VLB IDE Controllers: Difference between revisions

From Vogons Wiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 8: Line 8:
| ADD2 || DW729 || Late 93 || 2 || PIO-3 ||  ||  || Driver ||  ||  || Setup configures per drive || '''Notes:''' Driver Options: S/00 R/00 W/00 M/00 P/00. Driver code is XOR-encrypted<br />'''Other names:''' Dataworld DW729<br />'''Detection:''' Bases <code>100h</code>-<code>1C0h</code>: <code>out base,85h</code> unlock, register <code>0Ah</code> reads <code>41h</code> ('A'). Genuine part: register <code>17h</code> = <code>B5h</code><br />'''Timing registers:''' Registers <code>80h</code>-<code>87h</code> at base+1 after each <code>85h</code> unlock<br />'''Examined:''' ADD_IDE.SYS 1.03
| ADD2 || DW729 || Late 93 || 2 || PIO-3 ||  ||  || Driver ||  ||  || Setup configures per drive || '''Notes:''' Driver Options: S/00 R/00 W/00 M/00 P/00. Driver code is XOR-encrypted<br />'''Other names:''' Dataworld DW729<br />'''Detection:''' Bases <code>100h</code>-<code>1C0h</code>: <code>out base,85h</code> unlock, register <code>0Ah</code> reads <code>41h</code> ('A'). Genuine part: register <code>17h</code> = <code>B5h</code><br />'''Timing registers:''' Registers <code>80h</code>-<code>87h</code> at base+1 after each <code>85h</code> unlock<br />'''Examined:''' ADD_IDE.SYS 1.03
|-
|-
| Appian || ADI/2 || Mid 93 || 1 || PIO-4 || Yes || Yes || Driver || 3.21 ||  || <code>ctime=</code>, <code>dtime=</code> (also <code>c=</code>, <code>d=</code>, <code>s=</code>, <code>m=</code>) (was: No flags) || '''Notes:''' flexidrv.sys from Adaptec is best<br />'''Other names:''' ALi M5213; AIC-25VL0x; CL-PD7220. FLEXIDRV also drives the AIC-25PC10 (VL-bus or PCI)<br />'''Detection:''' Ports <code>35h</code>/<code>B5h</code> must differ from the PIC masks at <code>21h</code>/<code>A1h</code>. Then an ID echo at <code>0AD4h</code>, <code>34h</code> or <code>B4h</code>: ID <code>38h</code>+ = AIC-25PC10 (VL-bus mode), lower = AIC-25VL01. The PCI 25PC10 is Appian <code>1097:0038</code><br />'''Timing registers:''' ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7-4, recovery clocks in bits 3-0. 7/12: address setup. 1: config; 13: revision<br />'''Examined:''' FLEXIDRV.SYS 2.14
| Appian || ADI/2 || Mid 93 || 1 || PIO-4 || Yes || Yes || Driver || 3.21 ||  || <code>ctime=</code>, <code>dtime=</code> (also <code>c=</code>, <code>d=</code>, <code>s=</code>, <code>m=</code>) || '''Notes:''' flexidrv.sys from Adaptec is best<br />'''Other names:''' ALi M5213; AIC-25VL0x; CL-PD7220. FLEXIDRV also drives the AIC-25PC10 (VL-bus or PCI)<br />'''Detection:''' Ports <code>35h</code>/<code>B5h</code> must differ from the PIC masks at <code>21h</code>/<code>A1h</code>. Then an ID echo at <code>0AD4h</code>, <code>34h</code> or <code>B4h</code>: ID <code>38h</code>+ = AIC-25PC10 (VL-bus mode), lower = AIC-25VL01. The PCI 25PC10 is Appian <code>1097:0038</code><br />'''Timing registers:''' ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7-4, recovery clocks in bits 3-0. 7/12: address setup. 1: config; 13: revision<br />'''Examined:''' FLEXIDRV.SYS 2.14
|-
|-
| Atronics || IDE-2015PL || Late 94 || 2 || PIO-4 ||  ||  || Driver ||  ||  || /Dx:Px where x= 0-4. <code>/T:25/33/40/50</code> picks the bus-clock table || '''Notes:''' 2015PL.SYS /Dx:P4<br />'''Other names:''' DTC 803 (sticker on the 2015PL; VL DTC 2278S/D/D Plus/E/B and PCI 2130D)<br />'''Detection:''' Index <code>E0h</code>/data <code>E4h</code>, then <code>B0h</code>/<code>B4h</code>; register echo with <code>3F6h</code> reads between accesses<br />'''Timing registers:''' One register per drive through the same index/data pair. 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25-50 MHz; <code>/T:66</code> reads past the tables (bug). Linux <code>dtc2278.c</code> writes <code>A0h</code>/<code>C3h</code> for PIO 3+ at <code>B0h</code>/<code>B4h</code><br />'''Examined:''' 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A
