VLB IDE Controllers: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
|||
| Line 9: | Line 9: | ||
{| class="wikitable sortable" | {| class="wikitable sortable" | ||
! Brand !! Chip !! Date !! IDE Ports !! Fastest Mode !! IO RDY !! Internal Strobes !! Config Method !! MR BIOS Support !! XUB Support !! Speed Settings !! | ! Brand !! Chip !! Date !! IDE Ports !! Fastest Mode !! IO RDY !! Internal Strobes !! Config Method !! MR BIOS Support !! XUB Support !! Speed Settings !! Notes | ||
|- | |- | ||
| ADD2 || DW729 || Late 93 || 2 || PIO-3 || || || Driver || || || Setup configures per drive || Driver Options: S/00 R/00 W/00 M/00 P/00. † Driver code is XOR-encrypted | | ADD2 || DW729 || Late 93 || 2 || PIO-3 || || || Driver || || || Setup configures per drive || '''Notes:''' Driver Options: S/00 R/00 W/00 M/00 P/00. † Driver code is XOR-encrypted<br />'''Other names:''' Dataworld DW729<br />'''Detection:''' Bases <code>100h</code>-<code>1C0h</code>: <code>out base,85h</code> unlock, register <code>0Ah</code> reads <code>41h</code> ('A'). Genuine part: register <code>17h</code> = <code>B5h</code><br />'''Timing registers:''' Registers <code>80h</code>-<code>87h</code> at base+1 after each <code>85h</code> unlock<br />'''Examined:''' ADD_IDE.SYS 1.03 | ||
|- | |- | ||
| Appian || ADI/2 || Mid 93 || 1 || PIO-4 || Yes || Yes || Driver || 3.21 || || † <code>ctime=</code>, <code>dtime=</code> (also <code>c=</code>, <code>d=</code>, <code>s=</code>, <code>m=</code>) [No flags] || flexidrv.sys from Adaptec is best | | Appian || ADI/2 || Mid 93 || 1 || PIO-4 || Yes || Yes || Driver || 3.21 || || † <code>ctime=</code>, <code>dtime=</code> (also <code>c=</code>, <code>d=</code>, <code>s=</code>, <code>m=</code>) [No flags] || '''Notes:''' flexidrv.sys from Adaptec is best<br />'''Other names:''' ALi M5213; AIC-25VL0x; CL-PD7220. † FLEXIDRV also drives the AIC-25PC10 (VL-bus or PCI)<br />'''Detection:''' Ports <code>35h</code>/<code>B5h</code> must differ from the PIC masks at <code>21h</code>/<code>A1h</code>. † Then an ID echo at <code>0AD4h</code>, <code>34h</code> or <code>B4h</code>: ID <code>38h</code>+ = AIC-25PC10 (VL-bus mode), lower = AIC-25VL01. The PCI 25PC10 is Appian <code>1097:0038</code><br />'''Timing registers:''' † ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7-4, recovery clocks in bits 3-0. 7/12: address setup. 1: config; 13: revision<br />'''Examined:''' FLEXIDRV.SYS 2.14 | ||
|- | |- | ||
| Atronics || IDE-2015PL || Late 94 || 2 || PIO-4 || || || Driver || || || /Dx:Px where x= 0-4. † <code>/T:25/33/40/50</code> picks the bus-clock table || 2015PL.SYS /Dx:P4 | | Atronics || IDE-2015PL || Late 94 || 2 || PIO-4 || || || Driver || || || /Dx:Px where x= 0-4. † <code>/T:25/33/40/50</code> picks the bus-clock table || '''Notes:''' 2015PL.SYS /Dx:P4<br />'''Other names:''' DTC 803 † (sticker on the 2015PL; VL DTC 2278S/D/D Plus/E/B and PCI 2130D)<br />'''Detection:''' Index <code>E0h</code>/data <code>E4h</code>, then <code>B0h</code>/<code>B4h</code>; register echo with <code>3F6h</code> reads between accesses<br />'''Timing registers:''' One register per drive through the same index/data pair. † 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25-50 MHz; <code>/T:66</code> reads past the tables (bug). Linux <code>dtc2278.c</code> writes <code>A0h</code>/<code>C3h</code> for PIO 3+ at <code>B0h</code>/<code>B4h</code><br />'''Examined:''' 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A | ||
|- | |- | ||
| CMD || PCI0640B || Late 94 || 2 || PIO-4 || Yes || Yes || Driver || 3.21 || || /PIOMODE:X where x= 0-4. † CMD640X.VL 2.09 uses <code>/A<MHz></code>, <code>/O<port><drive><mode></code>, <code>/H</code> || Stability issues at fastest speeds. † Hidden switches <code>/CMD</code>, <code>/FOO:BAR</code> | | CMD || PCI0640B || Late 94 || 2 || PIO-4 || Yes || Yes || Driver || 3.21 || || /PIOMODE:X where x= 0-4. † CMD640X.VL 2.09 uses <code>/A<MHz></code>, <code>/O<port><drive><mode></code>, <code>/H</code> || '''Notes:''' Stability issues at fastest speeds. † Hidden switches <code>/CMD</code>, <code>/FOO:BAR</code><br />'''Detection:''' Index <code>178h</code>/data <code>17Ch</code> (else <code>78h</code>/<code>7Ch</code>): register <code>50h</code> not <code>00h</code>/<code>FFh</code>, bit 5 set; register <code>5Bh</code> echoes <code>BDh</code><br />'''Timing registers:''' Registers <code>51h</code>-<code>58h</code>; per-drive clocks computed from <code>/A<MHz></code><br />'''Examined:''' CMD640X.VL 2.09 | ||
|- | |- | ||
