GoldStar Prime 2C MKIII - Revision history

Malvineous: Update infobox

2016-02-13T06:12:52Z

Update infobox

← Older revision		Revision as of 16:12, 13 February 2016
Line 1:		Line 1:
	{{~~SuperIO~~ Infobox		{{Device Infobox/Begin
	\| Bus type = ISA		\| Bus type = ISA
	\| Bus width = 16-bit		\| Bus width = 16-bit
Line 8:		Line 8:
	\| Compatible with = [[Has compatibility::IDE]], [[Has compatibility::PC Floppy]], [[Has compatibility::RS232]], [[Has compatibility::LPT]], [[Has compatibility::Gameport]]		\| Compatible with = [[Has compatibility::IDE]], [[Has compatibility::PC Floppy]], [[Has compatibility::RS232]], [[Has compatibility::LPT]], [[Has compatibility::Gameport]]
	\| Connectors = [[Has connector::RS232/DB9]], [[Has connector::LPT]] <!-- Other connectors aren't shipped with the card so aren't included -->		\| Connectors = [[Has connector::RS232/DB9]], [[Has connector::LPT]] <!-- Other connectors aren't shipped with the card so aren't included -->
	\| ~~ROM type~~ = ~~None~~		\| Requires -5VDC = No
			\| Requires -12VDC = Yes
			\| Config = [[Config method::Jumpers]]
			}}
			{{Device Infobox/IO
	\| Serial ports = 2		\| Serial ports = 2
			\| UART =
			\| COM1 = Yes
			\| COM2 = Yes
			\| COM3 = Yes
			\| COM4 = Yes
	\| Parallel ports = 1		\| Parallel ports = 1
			\| Bi-dir =
			\| ECP =
			\| EPP =
			\| LPT1 = Yes
			\| LPT2 = Yes
			\| LPT3 = No
			\| LPT4 = No
	\| Game ports = 1		\| Game ports = 1
			}}
			{{Device Infobox/Floppy Controller
	\| Floppy buses = 1		\| Floppy buses = 1
	\| Secondary ~~floppy~~ = Yes		\| Drives per bus = 2
			\| Secondary = Yes
			\| ROM type = None
			}}
			{{Device Infobox/IDE Controller
	\| IDE buses = 1		\| IDE buses = 1
	\| ~~ST-506 buses~~ = 0		\| Primary = Yes
	\| ~~Requires -5VDC~~ =		\| Secondary = Yes
	\| ~~Requires -12VDC~~ =		\| Tertiary = No
	\| ~~Config~~ = ~~[[Config method::Jumpers]]~~		\| Quaternary = No
			\| ROM type = None
			}}
			{{Device Infobox/End
	\| Driver = N/A		\| Driver = N/A
	}}		}}
Line 26:		Line 51:
	The card's part number is P2C94002.		The card's part number is P2C94002.

	The TH99 entry ~~seems to have~~ some mistakes, such as a jumper toggling between "primary IDE enabled" or "secondary IDE disabled". Since there is already a separate jumper to enable/disable the IDE interface, this is ~~probably~~ meant to switch the interface between primary and secondary when it is enabled. The same goes for the floppy interface. This page should be updated ~~once this has been tested~~.		The TH99 entry has some mistakes, such as a jumper toggling between "primary IDE enabled" or "secondary IDE disabled". Since there is already a separate jumper to enable/disable the IDE interface, this is actually meant to switch the interface between primary and secondary when it is enabled. The same goes for the floppy interface.

			This card is notable because the serial ports can be set to use IRQs 5 and 9, which will prevent them from conflicting with the default IRQs of 4 and 3, should the card be added as an additional controller.

			The pinout for the serial headers is currently unknown. There are two types in common use. This page should be updated when the correct type is known.

	== Additional photos ==		== Additional photos ==

Malvineous: MFM -> ST-506

2016-02-05T13:33:06Z

MFM -> ST-506

← Older revision		Revision as of 23:33, 5 February 2016
Line 15:		Line 15:
	\| Secondary floppy = Yes		\| Secondary floppy = Yes
	\| IDE buses = 1		\| IDE buses = 1
	\| ~~MFM~~ buses = 0		\| ST-506 buses = 0
	\| Requires -5VDC =		\| Requires -5VDC =
	\| Requires -12VDC =		\| Requires -12VDC =

Malvineous: Basic info

2016-01-31T10:16:03Z

Basic info

New page

{{SuperIO Infobox
| Bus type = ISA
| Bus width = 16-bit
| Bus speed = 8 MHz
| 8-bit ISA compatible =
| Manufacturer = GoldStar
| Chipset = GoldStar Prime 2C
| Compatible with = [[Has compatibility::IDE]], [[Has compatibility::PC Floppy]], [[Has compatibility::RS232]], [[Has compatibility::LPT]], [[Has compatibility::Gameport]]
| Connectors = [[Has connector::RS232/DB9]], [[Has connector::LPT]] 
| ROM type = None
| Serial ports = 2
| Parallel ports = 1
| Game ports = 1
| Floppy buses = 1
| Secondary floppy = Yes
| IDE buses = 1
| MFM buses = 0
| Requires -5VDC =
| Requires -12VDC =
| Config = [[Config method::Jumpers]]
| Driver = N/A
}}

The '''GoldStar Prime 2C MKIII''' is a Super I/O board from GoldStar using their own chipset.

The card's part number is P2C94002.

The TH99 entry seems to have some mistakes, such as a jumper toggling between "primary IDE enabled" or "secondary IDE disabled". Since there is already a separate jumper to enable/disable the IDE interface, this is probably meant to switch the interface between primary and secondary when it is enabled. The same goes for the floppy interface. This page should be updated once this has been tested.

== Additional photos ==

<gallery mode="packed">
Image:GoldStar Prime 2C MKIII underside.jpg|Underside
</gallery>

== Related links ==

* FCC ID is [https://fccid.io/JGBPRIME2C JGBPRIME2C]
* [https://th99.bl4ckb0x.de/c/U-Z/21437.htm TH99]