Creative Sound Blaster 32 PnP - Revision history

Malvineous: Add note about secondary IDE issues

2017-02-26T01:04:03Z

Add note about secondary IDE issues

← Older revision		Revision as of 11:04, 26 February 2017
Line 47:		Line 47:
	Image:Creative Sound Blaster 32 PnP underside.jpg\|Underside		Image:Creative Sound Blaster 32 PnP underside.jpg\|Underside
	</gallery>		</gallery>

			== IDE interface ==

			While the PnP nature of the card allows the IDE interface to be configured on a wide variety of ports (allowing even more than four IDE interfaces in a single system), one caveat applies. When the card is configured as a secondary IDE controller, the second group of I/O addresses is truncated. Normally the second IDE controller also uses ports 376-377, however this can conflict with the floppy controller, so the PnP settings only reserve port 376. In this case, some CD-ROM device drivers (such as [[VIDE-CDD.SYS]]) will not recognise the interface. Because of this, setting the card to the secondary IDE interface is not recommended. It works well as the third or fourth IDE interface as the ports are not truncated with these settings.

Malvineous: Mention onboard memory as another difference between SB32 and AWE32

2017-02-21T11:35:04Z

Mention onboard memory as another difference between SB32 and AWE32

← Older revision		Revision as of 21:35, 21 February 2017
Line 40:		Line 40:
	The '''Sound Blaster 32 PnP''' is an update to the Sound Blaster 16 with the ''WavEffects'' (EMU8000) chip from the [[Creative Sound Blaster AWE32\|AWE32]]. It is one of the few Creative Labs cards that can take standard 30-pin SIMMs to increase the memory available for MIDI instrument samples.		The '''Sound Blaster 32 PnP''' is an update to the Sound Blaster 16 with the ''WavEffects'' (EMU8000) chip from the [[Creative Sound Blaster AWE32\|AWE32]]. It is one of the few Creative Labs cards that can take standard 30-pin SIMMs to increase the memory available for MIDI instrument samples.

	It is very similar to the [[Creative Sound Blaster AWE32 PnP (IDE)]], but with a CT1749 instead of the CT8903 (AWE32) chip. It also has a SPDIF output connector, which the AWE32 does not.		It is very similar to the [[Creative Sound Blaster AWE32 PnP (IDE)]], but with a CT1749 instead of the CT8903 (AWE32) chip. It also has a SPDIF output connector, which the AWE32 does not. The SB32 series also has no onboard memory, while the AWE32 has 512 kB.

	== Additional photos ==		== Additional photos ==

Malvineous: Include allowed IDE settings

2017-02-21T11:33:29Z

Include allowed IDE settings

← Older revision		Revision as of 21:33, 21 February 2017
Line 28:		Line 28:
	{{Device Infobox/IDE Controller		{{Device Infobox/IDE Controller
	\| IDE buses = 1		\| IDE buses = 1
			\| Primary = N
			\| Secondary = Y
			\| Tertiary = Y
			\| Quaternary = Y
	\| ROM type = None		\| ROM type = None
	}}		}}

Malvineous: Rename Dupont connectors

2016-04-16T22:47:15Z

Rename Dupont connectors

← Older revision		Revision as of 08:47, 17 April 2016
Line 19:		Line 19:
	\| FM synth = CQM		\| FM synth = CQM
	\| Input/CD = [[Has CD audio input connector::SBCD]], [[Has CD audio input connector::MPC]]		\| Input/CD = [[Has CD audio input connector::SBCD]], [[Has CD audio input connector::MPC]]
	\| Input/PC = [[Has PC speaker input connector::2~~-pin Dupont~~]]		\| Input/PC = [[Has PC speaker input connector::Dupont-2]]
	\| Output/SPDIF = [[Has SPDIF output connector::2~~-pin Dupont~~]]		\| Output/SPDIF = [[Has SPDIF output connector::Dupont-2]]
	\| Has MB_PRO = Yes		\| Has MB_PRO = Yes
	\| Factory memory =		\| Factory memory =

Malvineous: Add board

2016-04-16T22:27:21Z

Add board

New page

{{Device Infobox/Begin
| Bus type = ISA
| Bus width = 16-bit
| Bus speed = 8 MHz
| 8-bit ISA compatible =
| Manufacturer = Creative Labs
| Chipset = CT1749
| Compatible with = [[Has compatibility::Sound Blaster]], [[Has compatibility::30-pin SIMM]]
| Connectors = [[Has connector::Mic]], [[Has connector::Line in]], [[Has connector::Line out]], [[Has connector::Speaker out]], [[Has connector::Gameport]]
| Requires -5VDC = No
| Requires -12VDC = Yes
| Config = [[Config method::PnP]]
}}
{{Device Infobox/Audio
| Model = CT3620
| Full duplex =
| Max sample rate =
| Channels = 2
| FM synth = CQM
| Input/CD = [[Has CD audio input connector::SBCD]], [[Has CD audio input connector::MPC]]
| Input/PC = [[Has PC speaker input connector::2-pin Dupont]]
| Output/SPDIF = [[Has SPDIF output connector::2-pin Dupont]]
| Has MB_PRO = Yes
| Factory memory =
| Max memory = 28MB
| CD interface = [[Has CD interface::IDE]]
}}
{{Device Infobox/IDE Controller
| IDE buses = 1
| ROM type = None
}}
{{Device Infobox/End
| Driver
}}

The '''Sound Blaster 32 PnP''' is an update to the Sound Blaster 16 with the ''WavEffects'' (EMU8000) chip from the [[Creative Sound Blaster AWE32|AWE32]]. It is one of the few Creative Labs cards that can take standard 30-pin SIMMs to increase the memory available for MIDI instrument samples.

It is very similar to the [[Creative Sound Blaster AWE32 PnP (IDE)]], but with a CT1749 instead of the CT8903 (AWE32) chip. It also has a SPDIF output connector, which the AWE32 does not.

== Additional photos ==

<gallery mode="packed">
Image:Creative Sound Blaster 32 PnP underside.jpg|Underside
</gallery>