| Atronics || IDE-2015PL || Late 94 || 2 || PIO-4 ||  ||  || Driver ||  ||  || /Dx:Px where x= 0-4. <code>/T:25/33/40/50</code> picks the bus-clock table || '''Notes:''' 2015PL.SYS /Dx:P4<br />'''Other names:''' DTC 803 (sticker on the 2015PL; VL DTC 2278S/D/D Plus/E/B and PCI 2130D)<br />'''Detection:''' Index <code>E0h</code>/data <code>E4h</code>, then <code>B0h</code>/<code>B4h</code>; register echo with <code>3F6h</code> reads between accesses<br />'''Timing registers:''' One register per drive through the same index/data pair. 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25-50 MHz; <code>/T:66</code> reads past the tables (bug). Linux <code>dtc2278.c</code> writes <code>A0h</code>/<code>C3h</code> for PIO 3+ at <code>B0h</code>/<code>B4h</code><br />'''Examined:''' 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A
Line 30: Line 30:
| VIA || VT83C461 || Mid 94 || 2 || PIO-2 || Yes ||  || Driver ||  ||  || <code>PIO_TIME=</code>, <code>DMA_TIME=</code>, <code>SET_DMAM=</code> || '''Notes:''' Has a BIOS / AV140 / AV150 / AV300<br />'''Other names:''' Driver also covers the VT82C496G<br />'''Detection:''' Index <code>A8h</code>/data <code>A9h</code>: register <code>00h</code> upper nibble <code>70h</code>/<code>90h</code>, register <code>71h</code> bit 0 set<br />'''Timing registers:''' Registers <code>71h</code> (IDE enable), <code>93h</code> (timing/mode)<br />'''Examined:''' VIAIDE.SYS 4.02
| VIA || VT83C461 || Mid 94 || 2 || PIO-2 || Yes ||  || Driver ||  ||  || <code>PIO_TIME=</code>, <code>DMA_TIME=</code>, <code>SET_DMAM=</code> || '''Notes:''' Has a BIOS / AV140 / AV150 / AV300<br />'''Other names:''' Driver also covers the VT82C496G<br />'''Detection:''' Index <code>A8h</code>/data <code>A9h</code>: register <code>00h</code> upper nibble <code>70h</code>/<code>90h</code>, register <code>71h</code> bit 0 set<br />'''Timing registers:''' Registers <code>71h</code> (IDE enable), <code>93h</code> (timing/mode)<br />'''Examined:''' VIAIDE.SYS 4.02
|-
|-
| Winbond || W83759AF || Early 95 || 2 || PIO-4 (WBIDE.TXT's ns table makes speed 13 = PIO 3 at 33 MHz) || Yes || Yes || Driver ||  ||  || /D0:13 (speeds 0-13) || '''Notes:''' software speed config and "advanced mode". Measures the bus clock with the PC timer. A hacked driver that enables PIO 4 is reported to exist (Douglar)<br />'''Other names:''' DTC 2278E Rev W. F = package type; the A suggests a silicon respin (Douglar)<br />'''Detection:''' Bases <code>4B0h</code>/<code>5B0h</code>… then <code>430h</code>/<code>530h</code>…: <code>63h</code> written at base+0 reads back at base+0Ch; register <code>87h</code> low nibble = revision; register <code>80h</code> bit 7 set<br />'''Timing registers:''' Index base+4, data base+8<br />'''Examined:''' WBIDE.EXE, DOSEIDE.SYS 2.1A (at <code>5B0h</code> only)
| Winbond || W83759AF || Early 95 || 2 || PIO-3 || Yes || Yes || Driver ||  ||  || /D0:13 (speeds 0-13) || '''Notes:''' software speed config and "advanced mode". Measures the bus clock with the PC timer. A hacked driver that enables PIO 4 is reported to exist (Douglar)<br />'''Other names:''' DTC 2278E Rev W. F = package type; the A suggests a silicon respin (Douglar)<br />'''Detection:''' Bases <code>4B0h</code>/<code>5B0h</code>… then <code>430h</code>/<code>530h</code>…: <code>63h</code> written at base+0 reads back at base+0Ch; register <code>87h</code> low nibble = revision; register <code>80h</code> bit 7 set<br />'''Timing registers:''' Index base+4, data base+8<br />'''Examined:''' WBIDE.EXE, DOSEIDE.SYS 2.1A (at <code>5B0h</code> only)
