VLB IDE Controllers: Difference between revisions
Jump to navigation
Jump to search
| Line 6: | Line 6: | ||
! Brand !! Chip !! Earliest FAB Date !! IDE Ports !! Fastest Mode !! IO RDY !! Internal Strobes !! Config Method !! MR BIOS Support !! XUB Support !! Commandline Parameters !! Notes | ! Brand !! Chip !! Earliest FAB Date !! IDE Ports !! Fastest Mode !! IO RDY !! Internal Strobes !! Config Method !! MR BIOS Support !! XUB Support !! Commandline Parameters !! Notes | ||
|- | |- | ||
| ADD2 || DW729 || Late 93 || 2 || PIO-3 || || || Driver || || || Example Parameters: D0:S/20 R/68 W/FF M/FF P/11<br />Dx --> x is the drive number starting a 0<br />S/xx --> hex sectors per transfer for the drive <=32<br />R/ar --> Read cycles. a = active - 1; r = recovery - 1. Example: R/68 = 9 active cycles, 7 recovery cycles<br />W/ar --> Write cycles, same format as Read<br />M/ar --> Other I/O cycles, same format as Read<br />P/xx --> Bit 0: Enable read-ahead, Bit 1: Enable Post Write, Bit 2: Disable read waits, Bit 3: Disable write waits, Bit 4: Enable 32-bit transfers, Bits 5-7: Undefined. Example: P/11 means Enable read ahead and 32 bit writes<br />/X --> Skip speed test || '''Notes:''' Driver code is XOR-encrypted<br />'''Other names:''' Dataworld DW729<br />'''Detection:''' Bases <code>100h</code>-<code>1C0h</code>: <code>out base,85h</code> unlock, register <code>0Ah</code> reads <code>41h</code> ('A'). Genuine part: register <code>17h</code> = <code>B5h</code><br />'''Timing registers:''' Registers <code>80h</code>-<code>87h</code> at base+1 after each <code>85h</code> unlock<br />'''Examined:''' ADD_IDE.SYS 1.03 | | ADD2 || DW729 || Late 93 || 2 || PIO-3 || || || Driver || || || Example Parameters: D0:S/20 R/68 W/FF M/FF P/11<br />Dx --> x is the drive number starting a 0<br />S/xx --> hex sectors per transfer for the drive <=32<br />R/ar --> Read cycles. a = active - 1; r = recovery - 1. Example: R/68 = 9 active cycles, 7 recovery cycles<br />W/ar --> Write cycles, same format as Read<br />M/ar --> Other I/O cycles, same format as Read<br />P/xx --> Bit 0: Enable read-ahead, Bit 1: Enable Post Write, Bit 2: Disable read waits, Bit 3: Disable write waits, Bit 4: Enable 32-bit transfers, Bits 5-7: Undefined. Example: P/11 means Enable read ahead and 32 bit writes<br />/X --> Skip speed test || '''Notes:''' Driver code is XOR-encrypted<br />'''Other names:''' Dataworld DW729<br />'''Detection:''' Bases <code>100h</code>-<code>1C0h</code>: <code>out base,85h</code> unlock, register <code>0Ah</code> reads <code>41h</code> ('A'). Genuine part: register <code>17h</code> = <code>B5h</code><br />'''Timing registers:''' Registers <code>80h</code>-<code>87h</code> at base+1 after each <code>85h</code> unlock<br />'''Examined:''' ADD_IDE.SYS 1.03<br />'''Disk size:''' 8.4 GB limit: eCHS. Bit-shift translation of the BIOS geometry, CHS to the drive, no LBA. Drives 80h/81h only (ADD_IDE.SYS) | ||
|- | |- | ||
| Appian || ADI/2 || Mid 93 || 1 || PIO-4 || Yes || Yes || Driver || 3.21 || || verbose --> Prints debug output while loading<br />floppy --> Changes chip register 0Fh (handling of port 3F7h) so the chip works alongside a floppy controller<br />initonly --> Programs the chip but leaves the disks on the BIOS; also turns multiple mode off<br />noinit --> Skips the chip set-up routine; the driver still loads<br />io16 / io32 --> Forces 16-bit or 32-bit data transfers instead of auto-detecting<br />b=n --> Bus clock period in ns: b=30 = 33 MHz, b=25 = 40 MHz, b=20 = 50 MHz<br />c=m --> Enable multiple-sector (block) transfers for C:<br />c=s --> Disable multiple-sector (block) transfers for C:<br />ctime=320,320 --> set PIO 0 for Drive C:<br />ctime=300,270 --> set PIO 1 for Drive C:<br />ctime=210,150 --> set PIO 2 for Drive C:<br />ctime=80,100 --> set PIO 3 for Drive C:<br />ctime=70,50 --> set PIO 4 for Drive C: || '''Notes:''' flexidrv.sys from Adaptec seems like the best driver. FLEXIDRV rejects the DMA options (<code>,a</code>) on this chip, and using one drops both drives to mode 0<br />'''Other names:''' ALi M5213; CL-PD7220; AIC-25VL01<br />'''Detection:''' Ports <code>35h</code>/<code>B5h</code> must differ from the PIC masks at <code>21h</code>/<code>A1h</code>. Then an ID echo at <code>0AD4h</code>, <code>34h</code> or <code>B4h</code>: ID below <code>38h</code> = AIC-25VL01 (<code>38h</code>+ is the AIC-25PC10)<br />'''Timing registers:''' ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7-4, recovery clocks in bits 3-0. 7/12: address setup. 1: config; 13: revision<br />'''Examined:''' FLEXIDRV.SYS 2.14 | | Appian || ADI/2 || Mid 93 || 1 || PIO-4 || Yes || Yes || Driver || 3.21 || || verbose --> Prints debug output while loading<br />floppy --> Changes chip register 0Fh (handling of port 3F7h) so the chip works alongside a floppy controller<br />initonly --> Programs the chip but leaves the disks on the BIOS; also turns multiple mode off<br />noinit --> Skips the chip set-up routine; the driver still loads<br />io16 / io32 --> Forces 16-bit or 32-bit data transfers instead of auto-detecting<br />b=n --> Bus clock period in ns: b=30 = 33 MHz, b=25 = 40 MHz, b=20 = 50 MHz<br />c=m --> Enable multiple-sector (block) transfers for C:<br />c=s --> Disable multiple-sector (block) transfers for C:<br />ctime=320,320 --> set PIO 0 for Drive C:<br />ctime=300,270 --> set PIO 1 for Drive C:<br />ctime=210,150 --> set PIO 2 for Drive C:<br />ctime=80,100 --> set PIO 3 for Drive C:<br />ctime=70,50 --> set PIO 4 for Drive C: || '''Notes:''' flexidrv.sys from Adaptec seems like the best driver. FLEXIDRV rejects the DMA options (<code>,a</code>) on this chip, and using one drops both drives to mode 0<br />'''Other names:''' ALi M5213; CL-PD7220; AIC-25VL01<br />'''Detection:''' Ports <code>35h</code>/<code>B5h</code> must differ from the PIC masks at <code>21h</code>/<code>A1h</code>. Then an ID echo at <code>0AD4h</code>, <code>34h</code> or <code>B4h</code>: ID below <code>38h</code> = AIC-25VL01 (<code>38h</code>+ is the AIC-25PC10)<br />'''Timing registers:''' ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7-4, recovery clocks in bits 3-0. 7/12: address setup. 1: config; 13: revision<br />'''Examined:''' FLEXIDRV.SYS 2.14<br />'''Disk size:''' 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS, no LBA (FLEXIDRV.SYS) | ||
|- | |- | ||
