 on the <code>base+0Ch</code> echo alone and only programs timing when register <code>80h</code> bit 7 is set; with it clear it drives the disks and leaves the timing to the jumpers. On Douglar's W83759F card WBIDE loaded but the data port stayed at 1129 ns per word, as without it (WBF-DRV.TXT, 2026-11-16), which fits that. Since 2026-11-16 IDEPROBE reports a W83759F when the echo answers with bit 7 clear; until then it dropped that case. Whether this card answers the echo is still to be seen (<code>IDEPROBE /ONLY:winbond /V</code>). Also on this card: some reads came back with bit 5 of a word set (WBF-CF4.TXT). Linux has no ID check for either chip: for the W83759A it takes a config port from its <code>winbond</code> parameter (<code>130h</code>, or <code>1B0h</code>), index port+1, data port+2, turns jumper mode off (register <code>81h</code> bit 7) and sets the top nibbles of <code>83h</code> (local control) and <code>85h</code> (programmable timing), then reads <code>81h</code> bits 0/1 for the enabled channels. WBIDE reads a revision letter; DOSEIDE needs revision B or later | ||
|} | |} | ||
== No configuration | == No configuration == | ||
No driver or setup utility has been found for these chips. | No driver or setup utility has been found for these chips. | ||
{| class="wikitable sortable" | {| class="wikitable sortable" | ||
! | ! Controller !! Attributes !! Notes | ||
|- | |- | ||
| QDI | | QDI Vision 5500<br />FAB: N/A || Ports: 1 || The existence of this chip was inferred by the existence of a QDI5500 VLB IDE controller in the TH99 repository. No photos found. | ||
|- | |- | ||
| Tans | | Tans TS8310<br />FAB: Mid 94 || Ports: 2 || References to ts8310.zip exist on BBS sites, but no uncorrupted versions exist.<br />TANS BIOS files have been found but are controller agnostic.<br />Three option ROMs from TANS cards checked:<br />TANS "Enhance IDE driver" v2.00 (1997)<br />SIIG v3.10, which resembles v2.00 with a name change<br />TANS "Enhance IDE driver" v2.10 ">8.4GB" (1999)<br />All use only the standard IDE ports at 1F0h/170h/1E8h/168h:<br />No chip detection, no timing writes, and 16-bit <code>rep insw</code>/<code>outsw</code> only (no 32-bit I/O) | ||
|- | |- | ||
| Tans | | Tans TS8310A<br />FAB: Late 94 || Ports: 2 || Same as above | ||
|- | |- | ||
| Mach Speed | | Mach Speed GTK6189<br />FAB: Early 94 || Ports: 1 || No driver found.<br />Frequently found paired with a Cirrus CL-GD5428 VGA;<br />The 40-pin IDE header has never been seen fitted, some traces run to the VGA chip.<br />The card ROM is a standard Cirrus VGA BIOS with nothing about IDE. Jumper positions are unpopulated except one that is hard-shorted, probably to disable the IDE function. Possibly IDE functionality was dropped late in the design | ||
|- | |- | ||
| Opus | | Opus Op VIC1<br />FAB: Late 93 || Ports: 1 || No driver found.<br />"Op VIC" = Opus Vesa Ide Controller ? | ||
|- | |- | ||
| Opus | | Opus Op VIC3<br />FAB: Early 94 || Ports: 2 || No driver found.<br />"Op VIC" = Opus Vesa Ide Controller ? | ||
|} | |} | ||
Latest revision as of 12:59, 16 November 2026
Full VL-bus IDE chip list
Software-configured
Fastest Speed: the best whole-test averages of IDETEST's raw read and write seen so far, from separate runs, on Douglar's Am5x86-133 board (33 MHz VL-bus) with a CompactFlash card or a SATA SSD (2026-11-16 logs). Blank = not tested yet.