|-
|-
| Micronics || MIC491 || Mid 93 || 1 || unknown ||  ||  || BIOS Setup ||  ||  || IDE Speed: Normal / Medium / Fast (register <code>104h</code> = <code>69h</code> / <code>67h</code> / <code>63h</code>) || '''Notes:''' No driver; the system BIOS sets it<br />'''Other names:''' Onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS"<br />'''Detection:''' None. The BIOS only checks that no other IDE controller answers at <code>1F0h</code><br />'''Timing registers:''' <code>out 9Ch,7Fh</code> opens ports <code>102h</code>-<code>106h</code>; <code>104h</code> = speed, <code>102h</code> bit 0 = IDE on<br />'''Examined:''' GJX30G BIOS 09-24-93
| Micronics || MIC491 || Mid 93 || 1 || unknown ||  ||  || BIOS Setup ||  ||  || IDE Speed: Normal / Medium / Fast (register <code>104h</code> = <code>69h</code> / <code>67h</code> / <code>63h</code>) || '''Notes:''' No driver; the system BIOS sets it<br />'''Other names:''' Onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS"<br />'''Detection:''' None. The BIOS only checks that no other IDE controller answers at <code>1F0h</code><br />'''Timing registers:''' <code>out 9Ch,7Fh</code> opens ports <code>102h</code>-<code>106h</code>; <code>104h</code> = speed, <code>102h</code> bit 0 = IDE on<br />'''Examined:''' GJX30G BIOS 09-24-93
Line 50: Line 50:
| Holtek || HT6560A || Late 94 || 2 || PIO-2 ||  || Jumper || 0 (slow), 3 (fast) || '''Notes:''' Driver Not found yet
| Holtek || HT6560A || Late 94 || 2 || PIO-2 ||  || Jumper || 0 (slow), 3 (fast) || '''Notes:''' Driver Not found yet
|-
|-
| Holtek || HT6560B || Early 95 || 2 || PIO-3 || Yes || Jumper + Driver (was: Jumper) || 0 (slow), 3 (fast). Driver <code>/Dn=rt,at</code>: recovery 2-16, active 2-15 bus clocks || '''Notes:''' Driver allows AT:2 RT:2<br />'''Detection:''' <code>3E6h</code> handshake: after three <code>out 3E6h,0</code> / <code>in 3E6h</code> rounds some of bits 0-5 read back clear; on the fourth all six are set<br />'''Timing registers:''' Four reads of <code>3E6h</code>, then config byte to <code>3E6h</code> and timing byte (recovery &lt;&lt; 4 OR active) to <code>1F6h</code> (was: Timing bytes to <code>3E6h</code>). Linux pata_legacy 5.15 agrees<br />'''Examined:''' HTIDE.SYS 2.41
| Holtek || HT6560B || Early 95 || 2 || PIO-3 || Yes || Jumper + Driver || 0 (slow), 3 (fast). Driver <code>/Dn=rt,at</code>: recovery 2-16, active 2-15 bus clocks || '''Notes:''' Driver allows AT:2 RT:2<br />'''Detection:''' <code>3E6h</code> handshake: after three <code>out 3E6h,0</code> / <code>in 3E6h</code> rounds some of bits 0-5 read back clear; on the fourth all six are set<br />'''Timing registers:''' Four reads of <code>3E6h</code>, then config byte to <code>3E6h</code> and timing byte (recovery &lt;&lt; 4 OR active) to <code>1F6h</code>. Linux pata_legacy 5.15 agrees<br />'''Examined:''' HTIDE.SYS 2.41
|-
|-
| Lion || Lion 3+ || Mid 95 || 2 || PIO-3 ||  || Jumper + Driver (was: Jumper) || 0 (slow), 2(fast). Driver sets a mode per drive || '''Notes:''' Doesn't support ECHS or LBA<br />'''Detection:''' Config window on <code>1F0h</code>/<code>1F1h</code> (opened by reads of <code>1F3h</code>, <code>1F2h</code>, <code>3F6h</code>); register 5 &amp; <code>E0h</code> = <code>60h</code><br />'''Timing registers:''' Per-drive registers through the <code>1F0h</code>/<code>1F1h</code> window<br />'''Examined:''' LION3.SYS