| Promise || PDC-20230c || Late 93 || 1 || PIO-3 || Yes || Yes || Driver || 3.21 || Yes || 1(slow), 8 (fast), A (iordy). † The PROMISE.SYS 3.3 README lists levels 0-8. † Config-mode <code>1F3h</code> speeds 0-7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. † Levels 0-8 confirmed (owner); PROMISE.SYS has 9-entry tables, one per level || † PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (owner) | | Promise || PDC-20230c || Late 93 || 1 || PIO-3 || Yes || Yes || Driver || 3.21 || Yes || 1(slow), 8 (fast), A (iordy). † The PROMISE.SYS 3.3 README lists levels 0-8. † Config-mode <code>1F3h</code> speeds 0-7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. † Levels 0-8 confirmed (owner); PROMISE.SYS has 9-entry tables, one per level || '''Notes:''' † PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (owner)<br />'''Other names:''' † Code name VG3, TurboChip C (Soucek)<br />'''Detection:''' † Config-mode unlock on the IDE ports: <code>in 1F5h</code>, set <code>1F2h</code> bit 7, <code>in 1F2h</code>, <code>in 3F6h</code> ×2, <code>in 1F2h</code> ×3; bit 7 reads back clear = Promise<br />'''Timing registers:''' Index <code>1F8h</code>/data <code>1F9h</code>: registers 2n/2n+1 get a word from one of four tables chosen by the measured bus speed. Register 7 = transfer status. † No chip ID read; same code for every Promise chip. † Four 9-entry tables (one per measured bus class), shared by all three Promise chips<br />'''Examined:''' PROMISE.SYS 3.3 (PROMISE.SYS 3.3; it doesn't name the chip) | ||
|- | |- | ||
| Promise || PDC-20630 || Mid 94 || 2 || WDMA2 || Yes || Yes || Driver || 3.21 || Yes || 1(slow), 8 (fast), A (iordy) || Internal PIO Clock. † PROMISE.SYS 3.3 issues READ/WRITE DMA (<code>C8h</code>/<code>CAh</code>) and moves the data to memory by PIO from <code>1F0h</code>. † PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (owner) | | Promise || PDC-20630 || Mid 94 || 2 || WDMA2 || Yes || Yes || Driver || 3.21 || Yes || 1(slow), 8 (fast), A (iordy) || '''Notes:''' Internal PIO Clock. † PROMISE.SYS 3.3 issues READ/WRITE DMA (<code>C8h</code>/<code>CAh</code>) and moves the data to memory by PIO from <code>1F0h</code>. † PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (owner)<br />'''Other names:''' WDMA2 is chip-to-pata, no DMA to system RAM. † PROMISE.SYS 3.3 only ever sets the drive to multiword DMA '''mode 1''' (SET FEATURES <code>21h</code>, DMA levels 7-8); it never sends <code>22h</code><br />'''Detection:''' † As PDC-20230c, then <code>1F4h</code> bit 3 makes <code>1F8h</code> read back its index (bits 0-2)<br />'''Timing registers:''' † <code>1F3h</code> speed as PDC-20230c, plus four timing registers through <code>1F8h</code>/<code>1F9h</code> (enabled by <code>1F4h</code> bit 3)<br />'''Examined:''' PROMISE.SYS 3.3 (same code path; no chip check) | ||
|- | |- | ||
| QDI || Vision 6500 || Mid 93 || 1 || PIO-2 || || || Driver || || Yes || Setup configures per drive. † Driver picks a timing class from its drive table || | | QDI || Vision 6500 || Mid 93 || 1 || PIO-2 || || || Driver || || Yes || Setup configures per drive. † Driver picks a timing class from its drive table || '''Detection:''' Register <code>31h</code> (or <code>B1h</code>): upper nibble <code>C0h</code>; bit 3 set = disabled<br />'''Timing registers:''' One timing byte at <code>30h</code>/<code>B0h</code> (active bits 0-2, recovery bits 4-7)<br />'''Examined:''' QD6500.SYS 2.4 | ||
|- | |- | ||
| QDI || Vision 6580 || Late 94 || 2 || PIO-4 || Card || Half || Driver || || Yes || Setup configures per drive || PIO timing based on bus clock | | QDI || Vision 6580 || Late 94 || 2 || PIO-4 || Card || Half || Driver || || Yes || Setup configures per drive || '''Notes:''' PIO timing based on bus clock<br />'''Detection:''' Register <code>31h</code> (or <code>B1h</code>): upper nibble <code>A0h</code> or <code>50h</code><br />'''Timing registers:''' As QD6500, plus secondary-channel timing<br />'''Examined:''' qd6580.sys 3.7 | ||
|- | |- | ||
| SIS || 83C601 || Early 95 || 1 || PIO-4? || Yes || Yes || Driver || 3.21 || || Waitstate 1 (fast) -7 (slow) || Newer than the 83C611 Tyan Driver is 1995-04. Early 95 is the earliest fab date seen. † SIIG also shipped its own drivers for this chip (owner) | | SIS || 83C601 || Early 95 || 1 || PIO-4? || Yes || Yes || Driver || 3.21 || || Waitstate 1 (fast) -7 (slow) || '''Notes:''' Newer than the 83C611 Tyan Driver is 1995-04. Early 95 is the earliest fab date seen. † SIIG also shipped its own drivers for this chip (owner)<br />'''Other names:''' † PCI ID <code>1039:0601</code> (SIS611.SYS 08/94 already checks for it)<br />'''Detection:''' <code>in 1F3h</code>; <code>in 1F2h</code> ×4; <code>out 1F2h,F3h</code>; <code>1F2h</code> reads <code>D3h</code><br />'''Timing registers:''' <code>1F2h</code> ← <code>F0h</code> + (wait state − 1) after the same unlock<br />'''Examined:''' S134XM1.SYS 2.0, S134XD1.COM 3.5 (drivers don't name the chip; wait-state range matches) | ||