| Controller | Config Method | Attributes | Fastest Speed | RomSupport | Commandline Parameters | Notes |
|---|---|---|---|---|---|---|
| ADD2 DW729 FAB: Late 93 |
Driver | Ports: 2 Fastest: PIO-3 |
Read 6687 / Write 5482 KB/s | Example Parameters: D0:S/20 R/68 W/FF M/FF P/11 Dx --> x is the drive number starting a 0 S/xx --> hex sectors per transfer for the drive <=32 R/ar --> Read cycles. a = active - 1; r = recovery - 1. Example: R/68 = 9 active cycles, 7 recovery cycles W/ar --> Write cycles, same format as Read M/ar --> Other I/O cycles, same format as Read P/xx --> Bit 0: Enable read-ahead, Bit 1: Enable Post Write, Bit 2: Disable read waits, Bit 3: Disable write waits, Bit 4: Enable 32-bit transfers, Bits 5-7: Undefined. Example: P/11 means Enable read ahead and 32 bit writes /X --> Skip speed test |
Notes: Driver code is XOR-encrypted Other names: Dataworld DW729 Detection: Bases 100h-1C0h: out base,85h unlock, register 0Ah reads 41h ('A'). Genuine part: register 17h = B5hTiming registers: Registers 80h-87h at base+1 after each 85h unlockExamined: ADD_IDE.SYS 1.03 Disk size: 8.4 GB limit: eCHS. Bit-shift translation of the BIOS geometry, CHS to the drive, no LBA. Drives 80h/81h only (ADD_IDE.SYS) | |
| Appian ADI/2 FAB: Mid 93 |
Driver | Ports: 1 Fastest: PIO-4 IORDY: Yes Internal strobes: Yes |
Read 9458 / Write 3698 KB/s | MR BIOS: 3.21 | verbose --> Prints debug output while loading floppy --> Changes chip register 0Fh (handling of port 3F7h) so the chip works alongside a floppy controller initonly --> Programs the chip but leaves the disks on the BIOS; also turns multiple mode off noinit --> Skips the chip set-up routine; the driver still loads io16 / io32 --> Forces 16-bit or 32-bit data transfers instead of auto-detecting b=n --> Bus clock period in ns: b=30 = 33 MHz, b=25 = 40 MHz, b=20 = 50 MHz c=m --> Enable multiple-sector (block) transfers for C: c=s --> Disable multiple-sector (block) transfers for C: ctime=320,320 --> set PIO 0 for Drive C: ctime=300,270 --> set PIO 1 for Drive C: ctime=210,150 --> set PIO 2 for Drive C: ctime=80,100 --> set PIO 3 for Drive C: ctime=70,50 --> set PIO 4 for Drive C: |
Notes: flexidrv.sys from Adaptec seems like the best driver. FLEXIDRV rejects the DMA options (,a) on this chip, and using one drops both drives to mode 0Other names: ALi M5213; CL-PD7220; AIC-25VL01 Detection: Ports 35h/B5h must differ from the PIC masks at 21h/A1h. Then an ID echo at 0AD4h, 34h or B4h: ID below 38h = AIC-25VL01 (38h+ is the AIC-25PC10)Timing registers: ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7-4, recovery clocks in bits 3-0. 7/12: address setup. 1: config; 13: revision Examined: FLEXIDRV.SYS 2.14 Disk size: 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS, no LBA (FLEXIDRV.SYS) |
| Adaptec AIC-25PC10 FAB: Not seen yet |
Driver | Ports: Not seen yet Fastest: MWDMA-2 IORDY: Yes Internal strobes: Yes |
MR BIOS: 3.21 | All of the ADI/2 options, plus: c=m,a --> Multiword DMA for C: c=s,a --> Single-word DMA for C: c=a --> DMA for C:, multiword if the drive supports it, otherwise single-word ctime=60,40 --> PIO 5 timing for C:; only faster than PIO 4 at 40 or 50 MHz |