| Lion || Lion 3+ || Mid 95 || 2 || PIO-3 ||  || Jumper + Driver || 0 (slow), 2(fast). Driver sets a mode per drive || '''Notes:''' Doesn't support ECHS or LBA<br />'''Detection:''' Config window on <code>1F0h</code>/<code>1F1h</code> (opened by reads of <code>1F3h</code>, <code>1F2h</code>, <code>3F6h</code>); register 5 &amp; <code>E0h</code> = <code>60h</code><br />'''Timing registers:''' Per-drive registers through the <code>1F0h</code>/<code>1F1h</code> window<br />'''Examined:''' LION3.SYS
|-
|-
| OPTI || 82C611 || Early 93 || 2 || PIO-3 ||  || Jumper ||  || '''Notes:''' Probably programmed the same way as the 82C611A; to be tested (Douglar)<br />'''Other names:''' Opti VIC (VIC = Vesa Ide Controller)
| OPTI || 82C611 || Early 93 || 2 || PIO-3 ||  || Jumper ||  || '''Notes:''' Probably programmed the same way as the 82C611A; to be tested (Douglar)<br />'''Other names:''' Opti VIC (VIC = Vesa Ide Controller)
|-
|-
| OPTI || 82C611A || Late 94 || 2 || PIO-3 || Card || Jumper + Driver (was: Jumper) || 0 (slow), 3 (fast). SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz || '''Other names:''' Opti VIC (VIC = Vesa Ide Controller)<br />'''Detection:''' <code>1F3h</code> echoes <code>C0h</code>; then <code>in 1F1h</code> ×2, <code>out 1F2h,03h</code> (config mode), <code>1F3h</code> changes, <code>out 1F2h,83h</code><br />'''Timing registers:''' In config mode: <code>1F3h</code> selects the drive bank, <code>1F1h</code> = write timing, <code>1F6h</code> = setup and read bank, <code>1F0h</code> = read timing, <code>1F5h</code> bits 0-1 = bus-clock strap. Linux pata_legacy 5.15 uses the same sequence for the 82C611A<br />'''Examined:''' optivic.sys 1.0, opti-pio.exe, opti-set.exe (drivers don't name the chip)
| OPTI || 82C611A || Late 94 || 2 || PIO-3 || Card || Jumper + Driver || 0 (slow), 3 (fast). SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz || '''Other names:''' Opti VIC (VIC = Vesa Ide Controller)<br />'''Detection:''' <code>1F3h</code> echoes <code>C0h</code>; then <code>in 1F1h</code> ×2, <code>out 1F2h,03h</code> (config mode), <code>1F3h</code> changes, <code>out 1F2h,83h</code><br />'''Timing registers:''' In config mode: <code>1F3h</code> selects the drive bank, <code>1F1h</code> = write timing, <code>1F6h</code> = setup and read bank, <code>1F0h</code> = read timing, <code>1F5h</code> bits 0-1 = bus-clock strap. Linux pata_legacy 5.15 uses the same sequence for the 82C611A<br />'''Examined:''' optivic.sys 1.0, opti-pio.exe, opti-set.exe (drivers don't name the chip)
|-
|-
| PiC || 1288A-125 || Late 93 || 1 || PIO-2 || Yes || Jumper || 0 (slow), 3 (fast) || '''Notes:''' Driver Not found yet<br />'''Other names:''' VIDE-1
| PiC || 1288A-125 || Late 93 || 1 || PIO-2 || Yes || Jumper || 0 (slow), 3 (fast) || '''Notes:''' Driver Not found yet<br />'''Other names:''' VIDE-1
Line 64: Line 64:
| UMC || UM82C871F || Mid 93 || 1 || PIO-3 ||  || Jumper || Best speed: AT:3 RT:4 || '''Notes:''' Driver only uses standard IDE commands; its F5 setup only toggles multi-sector mode<br />'''Examined:''' UM82C871F.SYS
| UMC || UM82C871F || Mid 93 || 1 || PIO-3 ||  || Jumper || Best speed: AT:3 RT:4 || '''Notes:''' Driver only uses standard IDE commands; its F5 setup only toggles multi-sector mode<br />'''Examined:''' UM82C871F.SYS
|-
|-
| UMC || UM85C418F || Late 93 || 1 || PIO-2 ||  || Jumper; driver overrides for 28 listed drives (was: Jumper) || Best speed: AT:5 RT:9 || '''Notes:''' Combo IDE &amp; VGA controller. The driver writes register <code>D1h</code> only when every drive is in its table<br />'''Other names:''' Stability issues at fastest speeds<br />'''Detection:''' None: <code>108h</code>/<code>109h</code> unlocked with <code>5Ah</code>, no ID read back<br />'''Timing registers:''' Register <code>D1h</code> through index <code>108h</code>/data <code>109h</code> (one value for both drives)<br />'''Examined:''' UM85C418F.SYS 1.07