| Adaptec || AIC-25PC10 || Not seen yet || Not seen yet || MWDMA-2 || Yes || Yes || Driver || 3.21 || || All of the ADI/2 options, plus:<br />c=m,a --> Multiword DMA for C:<br />c=s,a --> Single-word DMA for C:<br />c=a --> DMA for C:, multiword if the drive supports it, otherwise single-word<br />ctime=60,40 --> PIO 5 timing for C:; only faster than PIO 4 at 40 or 50 MHz || '''Notes:''' The AIC-25PC10 seems to have additional functionality. Its DMA is on the IDE cable only: the driver sends READ/WRITE DMA, but the CPU still moves the data through the data port<br />'''Detection:''' VL-bus mode: same probe as the ADI/2, with an ID echo of <code>38h</code> or higher at <code>0AD4h</code>, <code>34h</code> or <code>B4h</code>. PCI mode: Appian <code>1097:0038</code><br />'''Timing registers:''' As the ADI/2, but the data port is a word wide. DMA timing in registers <code>23h</code>/<code>24h</code> (drive 0) and <code>28h</code>/<code>29h</code> (drive 1); bit 4 of 7/12 set for DMA<br />'''Examined:''' FLEXIDRV.SYS 2.14 | | Adaptec || AIC-25PC10 || Not seen yet || Not seen yet || MWDMA-2 || Yes || Yes || Driver || 3.21 || || All of the ADI/2 options, plus:<br />c=m,a --> Multiword DMA for C:<br />c=s,a --> Single-word DMA for C:<br />c=a --> DMA for C:, multiword if the drive supports it, otherwise single-word<br />ctime=60,40 --> PIO 5 timing for C:; only faster than PIO 4 at 40 or 50 MHz || '''Notes:''' The AIC-25PC10 seems to have additional functionality. Its DMA is on the IDE cable only: the driver sends READ/WRITE DMA, but the CPU still moves the data through the data port<br />'''Detection:''' VL-bus mode: same probe as the ADI/2, with an ID echo of <code>38h</code> or higher at <code>0AD4h</code>, <code>34h</code> or <code>B4h</code>. PCI mode: Appian <code>1097:0038</code><br />'''Timing registers:''' As the ADI/2, but the data port is a word wide. DMA timing in registers <code>23h</code>/<code>24h</code> (drive 0) and <code>28h</code>/<code>29h</code> (drive 1); bit 4 of 7/12 set for DMA<br />'''Examined:''' FLEXIDRV.SYS 2.14<br />'''Disk size:''' 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS, no LBA (FLEXIDRV.SYS) | ||
|- | |- | ||
| Atronics || IDE-2015PL || Late 94 || 2 || PIO-4 || || || Driver || || || /Dx:Px where x= 0-4. <code>/T:25/33/40/50</code> picks the bus-clock table || '''Notes:''' 2015PL.SYS /Dx:P4<br />'''Other names:''' DTC 803<br />'''Detection:''' Index <code>E0h</code>/data <code>E4h</code>, then <code>B0h</code>/<code>B4h</code>; register echo with <code>3F6h</code> reads between accesses<br />'''Timing registers:''' One register per drive through the same index/data pair. 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25-50 MHz; <code>/T:66</code> reads past the tables (bug). Linux <code>dtc2278.c</code> writes <code>A0h</code>/<code>C3h</code> for PIO 3+ at <code>B0h</code>/<code>B4h</code><br />'''Examined:''' 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A | | Atronics || IDE-2015PL || Late 94 || 2 || PIO-4 || || || Driver || || || /Dx:Px where x= 0-4. <code>/T:25/33/40/50</code> picks the bus-clock table || '''Notes:''' 2015PL.SYS /Dx:P4<br />'''Other names:''' DTC 803<br />'''Detection:''' Index <code>E0h</code>/data <code>E4h</code>, then <code>B0h</code>/<code>B4h</code>; register echo with <code>3F6h</code> reads between accesses<br />'''Timing registers:''' One register per drive through the same index/data pair. 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25-50 MHz; <code>/T:66</code> reads past the tables (bug). Linux <code>dtc2278.c</code> writes <code>A0h</code>/<code>C3h</code> for PIO 3+ at <code>B0h</code>/<code>B4h</code><br />'''Examined:''' 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A<br />'''Disk size:''' 8.4 GB limit: LBA for drives over 528 MB, but still addressed through CHS INT 13h calls (2015PL.SYS) | ||
|- | |- | ||
| CMD || PCI0640B || Late 94 || 2 || MWDMA-1 || Yes || Yes || Driver || 3.21 || || /PIOMODE:X where x= 0-4. CMD640X.VL 2.09 uses <code>/A<MHz></code>, <code>/O<port><drive><mode></code>, <code>/H</code> || '''Notes:''' Advanced features cause data corruption in multitasking environments.<br />Hidden switches: <code>/CMD</code>, <code>/FOO:BAR</code><br />'''Detection:''' Index <code>178h</code>/data <code>17Ch</code> (else <code>78h</code>/<code>7Ch</code>): register <code>50h</code> not <code>00h</code>/<code>FFh</code>, bit 5 set; register <code>5Bh</code> echoes <code>BDh</code><br />'''Timing registers:''' Registers <code>51h</code>-<code>58h</code>; per-drive clocks computed from <code>/A<MHz></code><br />'''Examined:''' CMD640X.VL 2.09 | | CMD || PCI0640B || Late 94 || 2 || MWDMA-1 || Yes || Yes || Driver || 3.21 || || /PIOMODE:X where x= 0-4. CMD640X.VL 2.09 uses <code>/A<MHz></code>, <code>/O<port><drive><mode></code>, <code>/H</code> || '''Notes:''' Advanced features cause data corruption in multitasking environments.<br />Hidden switches: <code>/CMD</code>, <code>/FOO:BAR</code><br />'''Detection:''' Index <code>178h</code>/data <code>17Ch</code> (else <code>78h</code>/<code>7Ch</code>): register <code>50h</code> not <code>00h</code>/<code>FFh</code>, bit 5 set; register <code>5Bh</code> echoes <code>BDh</code><br />'''Timing registers:''' Registers <code>51h</code>-<code>58h</code>; per-drive clocks computed from <code>/A<MHz></code><br />'''Examined:''' CMD640X.VL 2.09<br />'''Disk size:''' eCHS by default (bit-shift translation), LBA with /L, 528 MB with /T. Probably about 4.2 GB in practice: each halving of the cylinders doubles a byte-sized head count, which overflows after 128 heads (CMD640X.VL) | ||
|- | |- | ||
| Promise || PDC-20230c || Late 93 || 1 || PIO-3 || Yes || Yes || Driver || 3.21 || Yes || 0(slow), 8 (fast), A (iordy). The PROMISE.SYS 3.3 README lists levels 0-8. Config-mode <code>1F3h</code> speeds 0-7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. Levels 0-8 confirmed ; PROMISE.SYS has 9-entry tables, one per level || '''Other names:''' VG3, TurboChip C<br />'''Detection:''' Config-mode unlock on the IDE ports: <code>in 1F5h</code>, set <code>1F2h</code> bit 7, <code>in 1F2h</code>, <code>in 3F6h</code> ×2, <code>in 1F2h</code> ×3; bit 7 reads back clear = Promise<br />'''Timing registers:''' Index <code>1F8h</code>/data <code>1F9h</code>: registers 2n/2n+1 get a word from one of four tables chosen by the measured bus speed. Register 7 = transfer status. No chip ID read; same code for every Promise chip. Four 9-entry tables (one per measured bus class), shared by all three Promise chips<br />'''Examined:''' PROMISE.SYS 3.3 | | Promise || PDC-20230c || Late 93 || 1 || PIO-3 || Yes || Yes || Driver || 3.21 || Yes || 0(slow), 8 (fast), A (iordy). The PROMISE.SYS 3.3 README lists levels 0-8. Config-mode <code>1F3h</code> speeds 0-7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. Levels 0-8 confirmed ; PROMISE.SYS has 9-entry tables, one per level || '''Other names:''' VG3, TurboChip C<br />'''Detection:''' Config-mode unlock on the IDE ports: <code>in 1F5h</code>, set <code>1F2h</code> bit 7, <code>in 1F2h</code>, <code>in 3F6h</code> ×2, <code>in 1F2h</code> ×3; bit 7 reads back clear = Promise<br />'''Timing registers:''' Index <code>1F8h</code>/data <code>1F9h</code>: registers 2n/2n+1 get a word from one of four tables chosen by the measured bus speed. Register 7 = transfer status. No chip ID read; same code for every Promise chip. Four 9-entry tables (one per measured bus class), shared by all three Promise chips<br />'''Examined:''' PROMISE.SYS 3.3<br />'''Disk size:''' 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) | ||