|- | |- | ||
| SIS || 83C611 || Late 93 || 1 || PIO-4? || Yes || || Driver || 3.21 || || † Wait state 0-7 for each channel || Older than the 83C601 | | SIS || 83C611 || Late 93 || 1 || PIO-4? || Yes || || Driver || 3.21 || || † Wait state 0-7 for each channel || '''Notes:''' Older than the 83C601<br />'''Other names:''' † Driver banner says "VL/PCI-IDE"; the PCI check is unused<br />'''Detection:''' Same <code>1F2h</code> sequence (<code>0C14h</code>)<br />'''Timing registers:''' <code>1F2h</code>: <code>F3h</code>, <code>B5h</code>, then computed wait states<br />'''Examined:''' SIS611.SYS 2.11 | ||
|- | |- | ||
| UMC || UM8672F || Late 94 || 1 || PIO-2 || || || Driver || || || Speeds 0 (slow) -11 (fast) || PIO-4 with Modded Driver. † Driver calls speed 10 the "proper speed" for Enhanced IDE drives | | UMC || UM8672F || Late 94 || 1 || PIO-2 || || || Driver || || || Speeds 0 (slow) -11 (fast) || '''Notes:''' PIO-4 with Modded Driver. † Driver calls speed 10 the "proper speed" for Enhanced IDE drives<br />'''Other names:''' UM82C872F<br />'''Detection:''' None: <code>108h</code>/<code>109h</code> unlocked with <code>5Ah</code>, no ID read back<br />'''Timing registers:''' Registers <code>D0h</code>-<code>DDh</code> through index <code>108h</code>/data <code>109h</code>; all set to <code>CBh</code> (slowest) first. † Six 12-entry tables in UM8672.SYS (chip ID <code>A0h</code>/<code>A2h</code> × 3 bus-speed classes). Linux <code>umc8672.c</code> uses the <code>A0h</code> slow-bus values (UMC-supplied). See TIMING.md, "Timing tables in the drivers"<br />'''Examined:''' UM8672.SYS 2.1 | ||
|- | |- | ||
| VIA || VT83C461 || Mid 94 || 2 || PIO-2 || Yes || || Driver || || || † <code>PIO_TIME=</code>, <code>DMA_TIME=</code>, <code>SET_DMAM=</code> || Has a BIOS / AV140 / AV150 / AV300 | | VIA || VT83C461 || Mid 94 || 2 || PIO-2 || Yes || || Driver || || || † <code>PIO_TIME=</code>, <code>DMA_TIME=</code>, <code>SET_DMAM=</code> || '''Notes:''' Has a BIOS / AV140 / AV150 / AV300<br />'''Other names:''' † Driver also covers the VT82C496G<br />'''Detection:''' Index <code>A8h</code>/data <code>A9h</code>: register <code>00h</code> upper nibble <code>70h</code>/<code>90h</code>, register <code>71h</code> bit 0 set<br />'''Timing registers:''' Registers <code>71h</code> (IDE enable), <code>93h</code> (timing/mode)<br />'''Examined:''' VIAIDE.SYS 4.02 | ||
|- | |- | ||
| Winbond || W83759AF || Early 95 || 2 || PIO-4 † (WBIDE.TXT's ns table makes speed 13 = PIO 3 at 33 MHz) || Yes || Yes || Driver || || || /D0:13 (speeds 0-13) || software speed config and "advanced mode". † Measures the bus clock with the PC timer. † A hacked driver that enables PIO 4 is reported to exist (owner) | | Winbond || W83759AF || Early 95 || 2 || PIO-4 † (WBIDE.TXT's ns table makes speed 13 = PIO 3 at 33 MHz) || Yes || Yes || Driver || || || /D0:13 (speeds 0-13) || '''Notes:''' software speed config and "advanced mode". † Measures the bus clock with the PC timer. † A hacked driver that enables PIO 4 is reported to exist (owner)<br />'''Other names:''' † DTC 2278E Rev W. † F = package type; the A suggests a silicon respin (owner)<br />'''Detection:''' Bases <code>4B0h</code>/<code>5B0h</code>… then <code>430h</code>/<code>530h</code>…: <code>63h</code> written at base+0 reads back at base+0Ch; register <code>87h</code> low nibble = revision; register <code>80h</code> bit 7 set<br />'''Timing registers:''' Index base+4, data base+8<br />'''Examined:''' WBIDE.EXE, DOSEIDE.SYS 2.1A (at <code>5B0h</code> only) | ||
|- | |- | ||
| Micronics || MIC491 || Mid 93 || 1 || ? || || || † BIOS Setup || || || † IDE Speed: Normal / Medium / Fast (register <code>104h</code> = <code>69h</code> / <code>67h</code> / <code>63h</code>) || † No driver; the system BIOS sets it | | Micronics || MIC491 || Mid 93 || 1 || ? || || || † BIOS Setup || || || † IDE Speed: Normal / Medium / Fast (register <code>104h</code> = <code>69h</code> / <code>67h</code> / <code>63h</code>) || '''Notes:''' † No driver; the system BIOS sets it<br />'''Other names:''' † Onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS"<br />'''Detection:''' † None. The BIOS only checks that no other IDE controller answers at <code>1F0h</code><br />'''Timing registers:''' † <code>out 9Ch,7Fh</code> opens ports <code>102h</code>-<code>106h</code>; <code>104h</code> = speed, <code>102h</code> bit 0 = IDE on<br />'''Examined:''' GJX30G BIOS 09-24-93 | ||