| UMC || UM85C418F || Late 93 || 1 || PIO-2 ||  || Jumper; driver overrides for 28 listed drives || Best speed: AT:5 RT:9 || '''Notes:''' Combo IDE &amp; VGA controller. The driver writes register <code>D1h</code> only when every drive is in its table<br />'''Other names:''' Stability issues at fastest speeds<br />'''Detection:''' None: <code>108h</code>/<code>109h</code> unlocked with <code>5Ah</code>, no ID read back<br />'''Timing registers:''' Register <code>D1h</code> through index <code>108h</code>/data <code>109h</code> (one value for both drives)<br />'''Examined:''' UM85C418F.SYS 1.07
|-
|-
| Winbond || W83759F || Early 94 || 2 || PIO-2 ||  || Jumper || 600ns, 500ns, 400ns, 240ns || '''Notes:''' winbond_port (Linux pata_legacy parameter; default base <code>130h</code>, alternate <code>1B0h</code>)<br />'''Other names:''' Same probe as the W83759AF? WBIDE reads a revision letter; DOSEIDE needs revision B or later. Linux only programs the W83759A, after turning off jumper mode (register <code>81h</code> bit 7). F = package type (Douglar)<br />'''Detection:''' unknown
| Winbond || W83759F || Early 94 || 2 || PIO-2 ||  || Jumper || 600ns, 500ns, 400ns, 240ns || '''Notes:''' winbond_port (Linux pata_legacy parameter; default base <code>130h</code>, alternate <code>1B0h</code>)<br />'''Other names:''' Same probe as the W83759AF? WBIDE reads a revision letter; DOSEIDE needs revision B or later. Linux only programs the W83759A, after turning off jumper mode (register <code>81h</code> bit 7). F = package type (Douglar)<br />'''Detection:''' unknown

Revision as of 19:41, 12 November 2026

Full VL-bus IDE chip list

Software-configured

Brand Chip Date IDE Ports Fastest Mode IO RDY Internal Strobes Config Method MR BIOS Support XUB Support Speed Settings Notes
ADD2 DW729 Late 93 2 PIO-3 Driver Setup configures per drive Notes: Driver Options: S/00 R/00 W/00 M/00 P/00. Driver code is XOR-encrypted
Other names: Dataworld DW729
Detection: Bases 100h-1C0h: out base,85h unlock, register 0Ah reads 41h ('A'). Genuine part: register 17h = B5h
Timing registers: Registers 80h-87h at base+1 after each 85h unlock
Examined: ADD_IDE.SYS 1.03
Appian ADI/2 Mid 93 1 PIO-4 Yes Yes Driver 3.21 ctime=, dtime= (also c=, d=, s=, m=) Notes: flexidrv.sys from Adaptec is best
Other names: ALi M5213; AIC-25VL0x; CL-PD7220. FLEXIDRV also drives the AIC-25PC10 (VL-bus or PCI)
Detection: Ports 35h/B5h must differ from the PIC masks at 21h/A1h. Then an ID echo at 0AD4h, 34h or B4h: ID 38h+ = AIC-25PC10 (VL-bus mode), lower = AIC-25VL01. The PCI 25PC10 is Appian 1097:0038
Timing registers: ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7-4, recovery clocks in bits 3-0. 7/12: address setup. 1: config; 13: revision
Examined: FLEXIDRV.SYS 2.14
Atronics IDE-2015PL Late 94 2 PIO-4 Driver /Dx:Px where x= 0-4. /T:25/33/40/50 picks the bus-clock table Notes: 2015PL.SYS /Dx:P4
Other names: DTC 803 (sticker on the 2015PL; VL DTC 2278S/D/D Plus/E/B and PCI 2130D)
Detection: Index E0h/data E4h, then B0h/B4h; register echo with 3F6h reads between accesses
Timing registers: One register per drive through the same index/data pair. 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25-50 MHz; /T:66 reads past the tables (bug). Linux dtc2278.c writes A0h/C3h for PIO 3+ at B0h/B4h
Examined: 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A