Notes: The AIC-25PC10 seems to have additional functionality. Its DMA is on the IDE cable only: the driver sends READ/WRITE DMA, but the CPU still moves the data through the data port Detection: VL-bus mode: same probe as the ADI/2, with an ID echo of 38h or higher at 0AD4h, 34h or B4h. PCI mode: Appian 1097:0038Timing registers: As the ADI/2, but the data port is a word wide. DMA timing in registers 23h/24h (drive 0) and 28h/29h (drive 1); bit 4 of 7/12 set for DMAExamined: FLEXIDRV.SYS 2.14 Disk size: 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS, no LBA (FLEXIDRV.SYS) | |
| Atronics IDE-2015PL FAB: Late 94 |
Driver | Ports: 2 Fastest: PIO-4 |
Read 6718 / Write 6199 KB/s | /Dx:Px where x= 0-4. /T:25/33/40/50 picks the bus-clock table |
Notes: 2015PL.SYS /Dx:P4 Other names: DTC 803 Detection: Index E0h/data E4h, then B0h/B4h; register echo with 3F6h reads between accessesTiming registers: One register per drive through the same index/data pair. 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25-50 MHz; /T:66 reads past the tables (bug). Linux dtc2278.c writes A0h/C3h for PIO 3+ at B0h/B4hExamined: 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A Disk size: 8.4 GB limit: LBA for drives over 528 MB, but still addressed through CHS INT 13h calls (2015PL.SYS) | |
| CMD PCI0640B FAB: Late 94 |
Driver | Ports: 2 Fastest: MWDMA-1 IORDY: Yes Internal strobes: Yes |
Read 4509 / Write 4142 KB/s | MR BIOS: 3.21 | /PIOMODE:X where x= 0-4. CMD640X.VL 2.09 uses /A<MHz>, /O<port><drive><mode>, /H |
Notes: Advanced features cause data corruption in multitasking environments. Hidden switches: /CMD, /FOO:BARDetection: Index 178h/data 17Ch (else 78h/7Ch): register 50h not 00h/FFh, bit 5 set; register 5Bh echoes BDhTiming registers: Registers 51h-58h; per-drive clocks computed from /A<MHz>Examined: CMD640X.VL 2.09 Disk size: eCHS by default (bit-shift translation), LBA with /L, 528 MB with /T. Probably about 4.2 GB in practice: each halving of the cylinders doubles a byte-sized head count, which overflows after 128 heads (CMD640X.VL) |
| Holtek HT6560A FAB: Late 94 |
Jumper + Driver | Ports: 2 Fastest: PIO-2 |
Read 6162 / Write 7382 KB/s | 0 (slow), 3 (fast). Driver /Dn=rt,at[,m]: recovery 4-15, active 2-15 bus clocks per the readme; the code accepts recovery 4-17 and active 3-15 |
Notes: Same driver code base as the HT6560B's HTIDE 2.41; only the detection, the config bytes and the parameter limits differ Detection: 3E6h handshake: three out 3E6h,0 / in 3E6h rounds read non-zero, the fourth reads 00hTiming registers: As the HT6560B: four reads of 3E6h, config byte to 3E6h (05h/04h; 07h after detection), then the timing byte (recovery << 4 OR active) to 1F6hExamined: HTIDE.SYS 1.80 Disk size: 8.4 GB limit: LBA or bit-shift eCHS, 8-bit logical head count (HTIDE.SYS 1.80) | |
| Holtek HT6560B FAB: Early 95 |
Jumper + Driver | Ports: 2 Fastest: PIO-3 IORDY: Yes |
Read 7602 / Write 8936 KB/s | 0 (slow), 3 (fast). Driver /Dn=rt,at: recovery 2-16, active 2-15 bus clocks |