|} | |} | ||
| Line 43: | Line 43: | ||
{| class="wikitable sortable" | {| class="wikitable sortable" | ||
! Brand !! Chip !! Date !! IDE Ports !! Fastest Mode !! IO RDY | ! Brand !! Chip !! Date !! IDE Ports !! Fastest Mode !! IO RDY !! Config Method !! Speed Settings !! Notes | ||
|- | |- | ||
| Chaintech || CT9000 || Late 93 || 1 || PIO-3 || Yes | | Chaintech || CT9000 || Late 93 || 1 || PIO-3 || Yes || Jumper || 0-3 || '''Notes:''' Not found yet: ct9000.zip | ||
|- | |- | ||
| DTC || DTC 805 || Early 94 || 1 || PIO-2 | | DTC || DTC 805 || Early 94 || 1 || PIO-2 || || Jumper || 3.9MB/s - 7.2MB/s || '''Notes:''' † DOSEIDE.SYS has no code for it; it only shows the drive's reported rate<br />'''Other names:''' † DTC 2278VL, jumpers W1-W5<br />'''Examined:''' DOSEIDE.SYS 2.1A | ||
|- | |- | ||
| GoldStar || GM82C711 || Early 93 || 1 || PIO-3 | | GoldStar || GM82C711 || Early 93 || 1 || PIO-3 || || Jumper || 0-7 || '''Notes:''' † GS_DOS.SYS never writes a timing register. † The same GS_DOS.SYS works on the GM82C712 (owner)<br />'''Other names:''' Not a PC Chips 82C711<br />'''Detection:''' ?<br />'''Examined:''' GS_DOS.SYS 1.21 (driver doesn't name the chip) | ||
|- | |- | ||
| GoldStar || GM82C712 || Mid 95 || 1 || PIO-4 || Yes | | GoldStar || GM82C712 || Mid 95 || 1 || PIO-4 || Yes || Jumper || 0-7 || '''Notes:''' † GS_DOS.SYS works on it too (owner)<br />'''Other names:''' CompassLab CL3202. Not a PC Chips 82C712<br />'''Detection:''' ?<br />'''Examined:''' GS_DOS.SYS 1.21 (owner: same driver as GM82C711) | ||
|- | |- | ||
| Holtek || HT6560A || Late 94 || 2 || PIO-2 | | Holtek || HT6560A || Late 94 || 2 || PIO-2 || || Jumper || 0 (slow), 3 (fast) || '''Notes:''' Driver Not found yet | ||
|- | |- | ||
| Holtek || HT6560B || Early 95 || 2 || PIO-3 || Yes | | Holtek || HT6560B || Early 95 || 2 || PIO-3 || Yes || † Jumper + Driver [Jumper] || 0 (slow), 3 (fast). † Driver <code>/Dn=rt,at</code>: recovery 2-16, active 2-15 bus clocks || '''Notes:''' Driver allows AT:2 RT:2<br />'''Detection:''' <code>3E6h</code> handshake: after three <code>out 3E6h,0</code> / <code>in 3E6h</code> rounds some of bits 0-5 read back clear; on the fourth all six are set<br />'''Timing registers:''' † Four reads of <code>3E6h</code>, then config byte to <code>3E6h</code> and timing byte (recovery << 4 OR active) to <code>1F6h</code> [Timing bytes to <code>3E6h</code>]. Linux pata_legacy 5.15 agrees<br />'''Examined:''' HTIDE.SYS 2.41 | ||
|- | |- | ||
| Lion || Lion 3+ || Mid 95 || 2 || PIO-3 | | Lion || Lion 3+ || Mid 95 || 2 || PIO-3 || || † Jumper + Driver [Jumper] || 0 (slow), 2(fast). † Driver sets a mode per drive || '''Notes:''' Doesn't support ECHS or LBA<br />'''Detection:''' Config window on <code>1F0h</code>/<code>1F1h</code> (opened by reads of <code>1F3h</code>, <code>1F2h</code>, <code>3F6h</code>); register 5 & <code>E0h</code> = <code>60h</code><br />'''Timing registers:''' Per-drive registers through the <code>1F0h</code>/<code>1F1h</code> window<br />'''Examined:''' LION3.SYS | ||
|- | |- | ||
| OPTI || 82C611 || Early 93 || 2 || PIO-3 | | OPTI || 82C611 || Early 93 || 2 || PIO-3 || || Jumper || || '''Notes:''' † Probably programmed the same way as the 82C611A; to be tested (owner)<br />'''Other names:''' Opti VIC (VIC = Vesa Ide Controller) | ||
|- | |- | ||
| OPTI || 82C611A || Late 94 || 2 || PIO-3 || Card | | OPTI || 82C611A || Late 94 || 2 || PIO-3 || Card || † Jumper + Driver [Jumper] || 0 (slow), 3 (fast). † SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz || '''Other names:''' Opti VIC (VIC = Vesa Ide Controller)<br />'''Detection:''' <code>1F3h</code> echoes <code>C0h</code>; then <code>in 1F1h</code> ×2, <code>out 1F2h,03h</code> (config mode), <code>1F3h</code> changes, <code>out 1F2h,83h</code><br />'''Timing registers:''' In config mode: <code>1F3h</code> selects the drive bank, <code>1F1h</code> = write timing, <code>1F6h</code> = setup and read bank, <code>1F0h</code> = read timing, <code>1F5h</code> bits 0-1 = bus-clock strap. † Linux pata_legacy 5.15 uses the same sequence for the 82C611A<br />'''Examined:''' optivic.sys 1.0, opti-pio.exe, opti-set.exe (drivers don't name the chip) | ||
|- | |- | ||
| PiC || 1288A-125 || Late 93 || 1 || PIO-2 || Yes | | PiC || 1288A-125 || Late 93 || 1 || PIO-2 || Yes || Jumper || 0 (slow), 3 (fast) || '''Notes:''' Driver Not found yet<br />'''Other names:''' VIDE-1 | ||
|- | |- | ||