CMD PCI0640B Late 94 2 PIO-4 Yes Yes Driver 3.21 /PIOMODE:X where x= 0-4. CMD640X.VL 2.09 uses /A<MHz>, /O<port><drive><mode>, /H Notes: Stability issues at fastest speeds. Hidden switches /CMD, /FOO:BAR
Detection: Index 178h/data 17Ch (else 78h/7Ch): register 50h not 00h/FFh, bit 5 set; register 5Bh echoes BDh
Timing registers: Registers 51h-58h; per-drive clocks computed from /A<MHz>
Examined: CMD640X.VL 2.09
Promise PDC-20230c Late 93 1 PIO-3 Yes Yes Driver 3.21 Yes 1(slow), 8 (fast), A (iordy). The PROMISE.SYS 3.3 README lists levels 0-8. Config-mode 1F3h speeds 0-7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. Levels 0-8 confirmed (Douglar); PROMISE.SYS has 9-entry tables, one per level Notes: PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (Douglar)
Other names: Code name VG3, TurboChip C (Soucek)
Detection: Config-mode unlock on the IDE ports: in 1F5h, set 1F2h bit 7, in 1F2h, in 3F6h ×2, in 1F2h ×3; bit 7 reads back clear = Promise
Timing registers: Index 1F8h/data 1F9h: registers 2n/2n+1 get a word from one of four tables chosen by the measured bus speed. Register 7 = transfer status. No chip ID read; same code for every Promise chip. Four 9-entry tables (one per measured bus class), shared by all three Promise chips
Examined: PROMISE.SYS 3.3 (PROMISE.SYS 3.3; it doesn't name the chip)
Promise PDC-20630 Mid 94 2 WDMA2 Yes Yes Driver 3.21 Yes 1(slow), 8 (fast), A (iordy) Notes: Internal PIO Clock. PROMISE.SYS 3.3 issues READ/WRITE DMA (C8h/CAh) and moves the data to memory by PIO from 1F0h. PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (Douglar)
Other names: WDMA2 is chip-to-pata, no DMA to system RAM. PROMISE.SYS 3.3 only ever sets the drive to multiword DMA mode 1 (SET FEATURES 21h, DMA levels 7-8); it never sends 22h
Detection: As PDC-20230c, then 1F4h bit 3 makes 1F8h read back its index (bits 0-2)
Timing registers: 1F3h speed as PDC-20230c, plus four timing registers through 1F8h/1F9h (enabled by 1F4h bit 3)
Examined: PROMISE.SYS 3.3 (same code path; no chip check)
QDI Vision 6500 Mid 93 1 PIO-2 Driver Yes Setup configures per drive. Driver picks a timing class from its drive table Detection: Register 31h (or B1h): upper nibble C0h; bit 3 set = disabled
Timing registers: One timing byte at 30h/B0h (active bits 0-2, recovery bits 4-7)
Examined: QD6500.SYS 2.4
QDI Vision 6580 Late 94 2 PIO-4 Card Half Driver Yes Setup configures per drive Notes: PIO timing based on bus clock
Detection: Register 31h (or B1h): upper nibble A0h or 50h
Timing registers: As QD6500, plus secondary-channel timing
Examined: qd6580.sys 3.7
SIS 83C601 Early 95 1 PIO-4? Yes Yes Driver 3.21 Waitstate 1 (fast) -7 (slow) Notes: Newer than the 83C611 Tyan Driver is 1995-04. Early 95 is the earliest fab date seen. SIIG also shipped its own drivers for this chip (Douglar)
Other names: PCI ID 1039:0601 (SIS611.SYS 08/94 already checks for it)
Detection: in 1F3h; in 1F2h ×4; out 1F2h,F3h; 1F2h reads D3h
Timing registers: 1F2h ← F0h + (wait state − 1) after the same unlock
Examined: S134XM1.SYS 2.0, S134XD1.COM 3.5 (drivers don't name the chip; wait-state range matches)
SIS 83C611 Late 93 1 PIO-4? Yes Driver 3.21 Wait state 0-7 for each channel Notes: Older than the 83C601
Other names: Driver banner says "VL/PCI-IDE"; the PCI check is unused
Detection: Same 1F2h sequence (0C14h)
Timing registers: 1F2h: F3h, B5h, then computed wait states
Examined: SIS611.SYS 2.11
UMC UM8672F Late 94 1 PIO-2 Driver Speeds 0 (slow) -11 (fast) Notes: PIO-4 with Modded Driver. Driver calls speed 10 the "proper speed" for Enhanced IDE drives
Other names: UM82C872F
Detection: None: 108h/109h unlocked with 5Ah, no ID read back