Notes: Driver allows AT:2 RT:2 Detection: 3E6h handshake: after three out 3E6h,0 / in 3E6h rounds some of bits 0-5 read back clear; on the fourth all six are setTiming registers: Four reads of 3E6h, then config byte to 3E6h and timing byte (recovery << 4 OR active) to 1F6h. Linux pata_legacy 5.15 agreesExamined: HTIDE.SYS 2.41 Disk size: 8.4 GB limit: LBA or bit-shift eCHS, 8-bit logical head count (HTIDE.SYS) | |
| Lion Lion 3+ FAB: Mid 95 |
Jumper + Driver | Ports: 2 Fastest: PIO-3 |
Read 8619 / Write 11305 KB/s | 0 (slow), 2(fast). Driver will lower speed if certain drives are detected | Notes: Driver doesn't support ECHS or LBA Detection: Config window on 1F0h/1F1h (opened by reads of 1F3h, 1F2h, 3F6h); register 5 & E0h = 60hTiming registers: Per-drive registers through the 1F0h/1F1h windowExamined: LION3.SYS Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (LION3.SYS) | |
| OPTI 82C611 FAB: Early 93 |
Jumper + Driver | Ports: 2 Fastest: PIO-3 |
Notes: Programmed the same way as the 82C611A, by its drivers and by VLBPIO: IDEPROBE's opti probe found one (2026-11-13)
| |||
| OPTI 82C611A FAB: Late 94 |
Jumper + Driver | Ports: 2 Fastest: PIO-3 IORDY: Card |
Read 8408 / Write 11093 KB/s | MR BIOS: 1.60 | 0 (slow), 3 (fast). SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz | Notes: MR BIOS V1.60 for the OPTi 495XLC (build OPTI4BH) finds this chip at POST and programs it from its "VL-Bus IDE & Local-Bus IDE Controller Configuration" screen: External Jumper or Selectable Rate per drive, a rate in MB/S, and the LRDY wait state. See the BIOS notesDetection: 1F3h echoes C0h; then in 1F1h ×2, out 1F2h,03h (config mode), 1F3h changes, out 1F2h,83hTiming registers: In config mode: 1F3h selects the drive bank, 1F1h = write timing, 1F6h = setup and read bank, 1F0h = read timing, 1F5h bits 0-1 = bus-clock strap. Linux pata_legacy 5.15 uses the same sequence for the 82C611AExamined: optivic.sys 1.0, opti-pio.exe, opti-set.exe Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (optivic.sys). opti-pio.exe doesn't hook INT 13h, so with it the BIOS sets the limit |
| Promise PDC-20230c FAB: Late 93 |
Driver | Ports: 1 Fastest: PIO-3 IORDY: Yes Internal strobes: Yes |
Read 7001 / Write 7039 KB/s | MR BIOS: 3.21 XUB: Yes |
0(slow), 8 (fast), A (iordy). The PROMISE.SYS 3.3 README lists levels 0-8. Config-mode 1F3h speeds 0-7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. Levels 0-8 confirmed ; PROMISE.SYS has 9-entry tables, one per level |
Other names: VG3, TurboChip C Detection: Config-mode unlock on the IDE ports: in 1F5h, set 1F2h bit 7, in 1F2h, in 3F6h ×2, in 1F2h ×3; bit 7 reads back clear = PromiseTiming registers: Index 1F8h/data 1F9h: registers 2n/2n+1 get a word from one of four tables chosen by the measured bus speed. Register 7 = transfer status. No chip ID read; same code for every Promise chip. Four 9-entry tables (one per measured bus class), shared by all three Promise chipsExamined: PROMISE.SYS 3.3 Disk size: 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) |
| Promise PDC-20630 FAB: Mid 94 |
Driver | Ports: 2 Fastest: WDMA2 IORDY: Yes Internal strobes: Yes |
Read 4816 / Write 4605 KB/s | MR BIOS: 3.21 XUB: Yes |