|- | |- | ||
| Promise || PDC-20630 || Mid 94 || 2 || WDMA2 || Yes || Yes || Driver || 3.21 || Yes || 0(slow), 8 (fast), A (iordy), M (mwdma) || '''Notes:''' READ/WRITE DMA (<code>C8h</code>/<code>CAh</code>) enables MWDMA to the chip, but data still moves to memory by PIO from <code>1F0h</code>. Driver only seems to set MWDMA-1 (SET FEATURES <code>21h</code>, DMA levels 7-8); it never sends <code>22h</code><br />'''Other names:''' VG4<br />'''Detection:''' As PDC-20230c, then <code>1F4h</code> bit 3 makes <code>1F8h</code> read back its index (bits 0-2)<br />'''Timing registers:''' <code>1F3h</code> speed as PDC-20230c, plus four timing registers through <code>1F8h</code>/<code>1F9h</code> (enabled by <code>1F4h</code> bit 3)<br />'''Examined:''' PROMISE.SYS 3.3 (same code path; no chip check) | | Promise || PDC-20630 || Mid 94 || 2 || WDMA2 || Yes || Yes || Driver || 3.21 || Yes || 0(slow), 8 (fast), A (iordy), M (mwdma) || '''Notes:''' READ/WRITE DMA (<code>C8h</code>/<code>CAh</code>) enables MWDMA to the chip, but data still moves to memory by PIO from <code>1F0h</code>. Driver only seems to set MWDMA-1 (SET FEATURES <code>21h</code>, DMA levels 7-8); it never sends <code>22h</code><br />'''Other names:''' VG4<br />'''Detection:''' As PDC-20230c, then <code>1F4h</code> bit 3 makes <code>1F8h</code> read back its index (bits 0-2)<br />'''Timing registers:''' <code>1F3h</code> speed as PDC-20230c, plus four timing registers through <code>1F8h</code>/<code>1F9h</code> (enabled by <code>1F4h</code> bit 3)<br />'''Examined:''' PROMISE.SYS 3.3 (same code path; no chip check)<br />'''Disk size:''' 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) | ||
|- | |- | ||
| QDI || Vision 6500 || Mid 93 || 1 || PIO-2 || || || Driver || || Yes || Setup configures per drive. Driver picks a timing class from its drive table || '''Detection:''' Register <code>31h</code> (or <code>B1h</code>): upper nibble <code>C0h</code>; bit 3 set = disabled<br />'''Timing registers:''' One timing byte at <code>30h</code>/<code>B0h</code> (active bits 0-2, recovery bits 4-7)<br />'''Examined:''' QD6500.SYS 2.4 | | QDI || Vision 6500 || Mid 93 || 1 || PIO-2 || || || Driver || || Yes || Setup configures per drive. Driver picks a timing class from its drive table || '''Detection:''' Register <code>31h</code> (or <code>B1h</code>): upper nibble <code>C0h</code>; bit 3 set = disabled<br />'''Timing registers:''' One timing byte at <code>30h</code>/<code>B0h</code> (active bits 0-2, recovery bits 4-7)<br />'''Examined:''' QD6500.SYS 2.4<br />'''Disk size:''' Follows the BIOS. With an enhanced drive table (signature A0h at INT 41h) and an LBA drive: LBA with the BIOS's geometry, 8.4 GB limit. Otherwise 16 heads, 528 MB limit (QD6500.SYS) | ||
|- | |- | ||
| QDI || Vision 6580 || Late 94 || 2 || PIO-4 || Card || Half || Driver || || Yes || Setup configures per drive || '''Notes:''' PIO timing based on bus clock makes the controller less robust on some systems<br />'''Detection:''' Register <code>31h</code> (or <code>B1h</code>): upper nibble <code>A0h</code> or <code>50h</code><br />'''Timing registers:''' As QD6500, plus secondary-channel timing<br />'''Examined:''' QD6580.sys 3.7 | | QDI || Vision 6580 || Late 94 || 2 || PIO-4 || Card || Half || Driver || || Yes || Setup configures per drive || '''Notes:''' PIO timing based on bus clock makes the controller less robust on some systems<br />'''Detection:''' Register <code>31h</code> (or <code>B1h</code>): upper nibble <code>A0h</code> or <code>50h</code><br />'''Timing registers:''' As QD6500, plus secondary-channel timing<br />'''Examined:''' QD6580.sys 3.7<br />'''Disk size:''' Follows the BIOS. With an enhanced drive table (signature A0h at INT 41h) and an LBA drive: LBA with the BIOS's geometry, 8.4 GB limit. Otherwise 16 heads, 528 MB limit (QD6580.SYS) | ||
|- | |- | ||
| SIS || 83C601 || Early 95 || 1 || PIO-4? || Yes || Yes || Driver || 3.21 || || Waitstate 1 (fast) -7 (slow) || '''Notes:''' 83C601 has newer fab dates than the 83C611.<br />'''Other names:''' Might also work as a PCI controller PCI ID <code>1039:0601</code><br />'''Detection:''' <code>in 1F3h</code>; <code>in 1F2h</code> ×4; out <code>1F2h</code>,F3h; <code>1F2h</code> reads <code>D3h</code><br />'''Timing registers:''' <code>1F2h</code> ← <code>F0h</code> + (wait state − 1) after the same unlock<br />'''Examined:''' S134XM1.SYS 2.0, S134XD1.COM 3.5; SIS611.SYS | | SIS || 83C601 || Early 95 || 1 || PIO-4? || Yes || Yes || Driver || 3.21 || || Waitstate 1 (fast) -7 (slow) || '''Notes:''' 83C601 has newer fab dates than the 83C611.<br />'''Other names:''' Might also work as a PCI controller PCI ID <code>1039:0601</code><br />'''Detection:''' <code>in 1F3h</code>; <code>in 1F2h</code> ×4; out <code>1F2h</code>,F3h; <code>1F2h</code> reads <code>D3h</code><br />'''Timing registers:''' <code>1F2h</code> ← <code>F0h</code> + (wait state − 1) after the same unlock<br />'''Examined:''' S134XM1.SYS 2.0, S134XD1.COM 3.5; SIS611.SYS<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (S134XM1.SYS, SIS611.SYS). S134XD1.COM doesn't hook INT 13h, so with it the BIOS sets the limit | ||
|- | |- | ||
| SIS || 83C611 || Late 93 || 1 || PIO-4? || Yes || || Driver || 3.21 || || Wait state 0-7 for each channel || '''Notes:''' Older than the 83C601<br />'''Other names:''' Driver banner says "VL/PCI-IDE"; the PCI check is unused<br />'''Detection:''' Same <code>1F2h</code> sequence (<code>0C14h</code>)<br />'''Timing registers:''' <code>1F2h</code>: <code>F3h</code>, <code>B5h</code>, then computed wait states<br />'''Examined:''' SIS611.SYS 2.11 | | SIS || 83C611 || Late 93 || 1 || PIO-4? || Yes || || Driver || 3.21 || || Wait state 0-7 for each channel || '''Notes:''' Older than the 83C601<br />'''Other names:''' Driver banner says "VL/PCI-IDE"; the PCI check is unused<br />'''Detection:''' Same <code>1F2h</code> sequence (<code>0C14h</code>)<br />'''Timing registers:''' <code>1F2h</code>: <code>F3h</code>, <code>B5h</code>, then computed wait states<br />'''Examined:''' SIS611.SYS 2.11<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (SIS611.SYS) | ||
|- | |- | ||