Timing registers: Registers D0h-DDh through index 108h/data 109h; all set to CBh (slowest) first. Six 12-entry tables in UM8672.SYS (chip ID A0h/A2h × 3 bus-speed classes). Linux umc8672.c uses the A0h slow-bus values (UMC-supplied). See TIMING.md, "Timing tables in the drivers"
Examined: UM8672.SYS 2.1
VIA VT83C461 Mid 94 2 PIO-2 Yes Driver PIO_TIME=, DMA_TIME=, SET_DMAM= Notes: Has a BIOS / AV140 / AV150 / AV300
Other names: Driver also covers the VT82C496G
Detection: Index A8h/data A9h: register 00h upper nibble 70h/90h, register 71h bit 0 set
Timing registers: Registers 71h (IDE enable), 93h (timing/mode)
Examined: VIAIDE.SYS 4.02
Winbond W83759AF Early 95 2 PIO-3 Yes Yes Driver /D0:13 (speeds 0-13) Notes: software speed config and "advanced mode". Measures the bus clock with the PC timer. A hacked driver that enables PIO 4 is reported to exist (Douglar)
Other names: DTC 2278E Rev W. F = package type; the A suggests a silicon respin (Douglar)
Detection: Bases 4B0h/5B0h… then 430h/530h…: 63h written at base+0 reads back at base+0Ch; register 87h low nibble = revision; register 80h bit 7 set
Timing registers: Index base+4, data base+8
Examined: WBIDE.EXE, DOSEIDE.SYS 2.1A (at 5B0h only)
Micronics MIC491 Mid 93 1 unknown BIOS Setup IDE Speed: Normal / Medium / Fast (register 104h = 69h / 67h / 63h) Notes: No driver; the system BIOS sets it
Other names: Onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS"
Detection: None. The BIOS only checks that no other IDE controller answers at 1F0h
Timing registers: out 9Ch,7Fh opens ports 102h-106h; 104h = speed, 102h bit 0 = IDE on
Examined: GJX30G BIOS 09-24-93

Jumper-configured

Brand Chip Date IDE Ports Fastest Mode IO RDY Config Method Speed Settings Notes
Chaintech CT9000 Late 93 1 PIO-3 Yes Jumper 0-3 Notes: Not found yet: ct9000.zip
DTC DTC 805 Early 94 1 PIO-2 Jumper 3.9MB/s - 7.2MB/s Notes: DOSEIDE.SYS has no code for it; it only shows the drive's reported rate
Other names: DTC 2278VL, jumpers W1-W5
Examined: DOSEIDE.SYS 2.1A
GoldStar GM82C711 Early 93 1 PIO-3 Jumper 0-7 Notes: GS_DOS.SYS never writes a timing register. The same GS_DOS.SYS works on the GM82C712 (Douglar)
Other names: Not a PC Chips 82C711
Detection: unknown
Examined: GS_DOS.SYS 1.21 (driver doesn't name the chip)
GoldStar GM82C712 Mid 95 1 PIO-4 Yes Jumper 0-7 Notes: GS_DOS.SYS works on it too (Douglar)
Other names: CompassLab CL3202. Not a PC Chips 82C712
Detection: unknown
Examined: GS_DOS.SYS 1.21 (Douglar: same driver as GM82C711)
Holtek HT6560A Late 94 2 PIO-2 Jumper 0 (slow), 3 (fast) Notes: Driver Not found yet
Holtek HT6560B Early 95 2 PIO-3 Yes Jumper + Driver 0 (slow), 3 (fast). Driver /Dn=rt,at: recovery 2-16, active 2-15 bus clocks Notes: Driver allows AT:2 RT:2
Detection: 3E6h handshake: after three out 3E6h,0 / in 3E6h rounds some of bits 0-5 read back clear; on the fourth all six are set
Timing registers: Four reads of 3E6h, then config byte to 3E6h and timing byte (recovery << 4 OR active) to 1F6h. Linux pata_legacy 5.15 agrees
Examined: HTIDE.SYS 2.41
Lion Lion 3+ Mid 95 2 PIO-3 Jumper + Driver 0 (slow), 2(fast). Driver sets a mode per drive Notes: Doesn't support ECHS or LBA
Detection: Config window on 1F0h/1F1h (opened by reads of 1F3h, 1F2h, 3F6h); register 5 & E0h = 60h
Timing registers: Per-drive registers through the 1F0h/1F1h window
Examined: LION3.SYS
OPTI 82C611 Early 93 2 PIO-3 Jumper Notes: Probably programmed the same way as the 82C611A; to be tested (Douglar)
Other names: Opti VIC (VIC = Vesa Ide Controller)
OPTI 82C611A Late 94 2 PIO-3 Card Jumper + Driver 0 (slow), 3 (fast). SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz Other names: Opti VIC (VIC = Vesa Ide Controller)