0(slow), 8 (fast), A (iordy), M (mwdma) | Notes: READ/WRITE DMA (C8h/CAh) enables MWDMA to the chip, but data still moves to memory by PIO from 1F0h. Driver only seems to set MWDMA-1 (SET FEATURES 21h, DMA levels 7-8); it never sends 22hOther names: VG4 Detection: As PDC-20230c, then 1F4h bit 3 makes 1F8h read back its index (bits 0-2)Timing registers: 1F3h speed as PDC-20230c, plus four timing registers through 1F8h/1F9h (enabled by 1F4h bit 3)Examined: PROMISE.SYS 3.3 (same code path; no chip check) Disk size: 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) |
| QDI Vision 6500 FAB: Mid 93 |
Driver | Ports: 1 Fastest: PIO-2 |
Read 7645 / Write 6784 KB/s | XUB: Yes | Setup configures per drive. Driver picks a timing class from its drive table | Detection: Register 31h (or B1h): upper nibble C0h; bit 3 set = disabledTiming registers: One timing byte at 30h/B0h (active bits 0-2, recovery bits 4-7)Examined: QD6500.SYS 2.4 Disk size: Follows the BIOS. With an enhanced drive table (signature A0h at INT 41h) and an LBA drive: LBA with the BIOS's geometry, 8.4 GB limit. Otherwise 16 heads, 528 MB limit (QD6500.SYS) |
| QDI Vision 6580 FAB: Late 94 |
Driver | Ports: 2 Fastest: PIO-4 IORDY: Card Internal strobes: Half |
Read 8434 / Write 9743 KB/s | XUB: Yes | Setup configures per drive | Notes: PIO timing based on bus clock makes the controller less robust on some systems Detection: Register 31h (or B1h): upper nibble A0h or 50hTiming registers: As QD6500, plus secondary-channel timing Examined: QD6580.sys 3.7 Disk size: Follows the BIOS. With an enhanced drive table (signature A0h at INT 41h) and an LBA drive: LBA with the BIOS's geometry, 8.4 GB limit. Otherwise 16 heads, 528 MB limit (QD6580.SYS) |
| SIS 83C601 FAB: Early 95 |
Driver | Ports: 1 Fastest: PIO-4? IORDY: Yes Internal strobes: Yes |
MR BIOS: 3.21 | Waitstate 1 (fast) -7 (slow) | Notes: 83C601 has newer fab dates than the 83C611. Other names: Might also work as a PCI controller PCI ID 1039:0601Detection: in 1F3h; in 1F2h ×4; out 1F2h,F3h; 1F2h reads D3hTiming registers: 1F2h ← F0h + (wait state − 1) after the same unlockExamined: S134XM1.SYS 2.0, S134XD1.COM 3.5; SIS611.SYS Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (S134XM1.SYS, SIS611.SYS). S134XD1.COM doesn't hook INT 13h, so with it the BIOS sets the limit | |
| SIS 83C611 FAB: Late 93 |
Driver | Ports: 1 Fastest: PIO-4? IORDY: Yes |
Read 2673 / Write 2057 KB/s | MR BIOS: 3.21 | Wait state 0-7 for each channel | Notes: Older than the 83C601 Other names: Driver banner says "VL/PCI-IDE"; the PCI check is unused Detection: Same 1F2h sequence (0C14h)Timing registers: 1F2h: F3h, B5h, then computed wait statesExamined: SIS611.SYS 2.11 Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (SIS611.SYS) |
| SIS 85C407 FAB: Mid 93 |
BIOS Setup | Ports: 1 Fastest: PIO-2? |
IDE Speeds: Normal / Medium / Fast (register 104h = 69h / 67h / 63h) |