| Promise || PDC-20230b || Mid 93 || 1 || PIO-3 | | Promise || PDC-20230b || Mid 93 || 1 || PIO-3 || || Jumper || 0 (slow), 2(fast) || '''Notes:''' † Works with the PROMISE.SYS 3.3 drivers (owner). † PROMISE.SYS 3.3 supports it (owner)<br />'''Other names:''' CompassLab CL3201 (9314) ? † Code name TurboChip B; jumper speeds 0, 1, 2 (Soucek)<br />'''Detection:''' † No config mode. Write <code>55h</code> to <code>1F2h</code>, read it three times back to back: a 20230-B returns <code>00h</code> on the third read (Soucek; also unreached code in PROMISE.SYS at <code>2D3Bh</code>). Needs the same three reads as a "VLB sync" before 32-bit I/O<br />'''Timing registers:''' - (jumpers)<br />'''Examined:''' PROMISE.SYS 3.3 | ||
|- | |- | ||
| UMC || UM82C871F || Mid 93 || 1 || PIO-3 | | UMC || UM82C871F || Mid 93 || 1 || PIO-3 || || Jumper || Best speed: AT:3 RT:4 || '''Notes:''' † Driver only uses standard IDE commands; its F5 setup only toggles multi-sector mode<br />'''Examined:''' UM82C871F.SYS | ||
|- | |- | ||
| UMC || UM85C418F || Late 93 || 1 || PIO-2 | | UMC || UM85C418F || Late 93 || 1 || PIO-2 || || † Jumper; driver overrides for 28 listed drives [Jumper] || Best speed: AT:5 RT:9 || '''Notes:''' Combo IDE & VGA controller. † The driver writes register <code>D1h</code> only when every drive is in its table<br />'''Other names:''' Stability issues at fastest speeds<br />'''Detection:''' None: <code>108h</code>/<code>109h</code> unlocked with <code>5Ah</code>, no ID read back<br />'''Timing registers:''' Register <code>D1h</code> through index <code>108h</code>/data <code>109h</code> (one value for both drives)<br />'''Examined:''' UM85C418F.SYS 1.07 | ||
|- | |- | ||
| Winbond || W83759F || Early 94 || 2 || PIO-2 | | Winbond || W83759F || Early 94 || 2 || PIO-2 || || Jumper || 600ns, 500ns, 400ns, 240ns || '''Notes:''' winbond_port † (Linux pata_legacy parameter; default base <code>130h</code>, alternate <code>1B0h</code>)<br />'''Other names:''' † Same probe as the W83759AF? WBIDE reads a revision letter; DOSEIDE needs revision B or later. Linux only programs the W83759A, after turning off jumper mode (register <code>81h</code> bit 7). † F = package type (owner)<br />'''Detection:''' ? | ||
|} | |} | ||
| Line 79: | Line 79: | ||
{| class="wikitable sortable" | {| class="wikitable sortable" | ||
! Brand !! Chip !! Date !! IDE Ports !! | ! Brand !! Chip !! Date !! IDE Ports !! Notes | ||
|- | |- | ||
| QDI || Vision 5500 || Early || 1 | | QDI || Vision 5500 || Early || 1 || Not found yet: QDI5500.sys. † The only reference to this chip found so far is in TH99; Linux pata_legacy has no QD5500 support (only QD6500/6580/6580DP) | ||
|- | |- | ||
| Tans || TS8310 || Mid 94 || 2 | | Tans || TS8310 || Mid 94 || 2 || Not found yet: ts8310.zip, BIOS was generic. † Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997), v2.10 ">8.4GB" (1999), and SIIG v3.10, which is TANS v2.00 with only the name changed (18 bytes differ). All use only the standard IDE ports at 1F0h/170h/1E8h/168h: no chip detection, no timing writes, and 16-bit <code>rep insw</code>/<code>outsw</code> only (no 32-bit I/O) | ||
|- | |- | ||
| Tans || TS8310A || Late 94 || 2 | | Tans || TS8310A || Late 94 || 2 || Not found yet: ts8310.zip, BIOS was generic. † Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997), v2.10 ">8.4GB" (1999), and SIIG v3.10, which is TANS v2.00 with only the name changed (18 bytes differ). All use only the standard IDE ports at 1F0h/170h/1E8h/168h: no chip detection, no timing writes, and 16-bit <code>rep insw</code>/<code>outsw</code> only (no 32-bit I/O) | ||
|- | |- | ||
| Mach Speed || GTK6189 || Early 94 || 1 | | Mach Speed || GTK6189 || Early 94 || 1 || † No driver found. VLB card with a Cirrus CL-GD5428 VGA; the 40-pin IDE header has never been seen fitted, and some traces run to the VGA chip. The card ROM is a standard Cirrus VGA BIOS with nothing about IDE. Jumper positions are unpopulated except one that is hard-shorted, probably to disable the IDE function. Possibly IDE was dropped late in the design (owner's observation) | ||
|- | |- | ||
| Opus || Op VIC1 || Late 93 || 1 | | Opus || Op VIC1 || Late 93 || 1 || † No driver found. Op VIC (VIC = Vesa Ide Controller) | ||
|- | |- | ||
| Opus || Op VIC3 || Early 94 || 2 | | Opus || Op VIC3 || Early 94 || 2 || Op VIC (VIC = Vesa Ide Controller) | ||
|} | |} | ||
Revision as of 19:33, 12 November 2026
Full VL-bus IDE chip list
- † marks a value that was changed or added from the code. Where it replaces a spreadsheet value, the old value is given in brackets.
- - means nothing to record (no driver found, or the driver doesn't do it).
- ? means not known.
- The details behind the last three columns are in CHIP-ID.md (detection) and TIMING.md (timing registers, settings and PIO equivalents).