| UMC || UM8672F || Late 94 || 1 || PIO-2 || || || Driver || || || Speeds 0 (slow) -11 (fast) || '''Notes:''' PIO-4 with Modded Driver. Driver calls speed 10 the "proper speed" for Enhanced IDE drives<br />'''Other names:''' UM82C872F<br />'''Detection:''' None: <code>108h</code>/<code>109h</code> unlocked with <code>5Ah</code>, no ID read back<br />'''Timing registers:''' Registers <code>D0h</code>-<code>DDh</code> through index <code>108h</code>/data <code>109h</code>; all set to <code>CBh</code> (slowest) first. Six 12-entry tables in UM8672.SYS (chip ID <code>A0h</code>/<code>A2h</code> × 3 bus-speed classes).<br />'''Examined:''' UM8672.SYS 2.1 | | UMC || UM8672F || Late 94 || 1 || PIO-2 || || || Driver || || || Speeds 0 (slow) -11 (fast) || '''Notes:''' PIO-4 with Modded Driver. Driver calls speed 10 the "proper speed" for Enhanced IDE drives<br />'''Other names:''' UM82C872F<br />'''Detection:''' None: <code>108h</code>/<code>109h</code> unlocked with <code>5Ah</code>, no ID read back<br />'''Timing registers:''' Registers <code>D0h</code>-<code>DDh</code> through index <code>108h</code>/data <code>109h</code>; all set to <code>CBh</code> (slowest) first. Six 12-entry tables in UM8672.SYS (chip ID <code>A0h</code>/<code>A2h</code> × 3 bus-speed classes).<br />'''Examined:''' UM8672.SYS 2.1<br />'''Disk size:''' 8.4 GB limit with its optional LBA path (8-bit head count). Its plain CHS path is 16 heads, 528 MB. What turns LBA on isn't traced (UM8672.SYS) | ||
|- | |- | ||
| VIA || VT83C461 || Mid 94 || 2 || PIO-2 || Yes || || Driver || || || <code>PIO_TIME=</code>, <code>DMA_TIME=</code>, <code>SET_DMAM=</code> || '''Notes:''' Has a BIOS / AV140 / AV150 / AV300<br />'''Other names:''' Driver also covers the VT82C496G<br />'''Detection:''' Index <code>A8h</code>/data <code>A9h</code>: register <code>00h</code> upper nibble <code>70h</code>/<code>90h</code>, register <code>71h</code> bit 0 set<br />'''Timing registers:''' Registers <code>71h</code> (IDE enable), <code>93h</code> (timing/mode)<br />'''Examined:''' VIAIDE.SYS 4.02 | | VIA || VT83C461 || Mid 94 || 2 || PIO-2 || Yes || || Driver || || || <code>PIO_TIME=</code>, <code>DMA_TIME=</code>, <code>SET_DMAM=</code> || '''Notes:''' Has a BIOS / AV140 / AV150 / AV300<br />'''Other names:''' Driver also covers the VT82C496G<br />'''Detection:''' Index <code>A8h</code>/data <code>A9h</code>: register <code>00h</code> upper nibble <code>70h</code>/<code>90h</code>, register <code>71h</code> bit 0 set<br />'''Timing registers:''' Registers <code>71h</code> (IDE enable), <code>93h</code> (timing/mode)<br />'''Examined:''' VIAIDE.SYS 4.02<br />'''Disk size:''' Probably 528 MB limit: 16 heads. Sends LBA commands, but its I/O routine takes a 4-bit head and a 10-bit cylinder (VIAIDE.SYS, not fully traced) | ||
|- | |- | ||
| Winbond || W83759AF || Early 95 || 2 || PIO-3 || Yes || Yes || Driver || || || /D0:13 (speeds 0-13) || '''Notes:''' software speed config and "advanced mode". Measures the bus clock with the PC timer. Might support PIO 4; "A" version is software configurable<br />'''Other names:''' DTC 2278E Rev W.<br />'''Detection:''' Bases <code>4B0h</code>/<code>5B0h</code>… then <code>430h</code>/<code>530h</code>…: <code>63h</code> written at base+0 reads back at base+0Ch; register <code>87h</code> low nibble = revision; register <code>80h</code> bit 7 set<br />'''Timing registers:''' Index base+4, data base+8<br />'''Examined:''' WBIDE.EXE, DOSEIDE.SYS 2.1A (at <code>5B0h</code> only) | | Winbond || W83759AF || Early 95 || 2 || PIO-3 || Yes || Yes || Driver || || || /D0:13 (speeds 0-13) || '''Notes:''' software speed config and "advanced mode". Measures the bus clock with the PC timer. Might support PIO 4; "A" version is software configurable<br />'''Other names:''' DTC 2278E Rev W.<br />'''Detection:''' Bases <code>4B0h</code>/<code>5B0h</code>… then <code>430h</code>/<code>530h</code>…: <code>63h</code> written at base+0 reads back at base+0Ch; register <code>87h</code> low nibble = revision; register <code>80h</code> bit 7 set<br />'''Timing registers:''' Index base+4, data base+8<br />'''Examined:''' WBIDE.EXE, DOSEIDE.SYS 2.1A (at <code>5B0h</code> only)<br />'''Disk size:''' 8.4 GB limit: LBA and "Large" (eCHS) modes, from the strings; not traced (WBIDE.EXE, DOSEIDE.SYS) | ||
|- | |- | ||
| Micronics || MIC491 || Mid 93 || 1 || PIO-2? || || || BIOS Setup || || || IDE Speeds: Normal / Medium / Fast<br />(register <code>104h</code> = <code>69h</code> / <code>67h</code> / <code>63h</code>) || '''Notes:''' No driver; but a Gateway BIOS seems to set the controller speed<br />'''Other names:''' Onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS"<br />'''Detection:''' None. The BIOS only checks that no other IDE controller answers at <code>1F0h</code><br />'''Timing registers:''' <code>out 9Ch,7Fh</code> opens ports <code>102h</code>-<code>106h</code>; <code>104h</code> = speed, <code>102h</code> bit 0 = IDE on<br />'''Examined:''' GJX30G BIOS 09-24-93 | | Micronics || MIC491 || Mid 93 || 1 || PIO-2? || || || BIOS Setup || || || IDE Speeds: Normal / Medium / Fast<br />(register <code>104h</code> = <code>69h</code> / <code>67h</code> / <code>63h</code>) || '''Notes:''' No driver; but a Gateway BIOS seems to set the controller speed<br />'''Other names:''' Onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS"<br />'''Detection:''' None. The BIOS only checks that no other IDE controller answers at <code>1F0h</code><br />'''Timing registers:''' <code>out 9Ch,7Fh</code> opens ports <code>102h</code>-<code>106h</code>; <code>104h</code> = speed, <code>102h</code> bit 0 = IDE on<br />'''Examined:''' GJX30G BIOS 09-24-93<br />'''Disk size:''' Set by the system BIOS: the GJX30G code only sets the IDE speed | ||
|} | |} | ||
| Line 44: | Line 44: | ||
| Chaintech || CT9000 || Late 93 || 1 || PIO-3 || Yes || Jumper || 0-3 || '''Notes:''' Not found yet: ct9000.zip | | Chaintech || CT9000 || Late 93 || 1 || PIO-3 || Yes || Jumper || 0-3 || '''Notes:''' Not found yet: ct9000.zip | ||
|- | |- | ||
| DTC || DTC 805 || Early 94 || 1 || PIO-2 || || Jumper || 3.9MB/s - 7.2MB/s || '''Notes:''' DOSEIDE.SYS has no code for it; it only shows the drive's reported rate<br />'''Other names:''' DTC 2278VL, jumpers W1-W5<br />'''Examined:''' DOSEIDE.SYS 2.1A | | DTC || DTC 805 || Early 94 || 1 || PIO-2 || || Jumper || 3.9MB/s - 7.2MB/s || '''Notes:''' DOSEIDE.SYS has no code for it; it only shows the drive's reported rate<br />'''Other names:''' DTC 2278VL, jumpers W1-W5<br />'''Examined:''' DOSEIDE.SYS 2.1A<br />'''Disk size:''' 8.4 GB limit: LBA or EDPT per drive, from its banner strings; not traced (DOSEIDE.SYS) | ||
|- | |- | ||
| GoldStar || GM82C711 || Early 93 || 1 || PIO-3 || || Jumper || 0-7 || '''Notes:''' GS_DOS.SYS driver does not set timing; Not a PC Chips 82C711<br />'''Examined:''' GS_DOS.SYS 1.21 (driver doesn't name the chip) | | GoldStar || GM82C711 || Early 93 || 1 || PIO-3 || || Jumper || 0-7 || '''Notes:''' GS_DOS.SYS driver does not set timing; Not a PC Chips 82C711<br />'''Examined:''' GS_DOS.SYS 1.21 (driver doesn't name the chip)<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (GS_DOS.SYS) | ||
|- | |- | ||