Notes: An ISA bus buffer and peripheral controller, not a dedicated VL-bus IDE controller: for IDE it acts as a dumb bus buffer. Micronics sold it rebranded as the MIC491. No driver; but a Gateway BIOS seems to set the controller speed Other names: Micronics MIC491 (onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS") Detection: No ID register. The BIOS only checks that no other IDE controller answers at 1F0h. IDEPROBE's sis407 probe looks for the companion SiS 85C461/471 chipset (Micronics MIC471/472; registers 50h-5Ah at index 22h/data 23h) and then reads the setup window for a known speed value in 104h (untested)Timing registers: out 9Ch,7Fh opens ports 102h-106h; 104h = speed, 102h bit 0 = IDE onExamined: GJX30G BIOS 09-24-93 Disk size: Set by the system BIOS: the GJX30G code only sets the IDE speed | ||
| UMC UM8672F FAB: Late 94 |
Driver | Ports: 1 Fastest: PIO-2 |
Read 6066 / Write 5458 KB/s | Speeds 0 (slow) -11 (fast) | Notes: PIO-4 with Modded Driver. Driver calls speed 10 the "proper speed" for Enhanced IDE drives Other names: UM82C872F Detection: 108h/109h unlocked with 5Ah; register D5h = A0h or A2h (UM8672.SYS 49A8h, 4A1Fh); A5h locksTiming registers: Registers D0h-DDh through index 108h/data 109h; all set to CBh (slowest) first. Six 12-entry tables in UM8672.SYS (chip ID A0h/A2h × 3 bus-speed classes).Examined: UM8672.SYS 2.1 Disk size: 8.4 GB limit with its optional LBA path (8-bit head count). Its plain CHS path is 16 heads, 528 MB. What turns LBA on isn't traced (UM8672.SYS) | |
| VIA VT83C461 FAB: Mid 94 |
Driver | Ports: 2 Fastest: PIO-2 IORDY: Yes |
Read 12925 / Write 10795 KB/s | /n (n = 0-8): block size = the drive's maximum shifted right n times. No speed switch: timing comes from a built-in table of drive models (V1.5) |
Notes: Has a BIOS / AV140 / AV150 / AV300 Detection: 03h to F0B4h opens the config registers (index F0B8h, data F0BCh); register 07h written with FFh reads back 03h; 04h to F0B4h closes them (VESA/IDE DOS DRIVER V1.5). VIAIDE.SYS 3.12 and 4.02 are VT82C496G drivers: they check index A8h/data A9h and don't find this cardTiming registers: Index B8h/data BCh, opened with 03h to B4h. Registers 03h/04h (drive 0) and 08h/09h (drive 1): high nibble active clocks - 1, low nibble recovery clocks - 1, from the drive's cycle and active times in the driver's model table and the measured bus clock. A drive not in the table stays at FFh (slowest). Register 02h: a block-mode nibble per driveExamined: VIA DOS driver V1.5 Disk size: Not checked (V1.5 driver) | |
| VIA VT82C496G FAB: Not seen yet |
Driver | Ports: 2 Fastest: PIO-3 IORDY: Yes |
PIO_TIME=, DMA_TIME=, SET_DMAM=, BLCKSIZE=, SNDCHIRQ= |
Notes: The IDE controller is integrated into the VIA VT82C496G (Pluto) chipset. VIA's MIO V2 card pairs a VT82C496G (first channel, 1Fx) with a Winbond W83757 (second channel, 17x). Not seen in hardware yetDetection: Index A8h/data A9h, two in E1h as delay: register 00h upper nibble 70h/90h, register 71h bit 0 setTiming registers: Registers 71h (IDE enable), 72h (4-bit timing per drive), 93h (timing/mode). The driver sets the drive to PIO 3 with IORDYExamined: VIAIDE.SYS 4.02, VIAIDE.SYS 3.12 Disk size: Probably 528 MB limit: 16 heads. Sends LBA commands, but its I/O routine takes a 4-bit head and a 10-bit cylinder (VIAIDE.SYS 4.02, not fully traced) | ||
| Winbond W83759AF FAB: Early 95 |
Driver | Ports: 2 Fastest: PIO-3 IORDY: Yes Internal strobes: Yes |