Software-configured
| Brand | Chip | Date | IDE Ports | Fastest Mode | IO RDY | Internal Strobes | Config Method | MR BIOS Support | XUB Support | Speed Settings | Notes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| ADD2 | DW729 | Late 93 | 2 | PIO-3 | Driver | Setup configures per drive | Notes: Driver Options: S/00 R/00 W/00 M/00 P/00. † Driver code is XOR-encrypted Other names: Dataworld DW729 Detection: Bases 100h-1C0h: out base,85h unlock, register 0Ah reads 41h ('A'). Genuine part: register 17h = B5hTiming registers: Registers 80h-87h at base+1 after each 85h unlockExamined: ADD_IDE.SYS 1.03 | ||||
| Appian | ADI/2 | Mid 93 | 1 | PIO-4 | Yes | Yes | Driver | 3.21 | † ctime=, dtime= (also c=, d=, s=, m=) [No flags] |
Notes: flexidrv.sys from Adaptec is best Other names: ALi M5213; AIC-25VL0x; CL-PD7220. † FLEXIDRV also drives the AIC-25PC10 (VL-bus or PCI) Detection: Ports 35h/B5h must differ from the PIC masks at 21h/A1h. † Then an ID echo at 0AD4h, 34h or B4h: ID 38h+ = AIC-25PC10 (VL-bus mode), lower = AIC-25VL01. The PCI 25PC10 is Appian 1097:0038Timing registers: † ID at base, index at base+4, data at base+8 (write the ID first). Registers 3/4 (drive 0) and 8/9 (drive 1): active clocks in bits 7-4, recovery clocks in bits 3-0. 7/12: address setup. 1: config; 13: revision Examined: FLEXIDRV.SYS 2.14 | |
| Atronics | IDE-2015PL | Late 94 | 2 | PIO-4 | Driver | /Dx:Px where x= 0-4. † /T:25/33/40/50 picks the bus-clock table |
Notes: 2015PL.SYS /Dx:P4 Other names: DTC 803 † (sticker on the 2015PL; VL DTC 2278S/D/D Plus/E/B and PCI 2130D) Detection: Index E0h/data E4h, then B0h/B4h; register echo with 3F6h reads between accessesTiming registers: One register per drive through the same index/data pair. † 2015PL.SYS: per-clock tables for PIO 0 / 3 / 4 at 25-50 MHz; /T:66 reads past the tables (bug). Linux dtc2278.c writes A0h/C3h for PIO 3+ at B0h/B4hExamined: 2015PL.SYS 3.27, DOSEIDE.SYS 2.1A | ||||
| CMD | PCI0640B | Late 94 | 2 | PIO-4 | Yes | Yes | Driver | 3.21 | /PIOMODE:X where x= 0-4. † CMD640X.VL 2.09 uses /A<MHz>, /O<port><drive><mode>, /H |
Notes: Stability issues at fastest speeds. † Hidden switches /CMD, /FOO:BARDetection: Index 178h/data 17Ch (else 78h/7Ch): register 50h not 00h/FFh, bit 5 set; register 5Bh echoes BDhTiming registers: Registers 51h-58h; per-drive clocks computed from /A<MHz>Examined: CMD640X.VL 2.09 | |
| Promise | PDC-20230c | Late 93 | 1 | PIO-3 | Yes | Yes | Driver | 3.21 | Yes | 1(slow), 8 (fast), A (iordy). † The PROMISE.SYS 3.3 README lists levels 0-8. † Config-mode 1F3h speeds 0-7: 630 to 240 ns at 33 MHz; jumpers give 2, 4, 6. † Levels 0-8 confirmed (owner); PROMISE.SYS has 9-entry tables, one per level |
Notes: † PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (owner) Other names: † Code name VG3, TurboChip C (Soucek) Detection: † Config-mode unlock on the IDE ports: in 1F5h, set 1F2h bit 7, in 1F2h, in 3F6h ×2, in 1F2h ×3; bit 7 reads back clear = PromiseTiming registers: Index 1F8h/data 1F9h: registers 2n/2n+1 get a word from one of four tables chosen by the measured bus speed. Register 7 = transfer status. † No chip ID read; same code for every Promise chip. † Four 9-entry tables (one per measured bus class), shared by all three Promise chipsExamined: PROMISE.SYS 3.3 (PROMISE.SYS 3.3; it doesn't name the chip) |
| Promise | PDC-20630 | Mid 94 | 2 | WDMA2 | Yes | Yes | Driver | 3.21 | Yes | 1(slow), 8 (fast), A (iordy) | Notes: Internal PIO Clock. † PROMISE.SYS 3.3 issues READ/WRITE DMA (C8h/CAh) and moves the data to memory by PIO from 1F0h. † PROMISE.SYS 3.3 supports the 20230-B, 20230-C and 20630 (owner)Other names: WDMA2 is chip-to-pata, no DMA to system RAM. † PROMISE.SYS 3.3 only ever sets the drive to multiword DMA mode 1 (SET FEATURES 21h, DMA levels 7-8); it never sends 22hDetection: † As PDC-20230c, then 1F4h bit 3 makes 1F8h read back its index (bits 0-2)Timing registers: † 1F3h speed as PDC-20230c, plus four timing registers through 1F8h/1F9h (enabled by 1F4h bit 3)Examined: PROMISE.SYS 3.3 (same code path; no chip check) |
| QDI | Vision 6500 | Mid 93 | 1 | PIO-2 | Driver | Yes | Setup configures per drive. † Driver picks a timing class from its drive table | Detection: Register 31h (or B1h): upper nibble C0h; bit 3 set = disabledTiming registers: One timing byte at 30h/B0h (active bits 0-2, recovery bits 4-7)Examined: QD6500.SYS 2.4 | |||
| QDI | Vision 6580 | Late 94 | 2 | PIO-4 | Card | Half | Driver | Yes | Setup configures per drive | Notes: PIO timing based on bus clock Detection: Register 31h (or B1h): upper nibble A0h or 50hTiming registers: As QD6500, plus secondary-channel timing Examined: qd6580.sys 3.7 | |