| GoldStar || GM82C712 || Mid 95 || 1 || PIO-4 || Yes || Jumper || 0-7 || '''Notes:''' Same driver as GM82C711<br />'''Other names:''' CompassLab CL3202.<br />'''Examined:''' GS_DOS.SYS 1.21 | | GoldStar || GM82C712 || Mid 95 || 1 || PIO-4 || Yes || Jumper || 0-7 || '''Notes:''' Same driver as GM82C711<br />'''Other names:''' CompassLab CL3202.<br />'''Examined:''' GS_DOS.SYS 1.21<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (GS_DOS.SYS) | ||
|- | |- | ||
| Holtek || HT6560A || Late 94 || 2 || PIO-2 || || Jumper || 0 (slow), 3 (fast) || '''Notes:''' | | Holtek || HT6560A || Late 94 || 2 || PIO-2 || || Jumper + Driver || 0 (slow), 3 (fast). Driver <code>/Dn=rt,at[,m]</code>: recovery 4-15, active 2-15 bus clocks per the readme; the code accepts recovery 4-17 and active 3-15 || '''Notes:''' Same driver code base as the HT6560B's HTIDE 2.41; only the detection, the config bytes and the parameter limits differ<br />'''Detection:''' <code>3E6h</code> handshake: three <code>out 3E6h,0</code> / <code>in 3E6h</code> rounds read non-zero, the fourth reads <code>00h</code><br />'''Timing registers:''' As the HT6560B: four reads of <code>3E6h</code>, config byte to <code>3E6h</code> (<code>05h</code>/<code>04h</code>; <code>07h</code> after detection), then the timing byte (recovery << 4 OR active) to <code>1F6h</code><br />'''Examined:''' HTIDE.SYS 1.80<br />'''Disk size:''' 8.4 GB limit: LBA or bit-shift eCHS, 8-bit logical head count (HTIDE.SYS 1.80) | ||
|- | |- | ||
| Holtek || HT6560B || Early 95 || 2 || PIO-3 || Yes || Jumper + Driver || 0 (slow), 3 (fast). Driver <code>/Dn=rt,at</code>: recovery 2-16, active 2-15 bus clocks || '''Notes:''' Driver allows AT:2 RT:2<br />'''Detection:''' <code>3E6h</code> handshake: after three <code>out 3E6h,0</code> / <code>in 3E6h</code> rounds some of bits 0-5 read back clear; on the fourth all six are set<br />'''Timing registers:''' Four reads of <code>3E6h</code>, then config byte to <code>3E6h</code> and timing byte (recovery << 4 OR active) to <code>1F6h</code>. Linux pata_legacy 5.15 agrees<br />'''Examined:''' HTIDE.SYS 2.41 | | Holtek || HT6560B || Early 95 || 2 || PIO-3 || Yes || Jumper + Driver || 0 (slow), 3 (fast). Driver <code>/Dn=rt,at</code>: recovery 2-16, active 2-15 bus clocks || '''Notes:''' Driver allows AT:2 RT:2<br />'''Detection:''' <code>3E6h</code> handshake: after three <code>out 3E6h,0</code> / <code>in 3E6h</code> rounds some of bits 0-5 read back clear; on the fourth all six are set<br />'''Timing registers:''' Four reads of <code>3E6h</code>, then config byte to <code>3E6h</code> and timing byte (recovery << 4 OR active) to <code>1F6h</code>. Linux pata_legacy 5.15 agrees<br />'''Examined:''' HTIDE.SYS 2.41<br />'''Disk size:''' 8.4 GB limit: LBA or bit-shift eCHS, 8-bit logical head count (HTIDE.SYS) | ||
|- | |- | ||
| Lion || Lion 3+ || Mid 95 || 2 || PIO-3 || || Jumper + Driver || 0 (slow), 2(fast). Driver will lower speed if certain drives are detected || '''Notes:''' Driver doesn't support ECHS or LBA<br />'''Detection:''' Config window on <code>1F0h</code>/<code>1F1h</code> (opened by reads of <code>1F3h</code>, <code>1F2h</code>, <code>3F6h</code>); register 5 & <code>E0h</code> = <code>60h</code><br />'''Timing registers:''' Per-drive registers through the <code>1F0h</code>/<code>1F1h</code> window<br />'''Examined:''' LION3.SYS | | Lion || Lion 3+ || Mid 95 || 2 || PIO-3 || || Jumper + Driver || 0 (slow), 2(fast). Driver will lower speed if certain drives are detected || '''Notes:''' Driver doesn't support ECHS or LBA<br />'''Detection:''' Config window on <code>1F0h</code>/<code>1F1h</code> (opened by reads of <code>1F3h</code>, <code>1F2h</code>, <code>3F6h</code>); register 5 & <code>E0h</code> = <code>60h</code><br />'''Timing registers:''' Per-drive registers through the <code>1F0h</code>/<code>1F1h</code> window<br />'''Examined:''' LION3.SYS<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (LION3.SYS) | ||
|- | |- | ||
| OPTI || 82C611 || Early 93 || 2 || PIO-3 || || Jumper || || '''Notes:''' Probably programmed the same way as the 82C611A; to be tested | | OPTI || 82C611 || Early 93 || 2 || PIO-3 || || Jumper || || '''Notes:''' Probably programmed the same way as the 82C611A; to be tested | ||
|- | |- | ||
| OPTI || 82C611A || Late 94 || 2 || PIO-3 || Card || Jumper + Driver || 0 (slow), 3 (fast). SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz || '''Detection:''' <code>1F3h</code> echoes <code>C0h</code>; then <code>in 1F1h</code> ×2, <code>out 1F2h,03h</code> (config mode), <code>1F3h</code> changes, <code>out 1F2h,83h</code><br />'''Timing registers:''' In config mode: <code>1F3h</code> selects the drive bank, <code>1F1h</code> = write timing, <code>1F6h</code> = setup and read bank, <code>1F0h</code> = read timing, <code>1F5h</code> bits 0-1 = bus-clock strap. Linux pata_legacy 5.15 uses the same sequence for the 82C611A<br />'''Examined:''' optivic.sys 1.0, opti-pio.exe, opti-set.exe | | OPTI || 82C611A || Late 94 || 2 || PIO-3 || Card || Jumper + Driver || 0 (slow), 3 (fast). SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz || '''Detection:''' <code>1F3h</code> echoes <code>C0h</code>; then <code>in 1F1h</code> ×2, <code>out 1F2h,03h</code> (config mode), <code>1F3h</code> changes, <code>out 1F2h,83h</code><br />'''Timing registers:''' In config mode: <code>1F3h</code> selects the drive bank, <code>1F1h</code> = write timing, <code>1F6h</code> = setup and read bank, <code>1F0h</code> = read timing, <code>1F5h</code> bits 0-1 = bus-clock strap. Linux pata_legacy 5.15 uses the same sequence for the 82C611A<br />'''Examined:''' optivic.sys 1.0, opti-pio.exe, opti-set.exe<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (optivic.sys). opti-pio.exe doesn't hook INT 13h, so with it the BIOS sets the limit | ||
|- | |- | ||
| PiC || 1288A-125 || Late 93 || 1 || PIO-2 || Yes || Jumper || 0 (slow), 3 (fast) || '''Notes:''' No driver found<br />'''Other names:''' VIDE-1 | | PiC || 1288A-125 || Late 93 || 1 || PIO-2 || Yes || Jumper || 0 (slow), 3 (fast) || '''Notes:''' No driver found<br />'''Other names:''' VIDE-1 | ||
|- | |- | ||
| Promise || PDC-20230b || Mid 93 || 1 || PIO-3 || || Jumper || 0 (slow), 2(fast) || '''Notes:''' Works with the PROMISE.SYS 3.3 drivers.<br />'''Other names:''' CompassLab CL3201 (fab 9314); TurboChip B<br />'''Detection:''' Write <code>55h</code> to <code>1F2h</code>, read it three times back to back: a 20230-B returns <code>00h</code> on the third read (Soucek; also unreached code in PROMISE.SYS at <code>2D3Bh</code>). Needs the same three reads as a "VLB sync" before 32-bit I/O<br />'''Examined:''' PROMISE.SYS 3.3 | | Promise || PDC-20230b || Mid 93 || 1 || PIO-3 || || Jumper || 0 (slow), 2(fast) || '''Notes:''' Works with the PROMISE.SYS 3.3 drivers.<br />'''Other names:''' CompassLab CL3201 (fab 9314); TurboChip B<br />'''Detection:''' Write <code>55h</code> to <code>1F2h</code>, read it three times back to back: a 20230-B returns <code>00h</code> on the third read (Soucek; also unreached code in PROMISE.SYS at <code>2D3Bh</code>). Needs the same three reads as a "VLB sync" before 32-bit I/O<br />'''Examined:''' PROMISE.SYS 3.3<br />'''Disk size:''' 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) | ||