Read 6627 / Write 5390 KB/s | /D0:13 (speeds 0-13) | Notes: software speed config and "advanced mode". Measures the bus clock with the PC timer. Might support PIO 4; "A" version is software configurable Other names: DTC 2278E Rev W. Detection: Bases 4B0h/5B0h… then 430h/530h…: 63h written at base+0 reads back at base+0Ch; register 87h low nibble = revision; register 80h bit 7 setTiming registers: Index base+4, data base+8 Examined: WBIDE.EXE, DOSEIDE.SYS 2.1A (at 5B0h only)Disk size: 8.4 GB limit: LBA and "Large" (eCHS) modes, from the strings; not traced (WBIDE.EXE, DOSEIDE.SYS) |
Jumper-configured
| Controller | Config Method | Attributes | Fastest Speed | Speed Settings | Notes |
|---|---|---|---|---|---|
| Chaintech CT9000 FAB: Late 93 |
Jumper | Ports: 1 Fastest: PIO-3 IORDY: Yes |
0-3 | Notes: Not found yet: ct9000.zip | |
| DTC DTC 805 FAB: Early 94 |
Jumper | Ports: 1 Fastest: PIO-2 |
about 4000 - 7400 KB/s | Notes: DOSEIDE.SYS has no code for it; it only shows the drive's reported rate Other names: DTC 2278VL, jumpers W1-W5 Examined: DOSEIDE.SYS 2.1A Disk size: 8.4 GB limit: LBA or EDPT per drive, from its banner strings; not traced (DOSEIDE.SYS) | |
| GoldStar GM82C711 FAB: Early 93 |
Jumper | Ports: 1 Fastest: PIO-3 |
0-7 | Notes: GS_DOS.SYS driver does not set timing; Not a PC Chips 82C711 Detection: None: GS_DOS.SYS reads no chip register, only IDENTIFY and SET MULTIPLE Examined: GS_DOS.SYS 1.21 (driver doesn't name the chip) Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (GS_DOS.SYS) | |
| GoldStar GM82C712 FAB: Mid 95 |
Jumper | Ports: 1 Fastest: PIO-4 IORDY: Yes |
0-7 | Notes: Same driver as GM82C711 Other names: CompassLab CL3202 (GS_DOS.SYS's device name is CL32_DOS).Detection: None (same driver) Examined: GS_DOS.SYS 1.21 Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (GS_DOS.SYS) | |
| PiC 1288A-125 FAB: Late 93 |
Jumper | Ports: 1 Fastest: PIO-2 IORDY: Yes |
0 (slow), 3 (fast) | Notes: No driver found Other names: VIDE-1 | |
| Promise PDC-20230b FAB: Mid 93 |
Jumper | Ports: 1 Fastest: PIO-3 |
0 (slow), 2(fast) | Notes: Works with the PROMISE.SYS 3.3 drivers. Other names: CompassLab CL3201 (fab 9314); TurboChip B Detection: Write 55h to 1F2h, read it three times back to back: a 20230-B returns 00h on the third read (Soucek; also unreached code in PROMISE.SYS at 2D3Bh). Needs the same three reads as a "VLB sync" before 32-bit I/O. Didn't work on Douglar's card (2026-11-13: 55h read back three times), so IDEPROBE doesn't test for the BExamined: PROMISE.SYS 3.3 Disk size: 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) | |
| UMC UM82C871F FAB: Mid 93 |
Jumper | Ports: 1 Fastest: PIO-3 |
Best speed: AT:3 RT:4 | Notes: Driver only uses standard IDE commands; its F5 setup toggles multi-sector mode. Card BIOS: "GCW757VL VESA local bus IDE BIOS, TEST ROM FOR UM82C871" (UMC, 6/8/1993), the same code as the driver, on a "VESA SUPER I/O Card" Detection: None: no chip registers. Driver and BIOS only check that a 32-bit rep insd IDENTIFY read matches a 16-bit oneExamined: UM82C871F.SYS, card BIOS (HDS.BIN) Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (UM82C871F.SYS) | |
| UMC UM85C418F FAB: Late 93 |
Jumper | Ports: 1 Fastest: PIO-2 |
