Difference between revisions of "MB PRO"
Malvineous (Talk | contribs) (Add pinouts) |
(Updated info about AC'97 mod) |
||
(3 intermediate revisions by 2 users not shown) | |||
Line 9: | Line 9: | ||
|} | |} | ||
− | The purpose of the pins, from the point of view of the sound card, are:<ref>[http://support.creative.com/kb/ShowArticle.aspx?sid=3026 Creative Labs - Pin Assignment of I/O Jacks and Connectors on Sound Blaster Devices]</ref> | + | The purpose of the pins, from the point of view of the sound card, are:<ref><s>[http://support.creative.com/kb/ShowArticle.aspx?sid=3026 Creative Labs - Pin Assignment of I/O Jacks and Connectors on Sound Blaster Devices]</s> Link dead, need archived mirror</ref> |
{|class="wikitable" | {|class="wikitable" | ||
Line 22: | Line 22: | ||
| 4 || Audio GND | | 4 || Audio GND | ||
|- | |- | ||
− | | 5 || Line | + | | 5 || Line out left |
|- | |- | ||
| 6 || Audio GND | | 6 || Audio GND | ||
|- | |- | ||
− | | 7 || Line | + | | 7 || Line out right |
|- | |- | ||
− | | 8 || Modem speaker input | + | | 8 || Modem speaker input. On a sound card, this input receives a line-level audio signal from the modem. |
|- | |- | ||
| 9 || Audio GND | | 9 || Audio GND | ||
Line 34: | Line 34: | ||
| 10 || Microphone in '''Isn't this mic out for the modem?''' | | 10 || Microphone in '''Isn't this mic out for the modem?''' | ||
|} | |} | ||
+ | |||
+ | == AC'97 mod == | ||
+ | It is possible to connect AC'97 front panel pins to a MB_PRO header, although it's still a work in progress. | ||
+ | |||
+ | {|class="wikitable" | ||
+ | ! AC'97 pin !! Sound card<br/>MB_PRO pin !! Purpose | ||
+ | |- | ||
+ | | 5 || 7 || Line out right | ||
+ | |- | ||
+ | | 2 || 6 || Line out right GND | ||
+ | |- | ||
+ | | 9 || 5 || Line out left | ||
+ | |- | ||
+ | | 2 || 4 || Line out left GND | ||
+ | |} | ||
+ | |||
+ | For now it seems that all ground must go to pin 2 on AC'97 side. Some pinouts say that pins 4, 6 and 10 are ground, but that is demonstrably untrue. Those pins are for plug detection of associated pins. | ||
+ | Microphone seems to be located on pin 10 on MBPRO side of things and should go to pin 1 on AC'97, but it's quite possible that auxilary power will be required for pin 3 on AC'97. | ||
+ | |||
+ | == TAD conversion == | ||
+ | |||
+ | Some sound cards have an '''MB_PRO''' connector but no [[TAD]] connector. A cable can be made to allow internal modems with a TAD socket to be hooked up to the MB_PRO connector: | ||
+ | |||
+ | {|class="wikitable" | ||
+ | ! Modem<br/>TAD pin !! Sound card<br/>MB_PRO pin !! Purpose | ||
+ | |- | ||
+ | | 1 || 8 || Phone line audio, from modem to sound card. | ||
+ | |- | ||
+ | | 2 || 6 || GND | ||
+ | |- | ||
+ | | 3 || 9 || GND | ||
+ | |- | ||
+ | | 4 || 10 || Microphone audio, from sound card to modem. | ||
+ | |} | ||
+ | |||
+ | TAD pins 2 and 3 can also be patched to any of the other GND signals on the MB_PRO connector if that is more convenient. The two in the above table are just one possibility. | ||
== References == | == References == | ||
<references/> | <references/> |
Latest revision as of 10:19, 13 August 2022
The MB_PRO connector is used to connect a Sound Blaster card to a Modem Blaster card. The signals can also be re-purposed for other uses.
The pin arrangement is as follows:
9 | 7 | 5 | 3 | 1 |
10 | 8 | 6 | 4 | N/C |
The purpose of the pins, from the point of view of the sound card, are:[1]
Pin | Purpose |
---|---|
1 | Audio GND |
2 | Key, no pin |
3 | Line-in |
4 | Audio GND |
5 | Line out left |
6 | Audio GND |
7 | Line out right |
8 | Modem speaker input. On a sound card, this input receives a line-level audio signal from the modem. |
9 | Audio GND |
10 | Microphone in Isn't this mic out for the modem? |
AC'97 mod
It is possible to connect AC'97 front panel pins to a MB_PRO header, although it's still a work in progress.
AC'97 pin | Sound card MB_PRO pin |
Purpose |
---|---|---|
5 | 7 | Line out right |
2 | 6 | Line out right GND |
9 | 5 | Line out left |
2 | 4 | Line out left GND |
For now it seems that all ground must go to pin 2 on AC'97 side. Some pinouts say that pins 4, 6 and 10 are ground, but that is demonstrably untrue. Those pins are for plug detection of associated pins. Microphone seems to be located on pin 10 on MBPRO side of things and should go to pin 1 on AC'97, but it's quite possible that auxilary power will be required for pin 3 on AC'97.
TAD conversion
Some sound cards have an MB_PRO connector but no TAD connector. A cable can be made to allow internal modems with a TAD socket to be hooked up to the MB_PRO connector:
Modem TAD pin |
Sound card MB_PRO pin |
Purpose |
---|---|---|
1 | 8 | Phone line audio, from modem to sound card. |
2 | 6 | GND |
3 | 9 | GND |
4 | 10 | Microphone audio, from sound card to modem. |
TAD pins 2 and 3 can also be patched to any of the other GND signals on the MB_PRO connector if that is more convenient. The two in the above table are just one possibility.
References
- ↑
Creative Labs - Pin Assignment of I/O Jacks and Connectors on Sound Blaster DevicesLink dead, need archived mirror