|- | |- | ||
| UMC || UM82C871F || Mid 93 || 1 || PIO-3 || || Jumper || Best speed: AT:3 RT:4 || '''Notes:''' Driver only uses standard IDE commands; its F5 setup toggles multi-sector mode<br />'''Examined:''' UM82C871F.SYS | | UMC || UM82C871F || Mid 93 || 1 || PIO-3 || || Jumper || Best speed: AT:3 RT:4 || '''Notes:''' Driver only uses standard IDE commands; its F5 setup toggles multi-sector mode<br />'''Examined:''' UM82C871F.SYS<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (UM82C871F.SYS) | ||
|- | |- | ||
| UMC || UM85C418F || Late 93 || 1 || PIO-2 || || Jumper || Best speed: AT:5 RT:9 || '''Notes:''' Combo IDE & VGA controller; The driver writes register <code>D1h</code> when certain drives are detected. Stability issues at fastest speeds<br />'''Detection:''' None: <code>108h</code>/<code>109h</code> unlocked with <code>5Ah</code>, no ID read back<br />'''Timing registers:''' Register <code>D1h</code> through index <code>108h</code>/data <code>109h</code> (one value for both drives)<br />'''Examined:''' UM85C418F.SYS 1.07 | | UMC || UM85C418F || Late 93 || 1 || PIO-2 || || Jumper || Best speed: AT:5 RT:9 || '''Notes:''' Combo IDE & VGA controller; The driver writes register <code>D1h</code> when certain drives are detected. Stability issues at fastest speeds<br />'''Detection:''' None: <code>108h</code>/<code>109h</code> unlocked with <code>5Ah</code>, no ID read back<br />'''Timing registers:''' Register <code>D1h</code> through index <code>108h</code>/data <code>109h</code> (one value for both drives)<br />'''Examined:''' UM85C418F.SYS 1.07<br />'''Disk size:''' 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (UM85C418F.SYS) | ||
|- | |- | ||
| Winbond || W83759F || Early 94 || 2 || PIO-2 || || Jumper || 600ns, 500ns, 400ns, 240ns || '''Notes:''' winbond_port (Linux pata_legacy parameter; default base <code>130h</code>, alternate <code>1B0h</code>)<br />'''Detection:''' Same probe as the W83759AF? WBIDE reads a revision letter; DOSEIDE needs revision B or later. Linux only programs the W83759A, after turning off jumper mode (register <code>81h</code> bit 7). | | Winbond || W83759F || Early 94 || 2 || PIO-2 || || Jumper || 600ns, 500ns, 400ns, 240ns || '''Notes:''' winbond_port (Linux pata_legacy parameter; default base <code>130h</code>, alternate <code>1B0h</code>)<br />'''Detection:''' Same probe as the W83759AF? WBIDE reads a revision letter; DOSEIDE needs revision B or later. Linux only programs the W83759A, after turning off jumper mode (register <code>81h</code> bit 7). | ||
Revision as of 01:25, 13 November 2026
Full VL-bus IDE chip list
Software-configured
| Brand | Chip | Earliest FAB Date | IDE Ports | Fastest Mode | IO RDY | Internal Strobes | Config Method | MR BIOS Support | XUB Support | Commandline Parameters | Notes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| ADD2 | DW729 | Late 93 | 2 | PIO-3 | Driver | Example Parameters: D0:S/20 R/68 W/FF M/FF P/11 Dx --> x is the drive number starting a 0 S/xx --> hex sectors per transfer for the drive <=32 R/ar --> Read cycles. a = active - 1; r = recovery - 1. Example: R/68 = 9 active cycles, 7 recovery cycles W/ar --> Write cycles, same format as Read M/ar --> Other I/O cycles, same format as Read P/xx --> Bit 0: Enable read-ahead, Bit 1: Enable Post Write, Bit 2: Disable read waits, Bit 3: Disable write waits, Bit 4: Enable 32-bit transfers, Bits 5-7: Undefined. Example: P/11 means Enable read ahead and 32 bit writes /X --> Skip speed test |
Notes: Driver code is XOR-encrypted Other names: Dataworld DW729 Detection: Bases 100h-1C0h: out base,85h unlock, register 0Ah reads 41h ('A'). Genuine part: register 17h = B5hTiming registers: Registers 80h-87h at base+1 after each 85h unlockExamined: ADD_IDE.SYS 1.03 Disk size: 8.4 GB limit: eCHS. Bit-shift translation of the BIOS geometry, CHS to the drive, no LBA. Drives 80h/81h only (ADD_IDE.SYS) | ||||
| Appian | ADI/2 | Mid 93 | 1 | PIO-4 | Yes | Yes | Driver | 3.21 | verbose --> Prints debug output while loading floppy --> Changes chip register 0Fh (handling of port 3F7h) so the chip works alongside a floppy controller initonly --> Programs the chip but leaves the disks on the BIOS; also turns multiple mode off noinit --> Skips the chip set-up routine; the driver still loads io16 / io32 --> Forces 16-bit or 32-bit data transfers instead of auto-detecting b=n --> Bus clock period in ns: b=30 = 33 MHz, b=25 = 40 MHz, b=20 = 50 MHz c=m --> Enable multiple-sector (block) transfers for C: c=s --> Disable multiple-sector (block) transfers for C: ctime=320,320 --> set PIO 0 for Drive C: ctime=300,270 --> set PIO 1 for Drive C: ctime=210,150 --> set PIO 2 for Drive C: ctime=80,100 --> set PIO 3 for Drive C: ctime=70,50 --> set PIO 4 for Drive C: |
Notes: flexidrv.sys from Adaptec seems like the best driver. FLEXIDRV rejects the DMA options (,a) on this chip, and using one drops both drives to mode 0Other names: ALi M5213; CL-PD7220; AIC-25VL01 Detection: Ports 35h/B5h must differ from the PIC masks at 21h/A1h. Then an ID echo at 0AD4h, 34h or B4h: ID below 38h = AIC-25VL01 (38h+ is the AIC-25PC10)Timing registers: ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7-4, recovery clocks in bits 3-0. 7/12: address setup. 1: config; 13: revision Examined: FLEXIDRV.SYS 2.14 Disk size: 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS, no LBA (FLEXIDRV.SYS) | |
| Adaptec | AIC-25PC10 | Not seen yet | Not seen yet | MWDMA-2 | Yes | Yes | Driver | 3.21 | All of the ADI/2 options, plus: c=m,a --> Multiword DMA for C: c=s,a --> Single-word DMA for C: c=a --> DMA for C:, multiword if the drive supports it, otherwise single-word ctime=60,40 --> PIO 5 timing for C:; only faster than PIO 4 at 40 or 50 MHz |
Notes: The AIC-25PC10 seems to have additional functionality. Its DMA is on the IDE cable only: the driver sends READ/WRITE DMA, but the CPU still moves the data through the data port Detection: VL-bus mode: same probe as the ADI/2, with an ID echo of 38h or higher at 0AD4h, 34h or B4h. PCI mode: Appian 1097:0038Timing registers: As the ADI/2, but the data port is a word wide. DMA timing in registers 23h/24h (drive 0) and 28h/29h (drive 1); bit 4 of 7/12 set for DMAExamined: FLEXIDRV.SYS 2.14 Disk size: 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS, no LBA (FLEXIDRV.SYS) | |
| Atronics | IDE-2015PL | Late 94 | 2 | PIO-4 | Driver | /Dx:Px where x= 0-4. /T:25/33/40/50 picks the bus-clock table |
