Creative Sound Blaster Pro 2 - Revision history

Malvineous: Add audio extension connector pinouts

2017-01-08T12:28:32Z

Add audio extension connector pinouts

Malvineous: Rename Dupont connectors

2016-04-16T22:50:28Z

Rename Dupont connectors

Malvineous: Update internal connectors

2016-03-20T09:26:28Z

Update internal connectors

Malvineous: Add pics for early revision

2016-03-20T00:27:45Z

Add pics for early revision

Malvineous: CD interface -> Has CD interface

2016-02-13T08:43:38Z

CD interface -> Has CD interface

Malvineous: Update infobox

2016-02-13T08:41:30Z

Update infobox

Malvineous: -5V no, -12V yes

2016-02-03T06:46:59Z

-5V no, -12V yes

Malvineous: Joystick -> Gameport

2016-01-26T13:26:48Z

Joystick -> Gameport

Malvineous: Basic info

2016-01-24T06:05:05Z

Basic info

New page

{{Sound Infobox
| Bus type = ISA
| Bus width = 16-bit
| Bus speed = 8 MHz
| 8-bit ISA compatible = Yes
| Manufacturer = Creative Labs
| Model = CT1600
| Chipset = CT1336A
| Compatible with = [[Has compatibility::Sound Blaster]]
| Connectors = [[Has connector::Mic]], [[Has connector::Line out]], [[Has connector::Speaker out]], [[Has connector::Joystick]]
| Full duplex =
| Max sample rate =
| Channels = 2
| FM synth = OPL3
| Max memory = 0
| CD interface = [[CD interface::Matsushita MKE]]
| Config = [[Config method::Jumpers]]
| Requires -5VDC =
| Requires -12VDC = No
| Driver
}}

The '''Sound Blaster Pro 2''' was a revision to the original [[Creative Sound Blaster Pro|SB Pro]], replacing the dual OPL2 chips with a single OPL3. The card is technically only an 8-bit one - the extra connectors that fit into the 16-bit slot are only used for selecting IRQ 10 and/or DMA 0.

== Additional photos ==

<gallery mode="packed">
Image:Creative Sound Blaster Pro 2 underside.jpg|Underside
</gallery>

← Older revision		Revision as of 12:28, 8 January 2017
Line 36:		Line 36:
	Image:Creative Sound Blaster Pro 2 early underside.jpg\|Underside of early revision		Image:Creative Sound Blaster Pro 2 early underside.jpg\|Underside of early revision
	</gallery>		</gallery>
		+
		+	== Jumpers ==
		+
		+	=== JP2: Audio extension connector ===
		+
		+	These pins provide speaker output and microphone input for interfacing with other cards<ref name="getting-started">Sound Blaster Pro - Getting Started manual, section D-2.</ref>. They are located just behind the mic/line jacks.
		+
		+	{\|class="wikitable"
		+	! Pin !! Name !! Purpose
		+	\|-
		+	\| 1 \|\| MICR \|\| Mic input, right channel. Input from 0.004 to 0.7 V rms.
		+	\|-
		+	\| 2 \|\| MICGEN \|\| Mic input, ground.
		+	\|-
		+	\| 3 \|\| MICL \|\| Mic input, left channel. Input from 0.004 to 0.7 V rms.
		+	\|-
		+	\| 4 \|\| SPKGND \|\| Speaker output, ground.
		+	\|-
		+	\| 5 \|\| SPKR \|\| Speaker output, right channel. Maximum output voltage is 3 V rms at 4 ohms.
		+	\|-
		+	\| 6 \|\| SPKL \|\| Speaker output, left channel. Maximum output voltage is 3 V rms at 4 ohms.
		+	\|-
		+	\| 7 \|\| SPKRL \|\| Speaker output return, left channel.
		+	\|-
		+	\| 8 \|\| SPKRR \|\| Speaker output return, right channel.
		+	\|}
		+
		+	=== JP3: PC Speaker output connector ===
		+
		+	These pins provide an output<ref name="getting-started"/> that can be connected to the internal PC speaker, to allow all audio from the card to be heard through the internal speaker. It is currently unknown whether this output is muted when the line-out jack is in use. The jumper is located next to JP2.
		+
		+	{\|class="wikitable"
		+	! Pin !! Name !! Purpose
		+	\|-
		+	\| 1 \|\| SPKR \|\| Speaker output, right channel. Maximum output voltage is 3 V rms at 4 ohms.
		+	\|-
		+	\| 2 \|\| SPKRR \|\| Speaker output return, right channel.
		+	\|}
		+
		+	== References ==
		+
		+	<references/>

@@ Line 19: / Line 19: @@
   | FM synth = OPL3
   | Input/CD = [[Has CD audio input connector::SBCD]]
-  | Input/PC = [[Has PC speaker input connector::2-pin Dupont]]
+  | Input/PC = [[Has PC speaker input connector::Dupont-2]]
   | Factory memory = 0
   | CD interface = [[Has CD interface::Matsushita MKE]]

@@ Line 18: / Line 18: @@
   | Channels = 2
   | FM synth = OPL3
   | Factory memory = 0
   | CD interface = [[Has CD interface::Matsushita MKE]]
 }}

@@ Line 20: / Line 20: @@
   | Factory memory = 0
   | Max memory = 0
-  | CD interface = [[CD interface::Matsushita MKE]]
+  | CD interface = [[Has CD interface::Matsushita MKE]]
 }}
 {{Device Infobox/End

@@ Line 32: / Line 32: @@
 <gallery mode="packed">
 Image:Creative Sound Blaster Pro 2 underside.jpg|Underside
 </gallery>

@@ Line 1: / Line 1: @@
-{{Sound Infobox
+{{Device Infobox/Begin
   | Bus type = ISA
   | Bus width = 16-bit
@@ Line 5: / Line 5: @@
   | 8-bit ISA compatible = Yes
   | Manufacturer = Creative Labs
   | Chipset = CT1336A
   | Compatible with = [[Has compatibility::Sound Blaster]]
   | Connectors = [[Has connector::Mic]], [[Has connector::Line out]], [[Has connector::Speaker out]], [[Has connector::Gameport]]
   | Full duplex =
   | Max sample rate =
   | Channels = 2
   | FM synth = OPL3
   | Max memory = 0
   | CD interface = [[CD interface::Matsushita MKE]]
- | Config = [[Config method::Jumpers]]
+}}
- | Requires -5VDC = No
+{{Device Infobox/End
   | Driver<!-- TODO -->
 }}