Read 1939 / Write 1876 KB/s | Best speed: AT:5 RT:9 | Notes: Combo IDE & VGA controller; The driver writes register D1h when certain drives are detected. Stability issues at fastest speedsDetection: None: 108h/109h unlocked with 5Ah, no ID read backTiming registers: Register D1h through index 108h/data 109h (one value for both drives)Examined: UM85C418F.SYS 1.07 Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (UM85C418F.SYS) |
| Winbond W83759F FAB: Early 94 |
Jumper | Ports: 2 Fastest: PIO-2 |
Read 1872 / Write 1718 KB/s | 600ns, 500ns, 400ns, 240ns | Notes: Linux pata_legacy (5.10; current mainline no longer has the VL-bus chip code) lists the plain W83759 with the jumper-only chips (GoldStar, PIC, UM82C871F, PDC20230-B) Detection: WBIDE.EXE takes a W83759 on the base+0Ch echo alone and only programs timing when register 80h bit 7 is set; with it clear it drives the disks and leaves the timing to the jumpers. On Douglar's W83759F card WBIDE loaded but the data port stayed at 1129 ns per word, as without it (WBF-DRV.TXT, 2026-11-16), which fits that. Since 2026-11-16 IDEPROBE reports a W83759F when the echo answers with bit 7 clear; until then it dropped that case. Whether this card answers the echo is still to be seen (IDEPROBE /ONLY:winbond /V). Also on this card: some reads came back with bit 5 of a word set (WBF-CF4.TXT). Linux has no ID check for either chip: for the W83759A it takes a config port from its winbond parameter (130h, or 1B0h), index port+1, data port+2, turns jumper mode off (register 81h bit 7) and sets the top nibbles of 83h (local control) and 85h (programmable timing), then reads 81h bits 0/1 for the enabled channels. WBIDE reads a revision letter; DOSEIDE needs revision B or later
|
No configuration
No driver or setup utility has been found for these chips.
| Controller | Attributes | Notes |
|---|---|---|
| QDI Vision 5500 FAB: N/A |
Ports: 1 | The existence of this chip was inferred by the existence of a QDI5500 VLB IDE controller in the TH99 repository. No photos found. |
| Tans TS8310 FAB: Mid 94 |
Ports: 2 | References to ts8310.zip exist on BBS sites, but no uncorrupted versions exist. TANS BIOS files have been found but are controller agnostic. Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997) SIIG v3.10, which resembles v2.00 with a name change TANS "Enhance IDE driver" v2.10 ">8.4GB" (1999) All use only the standard IDE ports at 1F0h/170h/1E8h/168h: No chip detection, no timing writes, and 16-bit rep insw/outsw only (no 32-bit I/O)
|
| Tans TS8310A FAB: Late 94 |
Ports: 2 | Same as above |
| Mach Speed GTK6189 FAB: Early 94 |
Ports: 1 | No driver found. Frequently found paired with a Cirrus CL-GD5428 VGA; The 40-pin IDE header has never been seen fitted, some traces run to the VGA chip. The card ROM is a standard Cirrus VGA BIOS with nothing about IDE. Jumper positions are unpopulated except one that is hard-shorted, probably to disable the IDE function. Possibly IDE functionality was dropped late in the design |
| Opus Op VIC1 FAB: Late 93 |
Ports: 1 | No driver found. "Op VIC" = Opus Vesa Ide Controller ? |
| Opus Op VIC3 FAB: Early 94 |
Ports: 2 | No driver found. "Op VIC" = Opus Vesa Ide Controller ? |