Notes: 2015PL.SYS /Dx:P4 Other names: DTC 803 Detection: Index E0h/data E4h, then B0h/B4h; register echo with 3F6h reads between accessesTiming registers: One register per drive through the same index/data pair. 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25-50 MHz; /T:66 reads past the tables (bug). Linux dtc2278.c writes A0h/C3h for PIO 3+ at B0h/B4hExamined: 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A Disk size: 8.4 GB limit: LBA for drives over 528 MB, but still addressed through CHS INT 13h calls (2015PL.SYS) | ||||
| CMD | PCI0640B | Late 94 | 2 | MWDMA-1 | Yes | Yes | Driver | 3.21 | /PIOMODE:X where x= 0-4. CMD640X.VL 2.09 uses /A<MHz>, /O<port><drive><mode>, /H |
Notes: Advanced features cause data corruption in multitasking environments. Hidden switches: /CMD, /FOO:BARDetection: Index 178h/data 17Ch (else 78h/7Ch): register 50h not 00h/FFh, bit 5 set; register 5Bh echoes BDhTiming registers: Registers 51h-58h; per-drive clocks computed from /A<MHz>Examined: CMD640X.VL 2.09 Disk size: eCHS by default (bit-shift translation), LBA with /L, 528 MB with /T. Probably about 4.2 GB in practice: each halving of the cylinders doubles a byte-sized head count, which overflows after 128 heads (CMD640X.VL) | |
| Promise | PDC-20230c | Late 93 | 1 | PIO-3 | Yes | Yes | Driver | 3.21 | Yes | 0(slow), 8 (fast), A (iordy). The PROMISE.SYS 3.3 README lists levels 0-8. Config-mode 1F3h speeds 0-7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. Levels 0-8 confirmed ; PROMISE.SYS has 9-entry tables, one per level |
Other names: VG3, TurboChip C Detection: Config-mode unlock on the IDE ports: in 1F5h, set 1F2h bit 7, in 1F2h, in 3F6h ×2, in 1F2h ×3; bit 7 reads back clear = PromiseTiming registers: Index 1F8h/data 1F9h: registers 2n/2n+1 get a word from one of four tables chosen by the measured bus speed. Register 7 = transfer status. No chip ID read; same code for every Promise chip. Four 9-entry tables (one per measured bus class), shared by all three Promise chipsExamined: PROMISE.SYS 3.3 Disk size: 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) |
| Promise | PDC-20630 | Mid 94 | 2 | WDMA2 | Yes | Yes | Driver | 3.21 | Yes | 0(slow), 8 (fast), A (iordy), M (mwdma) | Notes: READ/WRITE DMA (C8h/CAh) enables MWDMA to the chip, but data still moves to memory by PIO from 1F0h. Driver only seems to set MWDMA-1 (SET FEATURES 21h, DMA levels 7-8); it never sends 22hOther names: VG4 Detection: As PDC-20230c, then 1F4h bit 3 makes 1F8h read back its index (bits 0-2)Timing registers: 1F3h speed as PDC-20230c, plus four timing registers through 1F8h/1F9h (enabled by 1F4h bit 3)Examined: PROMISE.SYS 3.3 (same code path; no chip check) Disk size: 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) |
| QDI | Vision 6500 | Mid 93 | 1 | PIO-2 | Driver | Yes | Setup configures per drive. Driver picks a timing class from its drive table | Detection: Register 31h (or B1h): upper nibble C0h; bit 3 set = disabledTiming registers: One timing byte at 30h/B0h (active bits 0-2, recovery bits 4-7)Examined: QD6500.SYS 2.4 Disk size: Follows the BIOS. With an enhanced drive table (signature A0h at INT 41h) and an LBA drive: LBA with the BIOS's geometry, 8.4 GB limit. Otherwise 16 heads, 528 MB limit (QD6500.SYS) | |||
| QDI | Vision 6580 | Late 94 | 2 | PIO-4 | Card | Half | Driver | Yes | Setup configures per drive | Notes: PIO timing based on bus clock makes the controller less robust on some systems Detection: Register 31h (or B1h): upper nibble A0h or 50hTiming registers: As QD6500, plus secondary-channel timing Examined: QD6580.sys 3.7 Disk size: Follows the BIOS. With an enhanced drive table (signature A0h at INT 41h) and an LBA drive: LBA with the BIOS's geometry, 8.4 GB limit. Otherwise 16 heads, 528 MB limit (QD6580.SYS) | |
| SIS | 83C601 | Early 95 | 1 | PIO-4? | Yes | Yes | Driver | 3.21 | Waitstate 1 (fast) -7 (slow) | Notes: 83C601 has newer fab dates than the 83C611. Other names: Might also work as a PCI controller PCI ID 1039:0601Detection: in 1F3h; in 1F2h ×4; out 1F2h,F3h; 1F2h reads D3hTiming registers: 1F2h ← F0h + (wait state − 1) after the same unlockExamined: S134XM1.SYS 2.0, S134XD1.COM 3.5; SIS611.SYS Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (S134XM1.SYS, SIS611.SYS). S134XD1.COM doesn't hook INT 13h, so with it the BIOS sets the limit | |
| SIS | 83C611 | Late 93 | 1 | PIO-4? | Yes | Driver | 3.21 | Wait state 0-7 for each channel | Notes: Older than the 83C601 Other names: Driver banner says "VL/PCI-IDE"; the PCI check is unused Detection: Same 1F2h sequence (0C14h)Timing registers: 1F2h: F3h, B5h, then computed wait statesExamined: SIS611.SYS 2.11 Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (SIS611.SYS) | ||
| UMC | UM8672F | Late 94 | 1 | PIO-2 | Driver | Speeds 0 (slow) -11 (fast) | Notes: PIO-4 with Modded Driver. Driver calls speed 10 the "proper speed" for Enhanced IDE drives Other names: UM82C872F Detection: None: 108h/109h unlocked with 5Ah, no ID read backTiming registers: Registers D0h-DDh through index 108h/data 109h; all set to CBh (slowest) first. Six 12-entry tables in UM8672.SYS (chip ID A0h/A2h × 3 bus-speed classes).Examined: UM8672.SYS 2.1 Disk size: 8.4 GB limit with its optional LBA path (8-bit head count). Its plain CHS path is 16 heads, 528 MB. What turns LBA on isn't traced (UM8672.SYS) | ||||
| VIA | VT83C461 | Mid 94 | 2 | PIO-2 | Yes | Driver | PIO_TIME=, DMA_TIME=, SET_DMAM= |
Notes: Has a BIOS / AV140 / AV150 / AV300 Other names: Driver also covers the VT82C496G Detection: Index A8h/data A9h: register 00h upper nibble 70h/90h, register 71h bit 0 setTiming registers: Registers 71h (IDE enable), 93h (timing/mode)Examined: VIAIDE.SYS 4.02 Disk size: Probably 528 MB limit: 16 heads. Sends LBA commands, but its I/O routine takes a 4-bit head and a 10-bit cylinder (VIAIDE.SYS, not fully traced) | |||
| Winbond | W83759AF | Early 95 | 2 | PIO-3 | Yes | Yes | Driver | /D0:13 (speeds 0-13) | Notes: software speed config and "advanced mode". Measures the bus clock with the PC timer. Might support PIO 4; "A" version is software configurable Other names: DTC 2278E Rev W. Detection: Bases 4B0h/5B0h… then 430h/530h…: 63h written at base+0 reads back at base+0Ch; register 87h low nibble = revision; register 80h bit 7 setTiming registers: Index base+4, data base+8 Examined: WBIDE.EXE, DOSEIDE.SYS 2.1A (at 5B0h only)Disk size: 8.4 GB limit: LBA and "Large" (eCHS) modes, from the strings; not traced (WBIDE.EXE, DOSEIDE.SYS) | ||
| Micronics | MIC491 | Mid 93 | 1 | PIO-2? | BIOS Setup | IDE Speeds: Normal / Medium / Fast (register 104h = 69h / 67h / 63h) |
Notes: No driver; but a Gateway BIOS seems to set the controller speed Other names: Onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS" Detection: None. The BIOS only checks that no other IDE controller answers at 1F0hTiming registers: out 9Ch,7Fh opens ports 102h-106h; 104h = speed, 102h bit 0 = IDE onExamined: GJX30G BIOS 09-24-93 Disk size: Set by the system BIOS: the GJX30G code only sets the IDE speed |