| SIS | 83C601 | Early 95 | 1 | PIO-4? | Yes | Yes | Driver | 3.21 | Waitstate 1 (fast) -7 (slow) | Notes: Newer than the 83C611 Tyan Driver is 1995-04. Early 95 is the earliest fab date seen. † SIIG also shipped its own drivers for this chip (owner) Other names: † PCI ID 1039:0601 (SIS611.SYS 08/94 already checks for it)Detection: in 1F3h; in 1F2h ×4; out 1F2h,F3h; 1F2h reads D3hTiming registers: 1F2h ← F0h + (wait state − 1) after the same unlockExamined: S134XM1.SYS 2.0, S134XD1.COM 3.5 (drivers don't name the chip; wait-state range matches) | |
| SIS | 83C611 | Late 93 | 1 | PIO-4? | Yes | Driver | 3.21 | † Wait state 0-7 for each channel | Notes: Older than the 83C601 Other names: † Driver banner says "VL/PCI-IDE"; the PCI check is unused Detection: Same 1F2h sequence (0C14h)Timing registers: 1F2h: F3h, B5h, then computed wait statesExamined: SIS611.SYS 2.11 | ||
| UMC | UM8672F | Late 94 | 1 | PIO-2 | Driver | Speeds 0 (slow) -11 (fast) | Notes: PIO-4 with Modded Driver. † Driver calls speed 10 the "proper speed" for Enhanced IDE drives Other names: UM82C872F Detection: None: 108h/109h unlocked with 5Ah, no ID read backTiming registers: Registers D0h-DDh through index 108h/data 109h; all set to CBh (slowest) first. † Six 12-entry tables in UM8672.SYS (chip ID A0h/A2h × 3 bus-speed classes). Linux umc8672.c uses the A0h slow-bus values (UMC-supplied). See TIMING.md, "Timing tables in the drivers"Examined: UM8672.SYS 2.1 | ||||
| VIA | VT83C461 | Mid 94 | 2 | PIO-2 | Yes | Driver | † PIO_TIME=, DMA_TIME=, SET_DMAM= |
Notes: Has a BIOS / AV140 / AV150 / AV300 Other names: † Driver also covers the VT82C496G Detection: Index A8h/data A9h: register 00h upper nibble 70h/90h, register 71h bit 0 setTiming registers: Registers 71h (IDE enable), 93h (timing/mode)Examined: VIAIDE.SYS 4.02 | |||
| Winbond | W83759AF | Early 95 | 2 | PIO-4 † (WBIDE.TXT's ns table makes speed 13 = PIO 3 at 33 MHz) | Yes | Yes | Driver | /D0:13 (speeds 0-13) | Notes: software speed config and "advanced mode". † Measures the bus clock with the PC timer. † A hacked driver that enables PIO 4 is reported to exist (owner) Other names: † DTC 2278E Rev W. † F = package type; the A suggests a silicon respin (owner) Detection: Bases 4B0h/5B0h… then 430h/530h…: 63h written at base+0 reads back at base+0Ch; register 87h low nibble = revision; register 80h bit 7 setTiming registers: Index base+4, data base+8 Examined: WBIDE.EXE, DOSEIDE.SYS 2.1A (at 5B0h only)
| ||
| Micronics | MIC491 | Mid 93 | 1 | ? | † BIOS Setup | † IDE Speed: Normal / Medium / Fast (register 104h = 69h / 67h / 63h) |
Notes: † No driver; the system BIOS sets it Other names: † Onboard on the Micronics GJX30G; BIOS says "Gateway 2000 Local Bus BIOS" Detection: † None. The BIOS only checks that no other IDE controller answers at 1F0hTiming registers: † out 9Ch,7Fh opens ports 102h-106h; 104h = speed, 102h bit 0 = IDE onExamined: GJX30G BIOS 09-24-93 |
Jumper-configured
| Brand | Chip | Date | IDE Ports | Fastest Mode | IO RDY | Config Method | Speed Settings | Notes |
|---|---|---|---|---|---|---|---|---|
| Chaintech | CT9000 | Late 93 | 1 | PIO-3 | Yes | Jumper | 0-3 | Notes: Not found yet: ct9000.zip |
| DTC | DTC 805 | Early 94 | 1 | PIO-2 | Jumper | 3.9MB/s - 7.2MB/s | Notes: † DOSEIDE.SYS has no code for it; it only shows the drive's reported rate Other names: † DTC 2278VL, jumpers W1-W5 Examined: DOSEIDE.SYS 2.1A | |
| GoldStar | GM82C711 | Early 93 | 1 | PIO-3 | Jumper | 0-7 | Notes: † GS_DOS.SYS never writes a timing register. † The same GS_DOS.SYS works on the GM82C712 (owner) Other names: Not a PC Chips 82C711 Detection: ? Examined: GS_DOS.SYS 1.21 (driver doesn't name the chip) | |
| GoldStar | GM82C712 | Mid 95 | 1 | PIO-4 | Yes | Jumper | 0-7 | Notes: † GS_DOS.SYS works on it too (owner) Other names: CompassLab CL3202. Not a PC Chips 82C712 Detection: ? Examined: GS_DOS.SYS 1.21 (owner: same driver as GM82C711) |
| Holtek | HT6560A | Late 94 | 2 | PIO-2 | Jumper | 0 (slow), 3 (fast) | Notes: Driver Not found yet | |
| Holtek | HT6560B | Early 95 | 2 | PIO-3 | Yes | † Jumper + Driver [Jumper] | 0 (slow), 3 (fast). † Driver /Dn=rt,at: recovery 2-16, active 2-15 bus clocks |
Notes: Driver allows AT:2 RT:2 Detection: 3E6h handshake: after three out 3E6h,0 / in 3E6h rounds some of bits 0-5 read back clear; on the fourth all six are setTiming registers: † Four reads of 3E6h, then config byte to 3E6h and timing byte (recovery << 4 OR active) to 1F6h [Timing bytes to 3E6h]. Linux pata_legacy 5.15 agreesExamined: HTIDE.SYS 2.41 |