Detection: 1F3h echoes C0h; then in 1F1h ×2, out 1F2h,03h (config mode), 1F3h changes, out 1F2h,83h
Timing registers: In config mode: 1F3h selects the drive bank, 1F1h = write timing, 1F6h = setup and read bank, 1F0h = read timing, 1F5h bits 0-1 = bus-clock strap. Linux pata_legacy 5.15 uses the same sequence for the 82C611A
Examined: optivic.sys 1.0, opti-pio.exe, opti-set.exe (drivers don't name the chip)
PiC 1288A-125 Late 93 1 PIO-2 Yes Jumper 0 (slow), 3 (fast) Notes: Driver Not found yet
Other names: VIDE-1
Promise PDC-20230b Mid 93 1 PIO-3 Jumper 0 (slow), 2(fast) Notes: Works with the PROMISE.SYS 3.3 drivers (Douglar). PROMISE.SYS 3.3 supports it (Douglar)
Other names: CompassLab CL3201 (9314) ? Code name TurboChip B; jumper speeds 0, 1, 2 (Soucek)
Detection: No config mode. Write 55h to 1F2h, read it three times back to back: a 20230-B returns 00h on the third read (Soucek; also unreached code in PROMISE.SYS at 2D3Bh). Needs the same three reads as a "VLB sync" before 32-bit I/O
Timing registers: - (jumpers)
Examined: PROMISE.SYS 3.3
UMC UM82C871F Mid 93 1 PIO-3 Jumper Best speed: AT:3 RT:4 Notes: Driver only uses standard IDE commands; its F5 setup only toggles multi-sector mode
Examined: UM82C871F.SYS
UMC UM85C418F Late 93 1 PIO-2 Jumper; driver overrides for 28 listed drives Best speed: AT:5 RT:9 Notes: Combo IDE & VGA controller. The driver writes register D1h only when every drive is in its table
Other names: Stability issues at fastest speeds
Detection: None: 108h/109h unlocked with 5Ah, no ID read back
Timing registers: Register D1h through index 108h/data 109h (one value for both drives)
Examined: UM85C418F.SYS 1.07
Winbond W83759F Early 94 2 PIO-2 Jumper 600ns, 500ns, 400ns, 240ns Notes: winbond_port (Linux pata_legacy parameter; default base 130h, alternate 1B0h)
Other names: Same probe as the W83759AF? WBIDE reads a revision letter; DOSEIDE needs revision B or later. Linux only programs the W83759A, after turning off jumper mode (register 81h bit 7). F = package type (Douglar)
Detection: unknown

No configuration software found

No driver or setup utility has been found for these chips.

Brand Chip Date IDE Ports Notes
QDI Vision 5500 Early 1 Not found yet: QDI5500.sys. The only reference to this chip found so far is in TH99; Linux pata_legacy has no QD5500 support (only QD6500/6580/6580DP)
Tans TS8310 Mid 94 2 Not found yet: ts8310.zip, BIOS was generic. Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997), v2.10 ">8.4GB" (1999), and SIIG v3.10, which is TANS v2.00 with only the name changed (18 bytes differ). All use only the standard IDE ports at 1F0h/170h/1E8h/168h: no chip detection, no timing writes, and 16-bit rep insw/outsw only (no 32-bit I/O)
Tans TS8310A Late 94 2 Not found yet: ts8310.zip, BIOS was generic. Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997), v2.10 ">8.4GB" (1999), and SIIG v3.10, which is TANS v2.00 with only the name changed (18 bytes differ). All use only the standard IDE ports at 1F0h/170h/1E8h/168h: no chip detection, no timing writes, and 16-bit rep insw/outsw only (no 32-bit I/O)
Mach Speed GTK6189 Early 94 1 No driver found. VLB card with a Cirrus CL-GD5428 VGA; the 40-pin IDE header has never been seen fitted, and some traces run to the VGA chip. The card ROM is a standard Cirrus VGA BIOS with nothing about IDE. Jumper positions are unpopulated except one that is hard-shorted, probably to disable the IDE function. Possibly IDE was dropped late in the design (Douglar's observation)
Opus Op VIC1 Late 93 1 No driver found. Op VIC (VIC = Vesa Ide Controller)
Opus Op VIC3 Early 94 2 Op VIC (VIC = Vesa Ide Controller)