Jumper-configured
| Brand | Chip | Earliest FAB Date | IDE Ports | Fastest Mode | IO RDY | Config Method | Speed Settings | Notes |
|---|---|---|---|---|---|---|---|---|
| Chaintech | CT9000 | Late 93 | 1 | PIO-3 | Yes | Jumper | 0-3 | Notes: Not found yet: ct9000.zip |
| DTC | DTC 805 | Early 94 | 1 | PIO-2 | Jumper | 3.9MB/s - 7.2MB/s | Notes: DOSEIDE.SYS has no code for it; it only shows the drive's reported rate Other names: DTC 2278VL, jumpers W1-W5 Examined: DOSEIDE.SYS 2.1A Disk size: 8.4 GB limit: LBA or EDPT per drive, from its banner strings; not traced (DOSEIDE.SYS) | |
| GoldStar | GM82C711 | Early 93 | 1 | PIO-3 | Jumper | 0-7 | Notes: GS_DOS.SYS driver does not set timing; Not a PC Chips 82C711 Examined: GS_DOS.SYS 1.21 (driver doesn't name the chip) Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (GS_DOS.SYS) | |
| GoldStar | GM82C712 | Mid 95 | 1 | PIO-4 | Yes | Jumper | 0-7 | Notes: Same driver as GM82C711 Other names: CompassLab CL3202. Examined: GS_DOS.SYS 1.21 Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (GS_DOS.SYS) |
| Holtek | HT6560A | Late 94 | 2 | PIO-2 | Jumper + Driver | 0 (slow), 3 (fast). Driver /Dn=rt,at[,m]: recovery 4-15, active 2-15 bus clocks per the readme; the code accepts recovery 4-17 and active 3-15 |
Notes: Same driver code base as the HT6560B's HTIDE 2.41; only the detection, the config bytes and the parameter limits differ Detection: 3E6h handshake: three out 3E6h,0 / in 3E6h rounds read non-zero, the fourth reads 00hTiming registers: As the HT6560B: four reads of 3E6h, config byte to 3E6h (05h/04h; 07h after detection), then the timing byte (recovery << 4 OR active) to 1F6hExamined: HTIDE.SYS 1.80 Disk size: 8.4 GB limit: LBA or bit-shift eCHS, 8-bit logical head count (HTIDE.SYS 1.80) | |
| Holtek | HT6560B | Early 95 | 2 | PIO-3 | Yes | Jumper + Driver | 0 (slow), 3 (fast). Driver /Dn=rt,at: recovery 2-16, active 2-15 bus clocks |
Notes: Driver allows AT:2 RT:2 Detection: 3E6h handshake: after three out 3E6h,0 / in 3E6h rounds some of bits 0-5 read back clear; on the fourth all six are setTiming registers: Four reads of 3E6h, then config byte to 3E6h and timing byte (recovery << 4 OR active) to 1F6h. Linux pata_legacy 5.15 agreesExamined: HTIDE.SYS 2.41 Disk size: 8.4 GB limit: LBA or bit-shift eCHS, 8-bit logical head count (HTIDE.SYS) |
| Lion | Lion 3+ | Mid 95 | 2 | PIO-3 | Jumper + Driver | 0 (slow), 2(fast). Driver will lower speed if certain drives are detected | Notes: Driver doesn't support ECHS or LBA Detection: Config window on 1F0h/1F1h (opened by reads of 1F3h, 1F2h, 3F6h); register 5 & E0h = 60hTiming registers: Per-drive registers through the 1F0h/1F1h windowExamined: LION3.SYS Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (LION3.SYS) | |
| OPTI | 82C611 | Early 93 | 2 | PIO-3 | Jumper | Notes: Probably programmed the same way as the 82C611A; to be tested | ||
| OPTI | 82C611A | Late 94 | 2 | PIO-3 | Card | Jumper + Driver | 0 (slow), 3 (fast). SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz | Detection: 1F3h echoes C0h; then in 1F1h ×2, out 1F2h,03h (config mode), 1F3h changes, out 1F2h,83hTiming registers: In config mode: 1F3h selects the drive bank, 1F1h = write timing, 1F6h = setup and read bank, 1F0h = read timing, 1F5h bits 0-1 = bus-clock strap. Linux pata_legacy 5.15 uses the same sequence for the 82C611AExamined: optivic.sys 1.0, opti-pio.exe, opti-set.exe Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (optivic.sys). opti-pio.exe doesn't hook INT 13h, so with it the BIOS sets the limit |
| PiC | 1288A-125 | Late 93 | 1 | PIO-2 | Yes | Jumper | 0 (slow), 3 (fast) | Notes: No driver found Other names: VIDE-1 |
| Promise | PDC-20230b | Mid 93 | 1 | PIO-3 | Jumper | 0 (slow), 2(fast) | Notes: Works with the PROMISE.SYS 3.3 drivers. Other names: CompassLab CL3201 (fab 9314); TurboChip B Detection: Write 55h to 1F2h, read it three times back to back: a 20230-B returns 00h on the third read (Soucek; also unreached code in PROMISE.SYS at 2D3Bh). Needs the same three reads as a "VLB sync" before 32-bit I/OExamined: PROMISE.SYS 3.3 Disk size: 8.4 GB limit: eCHS. Translates logical CHS to the drive's physical CHS (PROMISE.SYS) | |
| UMC | UM82C871F | Mid 93 | 1 | PIO-3 | Jumper | Best speed: AT:3 RT:4 | Notes: Driver only uses standard IDE commands; its F5 setup toggles multi-sector mode Examined: UM82C871F.SYS Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (UM82C871F.SYS) | |
| UMC | UM85C418F | Late 93 | 1 | PIO-2 | Jumper | Best speed: AT:5 RT:9 | Notes: Combo IDE & VGA controller; The driver writes register D1h when certain drives are detected. Stability issues at fastest speedsDetection: None: 108h/109h unlocked with 5Ah, no ID read backTiming registers: Register D1h through index 108h/data 109h (one value for both drives)Examined: UM85C418F.SYS 1.07 Disk size: 528 MB limit: 16 heads. The BIOS head number goes straight to the drive (UM85C418F.SYS) | |
| Winbond | W83759F | Early 94 | 2 | PIO-2 | Jumper | 600ns, 500ns, 400ns, 240ns | Notes: winbond_port (Linux pata_legacy parameter; default base 130h, alternate 1B0h)Detection: Same probe as the W83759AF? WBIDE reads a revision letter; DOSEIDE needs revision B or later. Linux only programs the W83759A, after turning off jumper mode (register 81h bit 7).
|
No configuration
No driver or setup utility has been found for these chips.
| Brand | Chip | Earliest FAB Date | IDE Ports | Notes |
|---|---|---|---|---|
| QDI | Vision 5500 | N/A | 1 | The existence of this chip was inferred by the existence of a QDI5500 VLB IDE controller in the TH99 repository. No photos found. |
| Tans | TS8310 | Mid 94 | 2 | References to ts8310.zip exist on BBS sites, but no uncorrupted versions exist. TANS BIOS files have been found but are controller agnostic. Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997) SIIG v3.10, which resembles v2.00 with a name change TANS "Enhance IDE driver" v2.10 ">8.4GB" (1999) All use only the standard IDE ports at 1F0h/170h/1E8h/168h: No chip detection, no timing writes, and 16-bit rep insw/outsw only (no 32-bit I/O)
|
| Tans | TS8310A | Late 94 | 2 | Same as above |
| Mach Speed | GTK6189 | Early 94 | 1 | No driver found. Frequently found paired with a Cirrus CL-GD5428 VGA; The 40-pin IDE header has never been seen fitted, some traces run to the VGA chip. The card ROM is a standard Cirrus VGA BIOS with nothing about IDE. Jumper positions are unpopulated except one that is hard-shorted, probably to disable the IDE function. Possibly IDE functionality was dropped late in the design |
| Opus | Op VIC1 | Late 93 | 1 | No driver found. "Op VIC" = Opus Vesa Ide Controller ? |
| Opus | Op VIC3 | Early 94 | 2 | No driver found. "Op VIC" = Opus Vesa Ide Controller ? |