| Lion | Lion 3+ | Mid 95 | 2 | PIO-3 | † Jumper + Driver [Jumper] | 0 (slow), 2(fast). † Driver sets a mode per drive | Notes: Doesn't support ECHS or LBA Detection: Config window on 1F0h/1F1h (opened by reads of 1F3h, 1F2h, 3F6h); register 5 & E0h = 60hTiming registers: Per-drive registers through the 1F0h/1F1h windowExamined: LION3.SYS | |
| OPTI | 82C611 | Early 93 | 2 | PIO-3 | Jumper | Notes: † Probably programmed the same way as the 82C611A; to be tested (owner) Other names: Opti VIC (VIC = Vesa Ide Controller) | ||
| OPTI | 82C611A | Late 94 | 2 | PIO-3 | Card | † Jumper + Driver [Jumper] | 0 (slow), 3 (fast). † SETUPVIC: read/write pulse, recovery, address setup in ns; 25/33 MHz | Other names: Opti VIC (VIC = Vesa Ide Controller) Detection: 1F3h echoes C0h; then in 1F1h ×2, out 1F2h,03h (config mode), 1F3h changes, out 1F2h,83hTiming registers: In config mode: 1F3h selects the drive bank, 1F1h = write timing, 1F6h = setup and read bank, 1F0h = read timing, 1F5h bits 0-1 = bus-clock strap. † Linux pata_legacy 5.15 uses the same sequence for the 82C611AExamined: optivic.sys 1.0, opti-pio.exe, opti-set.exe (drivers don't name the chip) |
| PiC | 1288A-125 | Late 93 | 1 | PIO-2 | Yes | Jumper | 0 (slow), 3 (fast) | Notes: Driver Not found yet Other names: VIDE-1 |
| Promise | PDC-20230b | Mid 93 | 1 | PIO-3 | Jumper | 0 (slow), 2(fast) | Notes: † Works with the PROMISE.SYS 3.3 drivers (owner). † PROMISE.SYS 3.3 supports it (owner) Other names: CompassLab CL3201 (9314) ? † Code name TurboChip B; jumper speeds 0, 1, 2 (Soucek) Detection: † No config mode. Write 55h to 1F2h, read it three times back to back: a 20230-B returns 00h on the third read (Soucek; also unreached code in PROMISE.SYS at 2D3Bh). Needs the same three reads as a "VLB sync" before 32-bit I/OTiming registers: - (jumpers) Examined: PROMISE.SYS 3.3 | |
| UMC | UM82C871F | Mid 93 | 1 | PIO-3 | Jumper | Best speed: AT:3 RT:4 | Notes: † Driver only uses standard IDE commands; its F5 setup only toggles multi-sector mode Examined: UM82C871F.SYS | |
| UMC | UM85C418F | Late 93 | 1 | PIO-2 | † Jumper; driver overrides for 28 listed drives [Jumper] | Best speed: AT:5 RT:9 | Notes: Combo IDE & VGA controller. † The driver writes register D1h only when every drive is in its tableOther names: Stability issues at fastest speeds Detection: None: 108h/109h unlocked with 5Ah, no ID read backTiming registers: Register D1h through index 108h/data 109h (one value for both drives)Examined: UM85C418F.SYS 1.07 | |
| Winbond | W83759F | Early 94 | 2 | PIO-2 | Jumper | 600ns, 500ns, 400ns, 240ns | Notes: winbond_port † (Linux pata_legacy parameter; default base 130h, alternate 1B0h)Other names: † Same probe as the W83759AF? WBIDE reads a revision letter; DOSEIDE needs revision B or later. Linux only programs the W83759A, after turning off jumper mode (register 81h bit 7). † F = package type (owner)Detection: ? |
No configuration software found
No driver or setup utility has been found for these chips.
| Brand | Chip | Date | IDE Ports | Notes |
|---|---|---|---|---|
| QDI | Vision 5500 | Early | 1 | Not found yet: QDI5500.sys. † The only reference to this chip found so far is in TH99; Linux pata_legacy has no QD5500 support (only QD6500/6580/6580DP) |
| Tans | TS8310 | Mid 94 | 2 | Not found yet: ts8310.zip, BIOS was generic. † Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997), v2.10 ">8.4GB" (1999), and SIIG v3.10, which is TANS v2.00 with only the name changed (18 bytes differ). All use only the standard IDE ports at 1F0h/170h/1E8h/168h: no chip detection, no timing writes, and 16-bit rep insw/outsw only (no 32-bit I/O)
|
| Tans | TS8310A | Late 94 | 2 | Not found yet: ts8310.zip, BIOS was generic. † Three option ROMs from TANS cards checked: TANS "Enhance IDE driver" v2.00 (1997), v2.10 ">8.4GB" (1999), and SIIG v3.10, which is TANS v2.00 with only the name changed (18 bytes differ). All use only the standard IDE ports at 1F0h/170h/1E8h/168h: no chip detection, no timing writes, and 16-bit rep insw/outsw only (no 32-bit I/O)
|
| Mach Speed | GTK6189 | Early 94 | 1 | † No driver found. VLB card with a Cirrus CL-GD5428 VGA; the 40-pin IDE header has never been seen fitted, and some traces run to the VGA chip. The card ROM is a standard Cirrus VGA BIOS with nothing about IDE. Jumper positions are unpopulated except one that is hard-shorted, probably to disable the IDE function. Possibly IDE was dropped late in the design (owner's observation) |
| Opus | Op VIC1 | Late 93 | 1 | † No driver found. Op VIC (VIC = Vesa Ide Controller) |
| Opus | Op VIC3 | Early 94 | 2 | Op VIC (VIC = Vesa Ide Controller) |